កិច្ចសហប្រតិបត្តិការ
សិល្បៈ
សម្រស់ និង សុខុមាលភាព
សិប្បកម្ម
វប្បធម៌ និង ប្រវត្តិសាស្ត្រ
ការកម្សាន្ត
បរិស្ថាន
ម្ហូប និង ភេសជ្ជៈ
វិស្វកម្មបញ្ច្រាស
វិទ្យាសាស្ត្រ
កីឡា
បច្ចេកវិទ្យា
ប្រដាប់ដែលស្លៀក
Homemade Wood Lathe: Hardwood Bed, Sliding Headstock and Tailstock, Steel Spindle With Stepped Pulley (Boy Mechanic, 1915)
Woody

បង្កើតដោយ

Woody

13. វិច្ឆិកា 2026NO
11
0
0
0
0

Homemade Wood Lathe: Hardwood Bed, Sliding Headstock and Tailstock, Steel Spindle With Stepped Pulley (Boy Mechanic, 1915)

E. E. Hulgan's lathe from The Boy Mechanic, Book 2 (1915), "in which wood and light metal articles may be turned": a 5 ft bed of two 2 by 4 in hardwood rails, a headstock clamped by bolts with a 3/4 in steel spindle in brass bearings and a three-step pulley, a bolted hardwood tailstock with a screw-fed dead centre, a sliding tool rest, and a screw-on chuck. Driven from a countershaft or by foot.
កម្រិតខ្ពស់
About 1-2 weeks

ការណែនាំ

1

His sizes, and the pulley speeds

កំពុងផ្ទុកសៀវភៅ Jupyter…
2

Read The Boy Mechanic, Book 2

"A strong, substantial lathe in which wood and light metal articles may be turned can be made by carefully following the description below and the detailed drawings of the parts."
3

Make the bed

Cut two pieces of straight-grained, smooth 2 by 4 in hardwood, 5 ft long, and hold them apart at each end with blocks of wood 2 in wide (Fig. 9 shows 2 in rails with a 2 in gap). The bed can be longer or shorter.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ក្តារឈើរឹងក្តារឈើរឹង2 ដុំ
វីសឈើវីសឈើ1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

រណារដៃរណារដៃ
កាំបិតឈូសឈើដៃកាំបិតឈូសឈើដៃ
ស្វានដៃស្វានដៃ
ខ្សែវាស់ខ្សែវាស់
4

Build the headstock frame

Make the two hardwood end pieces to the shape of Figs. 1 and 2 (2 in thick, 2 in apart on an 8 in base, 7-1/2 in high, 6 in wide at the bottom) and screw them to the base. Nail a slider 1 in thick and 10 in long, just wide enough to slide between the bed rails, under the base, 2 in from its rear end. Bore two 1/2 in holes through base and slider and put two 1/2 in bolts through them and through another slide and board under the bed, so tightening the nuts clamps the headstock. Screw a half-round wedge-shaped brace inside the frame against the front end.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ក្តារឈើរឹងក្តារឈើរឹង1 ដុំ
ប៊ូឡុងក្បាលមូលប៊ូឡុងក្បាលមូល2 ដុំ
ខ្ចៅប្រាំមួយជ្រុងខ្ចៅប្រាំមួយជ្រុង2 ដុំ
វីសឈើវីសឈើ1 ដុំ
ដែកគោលដែកគោល1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

រណារដៃរណារដៃ
ដែកឆូតឈើដែកឆូតឈើ
ស្វាន់ដៃវិលមានក្បាលស្វាន់ដៃវិលមានក្បាល
ស្វានដៃស្វានដៃ
5

Make the spindle and bearings

Make the spindle of tool steel or steel tubing, 3/4 in in diameter and 14 in long, and cut a thread on one end. Rivet on a hardened steel collar, 1/4 by 1-1/2 in, to turn against another collar of the same size on the headstock; screw a third collar to the rear end piece and fix a collar with a removable pin on the spindle, fitted to turn easily with no end play. Drill brass tubing for the spindle as bearings and wedge them into the headstock 6 in above the bed, in line; drill small oil holes from the top.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ដែកថែបឧបករណ៍ជាដុំមូលដែកថែបឧបករណ៍ជាដុំមូល1 ដុំ
បំពង់ដែករចនាសម្ព័ន្ធបំពង់ដែករចនាសម្ព័ន្ធ1 ដុំ
Shaft CollarShaft Collar4 ដុំ
ដែកគោលដែកថែបដែកគោលដែកថែប1 ដុំ
បំពង់លង្ហិនបំពង់លង្ហិន1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

រណារកាត់ដែករណារកាត់ដែក
ឈុតកាត់ខ្សែវីសឈុតកាត់ខ្សែវីស
ស្វានដៃស្វានដៃ
ដែកឆាប (ដែកឆាបដៃ)ដែកឆាប (ដែកឆាបដៃ)
ដង្កាប់តុដង្កាប់តុ
ញញួរញញួរ
6

Fit the stepped pulley

Make the pulleys 2 in wide, with the diameters on the drawing: 6, 4-1/2 and 3 in. Fasten them to the spindle with a removable pin. (Turned hardwood is our choice of material; he does not say.)

