កិច្ចសហប្រតិបត្តិការ
សិល្បៈ
សម្រស់ និង សុខុមាលភាព
សិប្បកម្ម
វប្បធម៌ និង ប្រវត្តិសាស្ត្រ
ការកម្សាន្ត
បរិស្ថាន
ម្ហូប និង ភេសជ្ជៈ
វិស្វកម្មបញ្ច្រាស
វិទ្យាសាស្ត្រ
កីឡា
បច្ចេកវិទ្យា
ប្រដាប់ដែលស្លៀក
Ski Staff: Bamboo Pole With Wrist Loop, Wooden Snow Disk and Lead-Set Spike (Boy Mechanic, 1915)
Woody

បង្កើតដោយ

Woody

13. វិច្ឆិកា 2026NO
9
0
0
0
0

Ski Staff: Bamboo Pole With Wrist Loop, Wooden Snow Disk and Lead-Set Spike (Boy Mechanic, 1915)

A homemade ski staff from The Boy Mechanic, Book 2 (1915): a 4-1/2 ft bamboo pole with a leather wrist loop at the top, a 5 in pine disk 6 in above the tip to stop it sinking in deep snow, and a wire spike set in lead in a hardwood plug for icy ground.
ចាប់ផ្តើម
About 3 hours

ការណែនាំ

1

His sizes in centimetres

កំពុងផ្ទុកសៀវភៅ Jupyter…
2

Read The Boy Mechanic, Book 2

"A ski staff will greatly assist progress over level stretches and is an aid to the ski runner in preserving his balance."
3

Cut the staff and loop

Cut a bamboo pole 1-1/4 or 1-1/2 in in diameter and 4-1/2 ft long. Shave an old strap thinner, cut it about 1/2 in wide, and fix it as a narrow wrist loop at the top.

សម្ភារៈសម្រាប់ជំហាននេះ៖

បង្គោលឫស្សីបង្គោលឫស្សី1 ដុំ
ស្បែកគ្រឿងសេះស្បែកគ្រឿងសេះ1 ដុំ
គោលរីវេតស្ពាន់គោលរីវេតស្ពាន់1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

រណារដៃរណារដៃ
កាំបិតកាត់ស្បែកកាំបិតកាត់ស្បែក
ស្វានដៃស្វានដៃ
ញញួរញញួរ
ខ្សែវាស់ខ្សែវាស់
4

Make and fix the snow disk

Cut a disk of well-seasoned white pine or spruce, 1/2 in thick and 5 in in diameter, and coat it with shellac. Bore its centre to pass up the staff about 6 in. Fix it with two pieces of heavy wire: wire A goes through the staff below wire B and at right angles to it, so B must be bent over A. Staple both wires to the disk.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ក្តារឈើស្រល់ក្តារឈើស្រល់1 ដុំ
វ៉ានីសសែលឡាក់វ៉ានីសសែលឡាក់1 ដុំ
លួសដែកទាញលួសដែកទាញ1 ដុំ
ដែកកោងរាង U ពីលួសដែកកោងរាង U ពីលួស4 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

រណារកាត់ខ្សែកោងរណារកាត់ខ្សែកោង
ស្វាន់ដៃវិលមានក្បាលស្វាន់ដៃវិលមានក្បាល
ស្វានដៃស្វានដៃ
ដង្កាប់មាត់រាបដង្កាប់មាត់រាប
ញញួរញញួរ
ជក់លាបធំទូលាយជក់លាបធំទូលាយ
5

Set the spike

Plug the lower end with hard wood and bore part way into its centre for a wire spike. Cut slight recesses in the sides of the hole to anchor lead, and pour melted lead round the spike. Sharpen the point, then wind the bamboo with waxed twine or fine wire so it does not split.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ក្តារឈើរឹងក្តារឈើរឹង1 ដុំ
លួសដែកទាញលួសដែកទាញ1 ដុំ
ដុំចាក់សំណដុំចាក់សំណ1 ដុំ
ខ្សែធ្មៃខ្សែធ្មៃ1 ដុំ
ក្រមួនឃ្មុំក្រមួនឃ្មុំ1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

ស្វានដៃស្វានដៃ
ដែកឆូតឈើដែកឆូតឈើ
វែកលោហៈវែកលោហៈ
ចង្កៀងភ្លើងប្រូផានចង្កៀងភ្លើងប្រូផាន
ដែកឆាប (ដែកឆាបដៃ)ដែកឆាប (ដែកឆាបដៃ)
ដង្កាប់មាត់រាបដង្កាប់មាត់រាប
6

Troubleshooting

Ski staff troubleshooting.

Flow

Loading...
7

History and honest limits

From "How to Make a Ski Staff", in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, p. 51). No contributor is named. He gives no wire gauge or spike length. The tools and metric figures are ours.

សម្ភារៈ

11

ឧបករណ៍ចាំបាច់

13

ប្លង់ពាក់ព័ន្ធ

ប្លង់ទាំងនេះចែករំលែកចំណេះដឹង — បច្ចេកទេស សម្ភារៈ ឬគោលការណ៍

CC0 សាធារណៈ

ប្លង់នេះត្រូវបានចេញផ្សាយក្រោម CC0។ អ្នកមានសិទ្ធិចម្លង កែប្រែ ចែកចាយ និងប្រើប្រាស់ដោយមិនចាំបាច់សុំអនុញ្ញាត។

គាំទ្រអ្នកបង្កើតដោយទិញផលិតផលតាមរយៈប្លង់របស់ពួកគេ ដែលពួកគេទទួលបាន កម្រៃជើងសារអ្នកបង្កើត កំណត់ដោយអ្នកលក់ ឬបង្កើតកំណែថ្មីនៃប្លង់នេះ ហើយបញ្ចូលជាការតភ្ជាប់ក្នុងប្លង់របស់អ្នកដើម្បីចែករំលែកចំណូល។

ការពិភាក្សា

(0)

ចូល ដើម្បីចូលរួមពិភាក្សា

កំពុងផ្ទុកមតិ...