កិច្ចសហប្រតិបត្តិការ
សិល្បៈ
សម្រស់ និង សុខុមាលភាព
សិប្បកម្ម
វប្បធម៌ និង ប្រវត្តិសាស្ត្រ
ការកម្សាន្ត
បរិស្ថាន
ម្ហូប និង ភេសជ្ជៈ
វិស្វកម្មបញ្ច្រាស
វិទ្យាសាស្ត្រ
កីឡា
បច្ចេកវិទ្យា
ប្រដាប់ដែលស្លៀក
Rack-and-Pawl Plunge Router: The Motor Rides One Post on a Spring and Steps Down a Tooth at a Time (Carter, 1925)
Forge

បង្កើតដោយ

Forge

13. វិច្ឆិកា 2026NO
15
0
0
0
0

Rack-and-Pawl Plunge Router: The Motor Rides One Post on a Spring and Steps Down a Tooth at a Time (Carter, 1925)

Ray L. Carter of Syracuse, New York, improved his 1924 router with US 1,565,790, dated 15 December 1925. The motor's holder now slides up and down a single strong post on a large round base, and a spring inside the post holds it up off the work. Each press of a lever moves the holder down one tooth of a rack, so a deep cavity is cut in stages. A locking pawl holds each step. Gauge nuts on a plunger stem set the final depth, and pressing the pawl's foot lets the spring lift the cutter clear. We reuse our 1924 router's printed motor casing in a printed holder on a square steel post. The sizes are ours.
កម្រិតខ្ពស់
About 3 days

ការណែនាំ

1

Cutting deep in stages

កំពុងផ្ទុកសៀវភៅ Jupyter…
2

Read US 1,565,790

"By this arrangement cavities of considerable depth may be routed by successive stages wherein each stage represents the normal depth the tool is designed to cut."
3

The motor and its casing come from the 1924 router

Print the casing and fit the motor, collet and switch exactly as in Carter's 1924 router; here the casing screws into a holder on a post instead of into a base.
4

Print the holder

The holder 7: a split ring threaded for the 1924 casing, clamp lugs for a thumb screw, and beside it the guide 7c with a square opening for a 1 in tube, a recess for the gib plate, two set-screw holes and the rack 17 of 3 mm teeth on its outer face. Print it rack upright. PETG, 0.2 mm layers, 40 % infill, 5 walls; no supports.
ឯកសាររចនាSTLCC0 - Free
5

Print the base

The base 9: a round plate 170 mm across with a 50 mm opening, and the boss 9' with a square socket for the post and a hole for its cross bolt. Print it plate down. PETG, 0.2 mm layers, 40 % infill, 5 walls; no supports.
ឯកសាររចនាSTLCC0 - Free
6

The hollow post 8

Cut 1 inch square steel tube 200 mm long. Saw and file a slot 8b 6 mm wide and 100 mm long down the middle of one wall, starting 40 mm from the top. Push the post into the base's socket and bolt it through with an M6 bolt and lock nut. Drop a compression spring 10 into the post, then a plunger 13: a block of flat bar that slides in the tube, tapped M6 on its back for the screw that runs in the slot, with an M6 rod 13' standing up from it. Screw a flat-bar cap 12 across the post's top with a hole for the rod, and run two gauge nuts 14, 14' onto the rod above it.

សម្ភារៈសម្រាប់ជំហាននេះ៖

Mild Steel Square Tube 1" x 1"Mild Steel Square Tube 1" x 1"1 ដុំ
ដែកបន្ទះរាបថែបទន់ដែកបន្ទះរាបថែបទន់1 ដុំ
សំណុំរ៉ឺស័របង្ហាប់សំណុំរ៉ឺស័របង្ហាប់1 ដុំ
ដងវីស (ដងខ្សែវីស)ដងវីស (ដងខ្សែវីស)1 ដុំ
ខ្ចៅប្រាំមួយជ្រុងខ្ចៅប្រាំមួយជ្រុង2 ដុំ
ការប្រមូលផ្ដុំប៊ូឡុងប្រាំមួយជ្រុងការប្រមូលផ្ដុំប៊ូឡុងប្រាំមួយជ្រុង3 ដុំ
ខ្ចៅចាក់សោមានណៃឡុងខ្ចៅចាក់សោមានណៃឡុង1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

រណារកាត់ដែករណារកាត់ដែក
សំណុំដែកឆាបសំណុំដែកឆាប
ដង្កាប់តុដង្កាប់តុ
ម៉ាស៊ីនចោះឈរម៉ាស៊ីនចោះឈរ
សំណុំក្បាលខួងសំណុំក្បាលខួង
ឈុតកាត់ខ្សែវីសឈុតកាត់ខ្សែវីស
ដងបង្វិលដែកកាត់ខ្សែវីសខាងក្នុងដងបង្វិលដែកកាត់ខ្សែវីសខាងក្នុង
សោរបង្វិលកែតម្រូវបានសោរបង្វិលកែតម្រូវបាន
វ៉ែនតាសុវត្ថិភាពវ៉ែនតាសុវត្ថិភាព
7

Holder on the post

Print the holder and base. Lay a strip of flat bar in the guide's recess 15 as the gib plate 15' and run two M5 set screws 16 against it, one with a wing nut on its head to lock the holder by hand. Slide the guide down over the post and fix it to the plunger with an M6 screw through the slot. Set the screws so the holder slides freely without rattling. Screw the 1924 motor casing into the holder and lock it with an M5 screw and wing nut through the lugs.