សម្ភារៈសម្រាប់ជំហាននេះ៖

ក្តារឈើរឹងក្តារឈើរឹង1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

រណារដៃរណារដៃ
ស្វាន់ដៃវិលមានក្បាលស្វាន់ដៃវិលមានក្បាល
ស្វានដៃស្វានដៃ
7

Make the chuck and centres

For the chuck (Fig. 3), take shafting 1-1/2 in in diameter and 2-1/2 in long, drill a 1/2 in hole through its centre, ream and thread one end to fit the spindle, and fit a setscrew over the 1/2 in hole. Make a wood-turning centre, and other centres and drills, from 1/2 in tool steel.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ដែកថែបទន់មូលដែកថែបទន់មូល1 ដុំ
ដែកថែបឧបករណ៍ជាដុំមូលដែកថែបឧបករណ៍ជាដុំមូល1 ដុំ
វីសរឹតក្បាលរូងចានវីសរឹតក្បាលរូងចាន1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

រណារកាត់ដែករណារកាត់ដែក
ស្វានដៃស្វានដៃ
ដែកពង្រីករន្ធដែកពង្រីករន្ធ
ឈុតកាត់ខ្សែវីសឈុតកាត់ខ្សែវីស
ដែកឆាប (ដែកឆាបដៃ)ដែកឆាប (ដែកឆាបដៃ)
ដង្កាប់តុដង្កាប់តុ
8

Build the tailstock

Build the tailstock (Figs. 4-6) of three pieces of hardwood 2 in thick and one 1 in thick, shaped as drawn, held together with four bolts 7-1/2 in long. Give it sliders and clamp it to the bed like the headstock, but with one bolt, and weld a handle to its nut for easy clamping. Drill a piece of tubing 2 in long for a 1/2 in dead centre and set it 1-1/2 in into the joint between the two upper pieces. Bore for a 1/2 in bolt to slide in the tube; chisel a recess behind the tube for a 1/2 in nut; turn a bolt 7 in long, threaded for 2 in, into nut and tube, and rivet a handle or wheel on its end. Make the centre of 1/2 in tool steel with a tapered point.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ក្តារឈើរឹងក្តារឈើរឹង2 ដុំ
ប៊ូឡុងក្បាលមូលប៊ូឡុងក្បាលមូល5 ដុំ
ខ្ចៅប្រាំមួយជ្រុងខ្ចៅប្រាំមួយជ្រុង2 ដុំ
បំពង់ដែករចនាសម្ព័ន្ធបំពង់ដែករចនាសម្ព័ន្ធ1 ដុំ
ដែកថែបឧបករណ៍ជាដុំមូលដែកថែបឧបករណ៍ជាដុំមូល1 ដុំ
ដែកគោលដែកថែបដែកគោលដែកថែប1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

រណារដៃរណារដៃ
ដែកឆូតឈើដែកឆូតឈើ
ស្វាន់ដៃវិលមានក្បាលស្វាន់ដៃវិលមានក្បាល
ស្វានដៃស្វានដៃ
ឡធ្យូងថ្មឡធ្យូងថ្ម
ទាំងជល់ (កំណាត់ដែក)ទាំងជល់ (កំណាត់ដែក)
ញញួរជាងដែកញញួរជាងដែក
ដែកឆាប (ដែកឆាបដៃ)ដែកឆាប (ដែកឆាបដៃ)
9

Make the tool rest

The tool rest (Figs. 7-9) has a slide 3/4 by 3 by 13 in with a slot 1/2 by 6 in. Bolt the rest base on the slide so it can be adjusted, and screw the rest to the base. Raise or lower it with wedges between slide and base, and clamp it to the bed like the tailstock.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ក្តារឈើរឹងក្តារឈើរឹង1 ដុំ
ប៊ូឡុងក្បាលមូលប៊ូឡុងក្បាលមូល1 ដុំ
ខ្ចៅប្រាំមួយជ្រុងខ្ចៅប្រាំមួយជ្រុង1 ដុំ
វីសឈើវីសឈើ1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

រណារដៃរណារដៃ
ដែកឆូតឈើដែកឆូតឈើ
ស្វាន់ដៃវិលមានក្បាលស្វាន់ដៃវិលមានក្បាល
10

Troubleshooting

Wood lathe troubleshooting.

Flow

Loading...
11

History and honest limits

From "How to Make a Wood Lathe" by E. E. Hulgan, Marion, Ind., in **The Boy Mechanic, Book 2**, Popular Mechanics, 1915 (Project Gutenberg 44585; checked on the archive.org scan boymechanicbook200chic2, pp. 434-436). Part shapes come from his Figs. 1-9; he gives no pulley material and no countershaft or foot-drive details. The pulley material, tools and metric figures are ours.

សម្ភារៈ

12

ឧបករណ៍ចាំបាច់

15

ប្លង់ពាក់ព័ន្ធ

ប្លង់ទាំងនេះចែករំលែកចំណេះដឹង — បច្ចេកទេស សម្ភារៈ ឬគោលការណ៍

CC0 សាធារណៈ

ប្លង់នេះត្រូវបានចេញផ្សាយក្រោម CC0។ អ្នកមានសិទ្ធិចម្លង កែប្រែ ចែកចាយ និងប្រើប្រាស់ដោយមិនចាំបាច់សុំអនុញ្ញាត។

គាំទ្រអ្នកបង្កើតដោយទិញផលិតផលតាមរយៈប្លង់របស់ពួកគេ ដែលពួកគេទទួលបាន កម្រៃជើងសារអ្នកបង្កើត កំណត់ដោយអ្នកលក់ ឬបង្កើតកំណែថ្មីនៃប្លង់នេះ ហើយបញ្ចូលជាការតភ្ជាប់ក្នុងប្លង់របស់អ្នកដើម្បីចែករំលែកចំណូល។

ការពិភាក្សា

(0)

ចូល ដើម្បីចូលរួមពិភាក្សា

កំពុងផ្ទុកមតិ...