កិច្ចសហប្រតិបត្តិការ
សិល្បៈ
សម្រស់ និង សុខុមាលភាព
សិប្បកម្ម
វប្បធម៌ និង ប្រវត្តិសាស្ត្រ
ការកម្សាន្ត
បរិស្ថាន
ម្ហូប និង ភេសជ្ជៈ
វិស្វកម្មបញ្ច្រាស
វិទ្យាសាស្ត្រ
កីឡា
បច្ចេកវិទ្យា
ប្រដាប់ដែលស្លៀក

Cane Glue Brush: the Bark Stripped from One End and the Fibres Hammered Loose (Adamson, Amateur Work, 1887)
The fret-cutter's glue brush recommended by D. B. Adamson in Amateur Work (1887): a piece of cane with the hard outer skin cut away at one end and the end hammered until the fibres loosen into a stiff brush, "better than any other" for rubbing glue into wood.
ចាប់ផ្តើម
A few minutes
ការណែនាំ
1
1
Read Adamson
Read Adamson
"Nothing is better than a piece of cane beaten out at one end."
2
2
Strip the end
Strip the end
Take a piece of cane (ours: about 15-20 cm) and cut off the hard outer covering for a short distance at one end (ours: about 2 cm).
សម្ភារៈសម្រាប់ជំហាននេះ៖
ផ្ដៅ1 ដុំឧបករណ៍ដែលត្រូវការ៖
កាំបិតឧបករណ៍3
3
Beat out the fibres
Beat out the fibres
Lay the stripped end on a hard surface and hammer it until the fibres loosen into a brush.
ឧបករណ៍ដែលត្រូវការ៖
ញញួរ4
4
Use it
Use it
Warm the glue by standing its can or bottle in a basin of hot water, then rub the glue well into the wood with the brush.
សម្ភារៈសម្រាប់ជំហាននេះ៖
ទឹក1 ដុំឧបករណ៍ដែលត្រូវការ៖
ធុង
កាវ5
5
Troubleshooting
Troubleshooting
Cane brush troubleshooting.
Flow
Loading...
6
6
History and honest limits
History and honest limits
From D. B. Adamson, "Fretsaw Work and Marquetry Cutting" III, **Amateur Work, Illustrated**, vol. VII (1887), p. 230 (checked on the archive.org scan amateurworkillus71887lond). He gives no lengths: those and the knife are ours.
ប្លង់នេះធ្វើ
CC0 សាធារណៈ
ប្លង់នេះត្រូវបានចេញផ្សាយក្រោម CC0។ អ្នកមានសិទ្ធិចម្លង កែប្រែ ចែកចាយ និងប្រើប្រាស់ដោយមិនចាំបាច់សុំអនុញ្ញាត។
គាំទ្រអ្នកបង្កើតដោយទិញផលិតផលតាមរយៈប្លង់របស់ពួកគេ ដែលពួកគេទទួលបាន កម្រៃជើងសារអ្នកបង្កើត កំណត់ដោយអ្នកលក់ ឬបង្កើតកំណែថ្មីនៃប្លង់នេះ ហើយបញ្ចូលជាការតភ្ជាប់ក្នុងប្លង់របស់អ្នកដើម្បីចែករំលែកចំណូល។