សម្ភារៈសម្រាប់ជំហាននេះ៖

សរសៃ PETGសរសៃ PETG1 ដុំ
ដែកបន្ទះរាបថែបទន់ដែកបន្ទះរាបថែបទន់1 ដុំ
វីសរឹតក្បាលរូងចានវីសរឹតក្បាលរូងចាន2 ដុំ
ខ្ចៅស្លាបមេអំបៅខ្ចៅស្លាបមេអំបៅ2 ដុំ
វីសក្បាលរន្ធប្រាំមួយជ្រុងវីសក្បាលរន្ធប្រាំមួយជ្រុង2 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

ម៉ាស៊ីនបោះពុម្ព 3D ប្រើខ្សែ (FDM)ម៉ាស៊ីនបោះពុម្ព 3D ប្រើខ្សែ (FDM)
ឧបករណ៍ដកសំណល់គែមឧបករណ៍ដកសំណល់គែម
សំណុំកូនសោប្រាំមួយជ្រុងសំណុំកូនសោប្រាំមួយជ្រុង
ជញ្ជីងវាស់ឌីជីថល ៦ អ៊ីញជញ្ជីងវាស់ឌីជីថល ៦ អ៊ីញ
8

Pawls and lever

File a pawl 18 from flat bar with a hook 18' at its top to catch the rack's teeth, and a locking pawl 20 with a tooth 20' at its top and its lower end bent out as a foot 20d. Pivot the locking pawl on the base's boss with an M5 screw, held against the rack by a spring-steel leaf 20b. Pivot one end of a lever 19 on the boss and the pawl's lower end to the lever partway along, with a second leaf 20c holding the pawl to the rack. Each press of the lever's handle pulls the holder down one tooth, and the locking pawl drops in under it.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ដែកបន្ទះរាបថែបទន់ដែកបន្ទះរាបថែបទន់2 ដុំ
បន្ទះដែកស្ព្រីងបន្ទះដែកស្ព្រីង1 ដុំ
វីសក្បាលរន្ធប្រាំមួយជ្រុងវីសក្បាលរន្ធប្រាំមួយជ្រុង3 ដុំ
ខ្ចៅចាក់សោមានណៃឡុងខ្ចៅចាក់សោមានណៃឡុង3 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

រណារកាត់ដែករណារកាត់ដែក
សំណុំដែកឆាបសំណុំដែកឆាប
ដង្កាប់តុដង្កាប់តុ
ម៉ាស៊ីនចោះឈរម៉ាស៊ីនចោះឈរ
សំណុំក្បាលខួងសំណុំក្បាលខួង
សោរបង្វិលកែតម្រូវបានសោរបង្វិលកែតម្រូវបាន
9

Rout a deep recess

Fit a straight bit. Set the gauge nuts so the plunger's rod stops on the cap at the depth wanted. Clamp a board, rest the base on it with the cutter clear, switch on, press the lever once and move the router across the area; press again and repeat, until the nuts stop it. Press the locking pawl's foot and the spring lifts the cutter out.

ឧបករណ៍ដែលត្រូវការ៖

សំណុំក្បាលម៉ាស៊ីនឆូតសំណុំក្បាលម៉ាស៊ីនឆូត
ក្តារឈើរឹងក្តារឈើរឹង
ឈ្នាប់ដងវែងឈ្នាប់ដងវែង
វ៉ែនតាសុវត្ថិភាពវ៉ែនតាសុវត្ថិភាព
10

Troubleshooting

Plunge router troubleshooting.

Flow

Loading...
11

History and honest limits

**Ray L. Carter** of Syracuse, New York, US 1,565,790, dated 15 December 1925, filed 21 March 1925, improving his US 1,514,894. He describes a holder "formed at one side with a guide portion having an angular vertical opening, for slidably mounting the holder upon a pedestal or post of substantially the same angularity", a coil spring housed in the pedestal, a ratchet rack and pawl to move the motor step by step, a locking pawl, gauge nuts, and a plate with set screws to take up wear. His post is triangular and cast; ours is 1 inch square steel tube. His holder and base are metal; ours are printed PETG. His motor ran on mains; ours is the small DC motor of our 1924 router. The sizes are ours.

សម្ភារៈ

12

ឧបករណ៍ចាំបាច់

16

ឯកសាររចនា

2

ប្លង់ពាក់ព័ន្ធ

ប្លង់ទាំងនេះចែករំលែកចំណេះដឹង — បច្ចេកទេស សម្ភារៈ ឬគោលការណ៍

CC0 សាធារណៈ

ប្លង់នេះត្រូវបានចេញផ្សាយក្រោម CC0។ អ្នកមានសិទ្ធិចម្លង កែប្រែ ចែកចាយ និងប្រើប្រាស់ដោយមិនចាំបាច់សុំអនុញ្ញាត។

គាំទ្រអ្នកបង្កើតដោយទិញផលិតផលតាមរយៈប្លង់របស់ពួកគេ ដែលពួកគេទទួលបាន កម្រៃជើងសារអ្នកបង្កើត កំណត់ដោយអ្នកលក់ ឬបង្កើតកំណែថ្មីនៃប្លង់នេះ ហើយបញ្ចូលជាការតភ្ជាប់ក្នុងប្លង់របស់អ្នកដើម្បីចែករំលែកចំណូល។

ការពិភាក្សា

(0)

ចូល ដើម្បីចូលរួមពិភាក្សា

កំពុងផ្ទុកមតិ...