កិច្ចសហប្រតិបត្តិការ
សិល្បៈ
សម្រស់ និង សុខុមាលភាព
សិប្បកម្ម
វប្បធម៌ និង ប្រវត្តិសាស្ត្រ
ការកម្សាន្ត
បរិស្ថាន
ម្ហូប និង ភេសជ្ជៈ
វិស្វកម្មបញ្ច្រាស
វិទ្យាសាស្ត្រ
កីឡា
បច្ចេកវិទ្យា
ប្រដាប់ដែលស្លៀក

Bench Glassblowing Torch: Brass Gas Blowpipe with a Glass Air Jet (Shenstone, 1916)
A glassblower's gas blowpipe you can make yourself: a brass tube with a side tube for gas, and a glass air jet down its middle fed from a foot-blower. A fine jet gives the small pointed flame for joints, and a wider jet the big brush flame for heating large tubes. It is pegged into a wooden block on a sheet-iron-covered bench, with taps for gas and air at the bench edge.
Result: a bench blowpipe for working glass tube. Make two: one about 11 mm bore for small work, one 15 to 17 mm for large.
Source: W. A. Shenstone, The Methods of Glass-Blowing (1916), pp. 3-9. Unknown: the brazing metal and the tap type. Picture: Fig. 1 of the book.
មធ្យម
Unknown
ការណែនាំ
1
1
Braze the gas inlet
Braze the gas inlet
Take a brass tube for the body: about 11 mm bore for the small blowpipe, 15 to 17 mm for the large one. Braze a side tube for the gas onto it 10 to 12 cm from the back end, according to the tube's size. Fix a spike to it for mounting. Ours: borax as the flux. Not given: the brazing metal.
សម្ភារៈសម្រាប់ជំហាននេះ៖
បំពង់លង្ហិន1 body and side tube
លោហៈមិនស្គាល់1 brazing metal and spike
ម្សៅបូរ៉ាក់1 brazing fluxឧបករណ៍ដែលត្រូវការ៖
រណារកាត់ដែក
ឡជាងដែក2
2
Fit the glass air jet
Fit the glass air jet
Fit a glass tube down the middle of the brass tube, held by a cork at the back end, its tip near the mouth. For the small pointed flame, draw the tip down to the size of a large knitting needle. For a large flame rich in air, the tip may be nearly half the bore of the brass tube. Make several air tubes of different sizes for each blowpipe.
សម្ភារៈសម្រាប់ជំហាននេះ៖
បំពង់កញ្ចក់3 air jets of several sizes
ឆ្នុកកូក1 jet corkឧបករណ៍ដែលត្រូវការ៖
ចង្ក្រានប៊ុនសែន3
3
Set up the bench
Set up the bench
Cover the bench round the blowpipe with sheet iron. Drill several holes in a block of wood so the spike can be set at different positions. Fix two taps near the bench edge, one for gas and one for air. Connect them by flexible tubes to the supplies on one side and to the blowpipe's gas inlet and air jet on the other. Ours: mild steel sheet, rubber tubing. Not given: the tap type.
សម្ភារៈសម្រាប់ជំហាននេះ៖
សន្លឹកដែកថែបទន់1 bench cover
ដុំឈើរឹង1 mounting block
វ៉ាល់មិនស្គាល់2 gas and air taps
បំពង់កៅស៊ូ1 flexible tubesឧបករណ៍ដែលត្រូវការ៖
ម៉ាស៊ីនចោះឈរ4
4
Light it and blow
Light it and blow
Light the gas at the mouth and work a foot-blower to drive air through the glass jet into the burning gas. Little air and a small jet give the pointed flame; plenty of gas and a strong blast give the large, non-luminous brush flame.
ឧបករណ៍ដែលត្រូវការ៖
ដង្កូវផ្លុំខ្យល់សម្ភារៈ
9- 1 body and side tubeកន្លែងទុក
- 1 brazing metal and spikeកន្លែងទុក
- 1 brazing fluxកន្លែងទុក
- 3 air jets of several sizesកន្លែងទុក
- 1 jet corkកន្លែងទុក
- 1 bench coverកន្លែងទុក
- 1 mounting blockកន្លែងទុក
- 2 gas and air tapsកន្លែងទុក
- 1 flexible tubesកន្លែងទុក
ឧបករណ៍ចាំបាច់
5- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
សម្ភារៈប្លង់ដែលបានភ្ជាប់

ចំណែក 10%
Venetian Borax: Refining Tincal with Lime
ដោយ Charlie
គ្មានកាបូន
23
0
0
0
1
0

ចំណែក 10%
Natural Rubber Tubing, Bands and Sheet: Sulfur-Cured with Heat
ដោយ Mary
រសាយនវិទ្យា
16
0
0
0
2
0

ចំណែក 10%
Oak Boards and Blocks, Milled and Air-Dried
ដោយ Woody
ការធ្វើការឈើ
46
0
0
0
3
0

ចំណែក 10%
Building a Box Bellows — The Breath That Makes Metal Obey Fire
ដោយ Emma
ការធ្វើការឈើ
109
0
0
0
8
0
ប្លង់នេះធ្វើ
CC0 សាធារណៈ
ប្លង់នេះត្រូវបានចេញផ្សាយក្រោម CC0។ អ្នកមានសិទ្ធិចម្លង កែប្រែ ចែកចាយ និងប្រើប្រាស់ដោយមិនចាំបាច់សុំអនុញ្ញាត។
គាំទ្រអ្នកបង្កើតដោយទិញផលិតផលតាមរយៈប្លង់របស់ពួកគេ ដែលពួកគេទទួលបាន កម្រៃជើងសារអ្នកបង្កើត កំណត់ដោយអ្នកលក់ ឬបង្កើតកំណែថ្មីនៃប្លង់នេះ ហើយបញ្ចូលជាការតភ្ជាប់ក្នុងប្លង់របស់អ្នកដើម្បីចែករំលែកចំណូល។
