កិច្ចសហប្រតិបត្តិការ
សិល្បៈ
សម្រស់ និង សុខុមាលភាព
សិប្បកម្ម
វប្បធម៌ និង ប្រវត្តិសាស្ត្រ
ការកម្សាន្ត
បរិស្ថាន
ម្ហូប និង ភេសជ្ជៈ
វិស្វកម្មបញ្ច្រាស
វិទ្យាសាស្ត្រ
កីឡា
បច្ចេកវិទ្យា
ប្រដាប់ដែលស្លៀក
Boring Bar: Driven Between Centres, with a Set-Screw Cutter (Yates, 1922)
Forge

បង្កើតដោយ

Forge

4. វិច្ឆិកា 2026NO
14
0
0
0
0

Boring Bar: Driven Between Centres, with a Set-Screw Cutter (Yates, 1922)

A home-made boring bar for holes too long for an ordinary boring tool, which would spring. A short, stiff bar runs between the lathe centres, driven by a dog, and carries a hardened tool-steel cutter locked in a cross-hole by a set screw. The work is bolted to the lathe carriage and fed past the turning cutter. Result: a boring bar, plus the small short-cut bar of Fig. 110. Source: R. F. Yates, Lathe Work for Beginners (1922), pp. 134-136. Unknown: bar diameter and set-screw size. Picture: Figs. 110-111 of the book.
មធ្យម
Unknown

ការណែនាំ

1

Turn the bar

Turn a bar no longer than the job needs; the shorter it is, the less it twists under the cut. Drill both ends for the lathe centres. For short cuts, the small bar of Fig. 110 is 4 to 6 inches long with a round shank and a squared end. Ours: mild steel round bar. Not given: the diameter.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ដែកថែបទន់មូលដែកថែបទន់មូល1 boring bar

ឧបករណ៍ដែលត្រូវការ៖

ម៉ាស៊ីនកាត់ដែក (ទ័រ)ម៉ាស៊ីនកាត់ដែក (ទ័រ)
វិមាត្រមិនស្គាល់វិមាត្រមិនស្គាល់
2

Fit the cutter and set screw

Drill a cross-hole through the bar for the cutter and drill and tap a hole into it for a set screw that locks the cutter. Make the cutter of tool steel, grind its point with proper clearance, and harden it.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ដែករបារឧបករណ៍ការ៉េដែករបារឧបករណ៍ការ៉េ1 cutter
លោហៈមិនស្គាល់លោហៈមិនស្គាល់1 set screw

ឧបករណ៍ដែលត្រូវការ៖

ម៉ាស៊ីនចោះឈរម៉ាស៊ីនចោះឈរ
ឈុតកាត់ខ្សែវីសឈុតកាត់ខ្សែវីស
ត្បាល់សំលៀងវិលត្បាល់សំលៀងវិល
ឡព្យាបាលដោយកំដៅឡព្យាបាលដោយកំដៅ
ធុងជ្រលក់ត្រជាក់ធុងជ្រលក់ត្រជាក់
3

Bore with it

Bolt the work down to the lathe carriage carefully and securely; carriage bolts of several sizes are handy for this. Drive the bar between centres with a dog and feed the carriage. Run very slowly when boring cast iron, and keep the feed light so the bar does not spring.

ឧបករណ៍ដែលត្រូវការ៖

ម៉ាស៊ីនកាត់ដែក (ទ័រ)ម៉ាស៊ីនកាត់ដែក (ទ័រ)
ប៊ូឡុងក្បាលមូលប៊ូឡុងក្បាលមូល

សម្ភារៈ

3

ឧបករណ៍ចាំបាច់

8

CC0 សាធារណៈ

ប្លង់នេះត្រូវបានចេញផ្សាយក្រោម CC0។ អ្នកមានសិទ្ធិចម្លង កែប្រែ ចែកចាយ និងប្រើប្រាស់ដោយមិនចាំបាច់សុំអនុញ្ញាត។

គាំទ្រអ្នកបង្កើតដោយទិញផលិតផលតាមរយៈប្លង់របស់ពួកគេ ដែលពួកគេទទួលបាន កម្រៃជើងសារអ្នកបង្កើត កំណត់ដោយអ្នកលក់ ឬបង្កើតកំណែថ្មីនៃប្លង់នេះ ហើយបញ្ចូលជាការតភ្ជាប់ក្នុងប្លង់របស់អ្នកដើម្បីចែករំលែកចំណូល។

ការពិភាក្សា

(0)

ចូល ដើម្បីចូលរួមពិភាក្សា

កំពុងផ្ទុកមតិ...