សិល្បៈ
សម្រស់ និង សុខុមាលភាព
សិប្បកម្ម
វប្បធម៌ និង ប្រវត្តិសាស្ត្រ
ការកម្សាន្ត
បរិស្ថាន
ម្ហូប និង ភេសជ្ជៈ
វិស្វកម្មបញ្ច្រាស
វិទ្យាសាស្ត្រ
កីឡា
បច្ចេកវិទ្យា
ប្រដាប់ដែលស្លៀក
Air-Pump Tube Dasher: A Tube Over a Loose Plunger Pumps Air at Every Stroke
Wright wanted a hand dasher that "will operate as an air pump to force a stream of air into the cream at the same time that it agitates it."
William M. Wright of Pittsburgh, Pennsylvania, received US 6,711, dated 11 September 1849, for an atmospheric churn-dasher: a tube of tinned sheet iron with a flange on its lower end, a cap with a valve opening inward, and a handle; inside, a loose cylinder of wood weighted at its lower end rests on the bottom of the tub as a plunger. Worked like a common dasher in "almost any ordinary pail or dairy vessel," it discharges air among the cream on each descent and refills on each ascent.
This rung works out the air per stroke, then prints the cap, flange and plunger, assembles them on a pipe, and makes butter in a pail.
ចាប់ផ្តើម
About 1 hour, plus printing
ការណែនាំ
1
1
Air per stroke
Air per stroke
កំពុងផ្ទុកសៀវភៅ Jupyter…
2
2
A dash closing over a fixed block before it
A dash closing over a fixed block before it
The embedded blueprint squeezes air from a hollow dash over a block fixed to the churn. Wright's plunger is loose, so it needs no fixing at all.
3
3
Read US 6,711
Read US 6,711
"From the fact of the piston resting loosely upon the bottom of the tub, and being capable of moving about and occupying a vertical or inclined position as may best suit the convenience of the operator, and also from the facility with which it and the dasher may be removed from the churn tub and cleaned, and from the simplicity of all the parts being a guarantee against their getting out of order, this apparatus is applicable to churning cream in either large or small quantities."
4
4
Print the parts
Print the parts
Print the cap (/uploads/blueprints/air-pump-tube-dasher-cap.stl) with its side valve port and handle socket, the foot flange (/uploads/blueprints/air-pump-tube-dasher-flange.stl), and the plunger (/uploads/blueprints/air-pump-tube-dasher-plunger.stl), whose foot has a pocket for a steel weight. Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
សម្ភារៈសម្រាប់ជំហាននេះ៖
សរសៃ PETG1 ដុំឧបករណ៍ដែលត្រូវការ៖
ម៉ាស៊ីនបោះពុម្ព 3D ប្រើខ្សែ (FDM)5
5
Valve and weight
Valve and weight
Glue a small leather flap inside the cap over the valve port, along its top edge only, so air enters and cannot leave. Glue an M10 carriage bolt into the plunger's pocket, so it sinks in cream as he weighted his with metal.
សម្ភារៈសម្រាប់ជំហាននេះ៖
ចំណិតស្បែក1 ដុំ
ប៊ូឡុងក្បាលមូល1 ដុំ
អេប៉ុកស៊ីពីរផ្នែក1 ដុំឧបករណ៍ដែលត្រូវការ៖
ឈុតទួណឺវីស6
6
Assemble
Assemble
Cut 300 mm of 50 mm pipe. Push the flange onto its foot and the cap onto its top, and glue a hardwood dowel handle in the cap's socket. Stand the plunger in a tall food-grade bucket and lower the tube over it.
