កិច្ចសហប្រតិបត្តិការ
សិល្បៈ
សម្រស់ និង សុខុមាលភាព
សិប្បកម្ម
វប្បធម៌ និង ប្រវត្តិសាស្ត្រ
ការកម្សាន្ត
បរិស្ថាន
ម្ហូប និង ភេសជ្ជៈ
វិស្វកម្មបញ្ច្រាស
វិទ្យាសាស្ត្រ
កីឡា
បច្ចេកវិទ្យា
ប្រដាប់ដែលស្លៀក
Canteen From Two Pie Plates: Rims Soldered Together, a Screw-Cap Neck in the Edge (Boy Mechanic, 1919)
Tinny

បង្កើតដោយ

Tinny

13. វិច្ឆិកា 2026US
9
0
0
0
0

Canteen From Two Pie Plates: Rims Soldered Together, a Screw-Cap Neck in the Edge (Boy Mechanic, 1919)

A canteen "for the camper or hiker", sent to The Boy Mechanic (1919) by J. R. Townsend of Itasca, Texas: two nickel-plated pie plates soldered rim to rim, the screw-capped neck of a metal-polish can soldered over an opening in the edge, and two wire loops for the snap hooks of a shoulder strap. The book gives no sizes: the plates set the size.
ចាប់ផ្តើម
About 2 hours

ការណែនាំ

1

Read The Boy Mechanic

"Two good-quality pie plates were soldered at their edges to form a water-tight container." (J. R. Townsend, Itasca, Texas.)
2

Solder the plates together

Take two good-quality nickel-plated pie plates of the same size. Clean the rims, set them face to face, and solder them together all round the edge so the joint is water-tight. Use lead-free solder: this holds drinking water (our choice; the book only says solder).

សម្ភារៈសម្រាប់ជំហាននេះ៖

ចានដុតនំប៉ាយចានដុតនំប៉ាយ2 ដុំ
ផ្សារទុយោគ្មានសំណផ្សារទុយោគ្មានសំណ1 ដុំ
ហ្វ្លុចហ្វ្លុច1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

ដែកផ្សារសំណអគ្គិសនីដែកផ្សារសំណអគ្គិសនី
ដែកឆាបលោហៈដែកឆាបលោហៈ
3

Cut the neck off the can

Take a small metal-polish can with a screw cap. As the book's drawing shows, cut off its sloping top with the threaded neck, and trim the cut edge.

សម្ភារៈសម្រាប់ជំហាននេះ៖

កំប៉ុងសំណប៉ាហាំងកំប៉ុងសំណប៉ាហាំង1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

កន្ត្រៃកាត់លោហៈធ្ងន់កន្ត្រៃកាត់លោហៈធ្ងន់
ដែកឆាបលោហៈដែកឆាបលោហៈ
4

Cut the opening and fit the neck

Cut an opening in the edge of the canteen to suit the neck. Fit the neck carefully over it and solder it all round.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ផ្សារទុយោគ្មានសំណផ្សារទុយោគ្មានសំណ1 ដុំ
ហ្វ្លុចហ្វ្លុច1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

ស្វានដៃស្វានដៃ
ដែកឆាបលោហៈដែកឆាបលោហៈ
ដែកផ្សារសំណអគ្គិសនីដែកផ្សារសំណអគ្គិសនី
5

Solder on the strap loops

Bend two short pieces of wire into loops and solder one at each side of the screw cap, as loops for the snap hooks of the shoulder strap.

សម្ភារៈសម្រាប់ជំហាននេះ៖

លួសដែកទាញលួសដែកទាញ1 ដុំ
ផ្សារទុយោគ្មានសំណផ្សារទុយោគ្មានសំណ1 ដុំ
ហ្វ្លុចហ្វ្លុច1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

ដង្កាប់មាត់រាបដង្កាប់មាត់រាប
ដែកផ្សារសំណអគ្គិសនីដែកផ្សារសំណអគ្គិសនី
6

Fit the strap and test

Put a snap hook on each end of a shoulder strap and hook them into the loops. Fill the canteen with water, screw on the cap and check every joint for leaks (our test), then rinse it before use.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ខ្សែស្បែកខ្សែស្បែក1 ដុំ
ទំពក់ស្ព្រីងទំពក់ស្ព្រីង2 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

ទឹកសាបទឹកសាប
7

Troubleshooting

Canteen troubleshooting.

Flow

Loading...
8

History and honest limits

From **The Boy Mechanic, Book 3**, edited by H. H. Windsor, Popular Mechanics, Chicago, 1919 (Project Gutenberg 71856), "How to Make a Canteen", sent in by J. R. Townsend of Itasca, Texas. The book gives no sizes and names no tools; the lead-free solder, the tools, the strap material and the leak test are ours.

សម្ភារៈ

7

ឧបករណ៍ចាំបាច់

6

ប្លង់ពាក់ព័ន្ធ

ប្លង់ទាំងនេះចែករំលែកចំណេះដឹង — បច្ចេកទេស សម្ភារៈ ឬគោលការណ៍

CC0 សាធារណៈ

ប្លង់នេះត្រូវបានចេញផ្សាយក្រោម CC0។ អ្នកមានសិទ្ធិចម្លង កែប្រែ ចែកចាយ និងប្រើប្រាស់ដោយមិនចាំបាច់សុំអនុញ្ញាត។

គាំទ្រអ្នកបង្កើតដោយទិញផលិតផលតាមរយៈប្លង់របស់ពួកគេ ដែលពួកគេទទួលបាន កម្រៃជើងសារអ្នកបង្កើត កំណត់ដោយអ្នកលក់ ឬបង្កើតកំណែថ្មីនៃប្លង់នេះ ហើយបញ្ចូលជាការតភ្ជាប់ក្នុងប្លង់របស់អ្នកដើម្បីចែករំលែកចំណូល។

ការពិភាក្សា

(0)

ចូល ដើម្បីចូលរួមពិភាក្សា

កំពុងផ្ទុកមតិ...