កិច្ចសហប្រតិបត្តិការ
សិល្បៈ
សម្រស់ និង សុខុមាលភាព
សិប្បកម្ម
វប្បធម៌ និង ប្រវត្តិសាស្ត្រ
ការកម្សាន្ត
បរិស្ថាន
ម្ហូប និង ភេសជ្ជៈ
វិស្វកម្មបញ្ច្រាស
វិទ្យាសាស្ត្រ
កីឡា
បច្ចេកវិទ្យា
ប្រដាប់ដែលស្លៀក

Brazing Torch: a Pressure-Tank Gasoline or Kerosene Torch (Shop Notes, 1909)
A shop brazing and tempering torch: a wall-hung pipe tank of gasoline or kerosene pumped up with a bicycle pump, feeding a 1/8 in pipe whose end is coiled round a short 1 in pipe; the flame heats the coil, the oil turns to gas, and it blasts out through a pinhole cap.
Two burners on a tee give a bigger heat.
Source: Popular Mechanics Shop Notes for 1909, pp. 861-862. Picture: the article's drawing.
មធ្យម
Unknown
ការណែនាំ
1
1
Make the tank
Make the tank
Cap both ends of a 2 in pipe 20 in long. Drill three holes in the top cap: one for the rubber tube from a bicycle pump, one for a steam gauge, and one with a screw plug for filling with fuel oil.
សម្ភារៈសម្រាប់ជំហាននេះ៖
បំពង់ដែក (ជញ្ជាំងក្រាស់ ចុងមានខ្សែវីស)1 2 in x 20 in
គ្រឿងតភ្ជាប់បំពង់មានខ្សែវីស3 two caps, plug
ឧបករណ៍វាស់សម្ពាធ1 ដុំ
បំពង់កៅស៊ូ1 ដុំឧបករណ៍ដែលត្រូវការ៖
ស្វានដៃ
ឈុតកាត់ខ្សែវីស
សោរបំពង់
ស្នប់ខ្យល់ឈរសម្រាប់កង់2
2
Coil the burner
Coil the burner
Drill the bottom cap and connect a 1/8 in pipe D, any length, with a globe valve in it to set and shut off the oil. Fill the last 10 in of the pipe with lead, coil it round a 1 in pipe F 6 in long, and turn the end out to take two elbows and a short nipple; then melt the lead out. Drill a small hole in the centre of a 1/8 in cap and fit it on the end (E) so the hole lines up with the centre of pipe F.
សម្ភារៈសម្រាប់ជំហាននេះ៖
បំពង់ដែក (ជញ្ជាំងក្រាស់ ចុងមានខ្សែវីស)1 1/8 in, and 1 in x 6 in
គ្រឿងតភ្ជាប់បំពង់មានខ្សែវីស4 two elbows, nipple, 1/8 in cap
វ៉ាល់មូល1 ដុំឧបករណ៍ដែលត្រូវការ៖
សំណ
វែកមានរន្ធ
ឡជាងដែក
ស្វានដៃ
សោរបំពង់3
3
Start the burner
Start the burner
Hang a little cup holding three or four teaspoonfuls of oil just below the coil and light it to heat the coil; then pump up the tank and open the globe valve. For more heat connect two burners on a tee so their blasts meet.
ឧបករណ៍ដែលត្រូវការ៖
ប្រេងកាត
ស្នប់ខ្យល់ឈរសម្រាប់កង់សម្ភារៈ
5- 1 1/8 in, and 1 in x 6 inកន្លែងទុក
- 4 two elbows, nipple, 1/8 in capកន្លែងទុក
- 1 ដុំកន្លែងទុក
- 1 ដុំកន្លែងទុក
- 1 ដុំកន្លែងទុក
ប្លង់នេះធ្វើ
CC0 សាធារណៈ
ប្លង់នេះត្រូវបានចេញផ្សាយក្រោម CC0។ អ្នកមានសិទ្ធិចម្លង កែប្រែ ចែកចាយ និងប្រើប្រាស់ដោយមិនចាំបាច់សុំអនុញ្ញាត។
គាំទ្រអ្នកបង្កើតដោយទិញផលិតផលតាមរយៈប្លង់របស់ពួកគេ ដែលពួកគេទទួលបាន កម្រៃជើងសារអ្នកបង្កើត កំណត់ដោយអ្នកលក់ ឬបង្កើតកំណែថ្មីនៃប្លង់នេះ ហើយបញ្ចូលជាការតភ្ជាប់ក្នុងប្លង់របស់អ្នកដើម្បីចែករំលែកចំណូល។