សម្ភារៈសម្រាប់ជំហាននេះ៖
បំពង់ PVC1 ដុំ
ដែកគោលឈើរឹង1 ដុំ
ធុង ២០ លីត្រ1 ដុំអេប៉ុកស៊ីពីរផ្នែក1 ដុំឧបករណ៍ដែលត្រូវការ៖
រណារកាត់ដែក
ក្រដាសខាត់7
7
The build in 3D
The build in 3D
FreeCAD model of this build, not of the patent: the pail, tube and flange cut away to show the loose weighted plunger standing on the bottom inside the tube, the cap with its valve, and the handle.
8
8
Dash and make butter
Dash and make butter
Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Pour in 2 litres. Work the tube up and down over the plunger; bubbles should burst from under the flange on each down-stroke. Time until the butter comes. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.
សម្ភារៈសម្រាប់ជំហាននេះ៖
ក្រែមខាប់2000 មល
អំបិលសមុទ្រគ្រើម1 ដុំ
ទឹក1 ដុំឧបករណ៍ដែលត្រូវការ៖
ទែម៉ូម៉ែត្រមានចុងដោតទុក
នាឡិកាបញ្ឈប់
ជញ្ជីងឌីជីថលផ្ទះបាយ
ចានលាយធំដែកអ៊ីណុក9
9
No bubbles, a plunger that floats
No bubbles, a plunger that floats
Air-pump tube dasher troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**William M. Wright** of Pittsburgh, Allegheny County, Pennsylvania, received US 6,711, dated 11 September 1849. The plunger was to be "specifically heavier than cream," or wood weighted with a plug of metal; the tub could be any pail, "particularly, if it be deep in comparison with its width." He claimed the combination of the loose plunger with the tubular dasher.
**Honest limits.** A pipe and printed parts stand in for his tinned sheet-iron tube; use a food-grade pipe. FDM prints hold food in their layer lines, so wash well and replace when worn. Your times and weights are the result.
សម្ភារៈ
10- 1 ដុំកន្លែងទុក
- 1 ដុំកន្លែងទុក
- 1 ដុំកន្លែងទុក
- 2 ដុំកន្លែងទុក
- 1 ដុំកន្លែងទុក
- 1 ដុំកន្លែងទុក
- 1 ដុំកន្លែងទុក
- 2000 មលកន្លែងទុក
- 1 ដុំកន្លែងទុក
- 1 ដុំកន្លែងទុក
ឧបករណ៍ចាំបាច់
8- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
ឯកសាររចនា
1ប្លង់ពាក់ព័ន្ធ
ប្លង់ទាំងនេះចែករំលែកចំណេះដឹង — បច្ចេកទេស សម្ភារៈ ឬគោលការណ៍
Air-Pump Annular Dasher Churn: A Pump in the Middle, a Ring Dasher Round It
ដោយ Martin
ម្ហូប និង ភេសជ្ជៈ
9
0
0
0
0
0
Trapped-Air Cylinder Dash Churn: A Hollow Dash That Squeezes Air Into the Cream
ដោយ Emma
ម្ហូប និង ភេសជ្ជៈ
5
0
0
0
0
0
Valveless Cone Air Dasher: A Hollow Cone and Four Tubes, Nothing to Wear Out
ដោយ YourGrandma
ម្ហូប និង ភេសជ្ជៈ
6
0
0
0
0
0
CC0 សាធារណៈ
ប្លង់នេះត្រូវបានចេញផ្សាយក្រោម CC0។ អ្នកមានសិទ្ធិចម្លង កែប្រែ ចែកចាយ និងប្រើប្រាស់ដោយមិនចាំបាច់សុំអនុញ្ញាត។
គាំទ្រអ្នកបង្កើតដោយទិញផលិតផលតាមរយៈប្លង់របស់ពួកគេ ដែលពួកគេទទួលបាន កម្រៃជើងសារអ្នកបង្កើត កំណត់ដោយអ្នកលក់ ឬបង្កើតកំណែថ្មីនៃប្លង់នេះ ហើយបញ្ចូលជាការតភ្ជាប់ក្នុងប្លង់របស់អ្នកដើម្បីចែករំលែកចំណូល។