កិច្ចសហប្រតិបត្តិការ
សិល្បៈ
សម្រស់ និង សុខុមាលភាព
សិប្បកម្ម
វប្បធម៌ និង ប្រវត្តិសាស្ត្រ
ការកម្សាន្ត
បរិស្ថាន
ម្ហូប និង ភេសជ្ជៈ
វិស្វកម្មបញ្ច្រាស
វិទ្យាសាស្ត្រ
កីឡា
បច្ចេកវិទ្យា
ប្រដាប់ដែលស្លៀក
The Clearance Hole: Why the Bolt Should Not Touch the Top Part
បានបកប្រែ
Forge

បង្កើតដោយ

Forge

24. កញ្ញា 2026NO
79
0
0
0
0

The Clearance Hole: Why the Bolt Should Not Touch the Top Part

When a bolt clamps two parts together, only the far part should be threaded. The near part gets a CLEARANCE hole — a plain hole slightly bigger than the bolt, which the bolt passes through without touching. Skipping it ruins the joint. A bolt threaded into both parts cannot pull them together: it jacks against the top part's threads and the parts stay apart no matter how hard it is tightened. The same logic runs through countersinking, counterboring and wood screws — the top part must always be free to be pulled down.
មធ្យម
2 hours

ការណែនាំ

1

Why a bolt threaded into both parts cannot clamp

Picture two plates with a threaded hole through both, and a bolt wound into them. As the bolt turns it advances through BOTH sets of threads at the same rate. Nothing moves relative to anything: the gap between the plates never closes. Clamping force comes from stretching the bolt between the head and the threads it is engaged in. That needs the top part to be able to slide along the shank, which it cannot do if it is threaded. Test it once and it is unforgettable. Two plates with a gap between them and one threaded pair of holes: tighten hard, and the gap does not close. Drill the top one out to clearance and the bolt pulls the plates together.

សម្ភារៈសម្រាប់ជំហាននេះ៖

បន្ទះដែកថែបទន់បន្ទះដែកថែបទន់2 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

សំណុំក្បាលខួងសំណុំក្បាលខួង
ការប្រមូលផ្ដុំប៊ូឡុងប្រាំមួយជ្រុងការប្រមូលផ្ដុំប៊ូឡុងប្រាំមួយជ្រុង
សំណុំកូនសោសំណុំកូនសោ
2

How much clearance, and the three standard fits

CLOSE (fine) fit: an M6 in a 6.4 mm hole, 0.4 mm over the bolt. It locates the parts precisely and demands accurate hole positions. NORMAL (medium) fit: M6 in 6.6 mm, 0.6 mm over. This is the everyday default and absorbs ordinary marking-out error. LOOSE (coarse) fit: M6 in 7.0 mm, 1 mm over, for assemblies where the holes cannot be positioned accurately. These three sizes are the fine, medium and coarse series of ISO 273. Choose deliberately, because the clearance hole is where you decide how much adjustment the assembly will have. Too tight and the parts fight you; too loose and nothing lines up where you intended.

សម្ភារៈសម្រាប់ជំហាននេះ៖

បន្ទះដែកថែបទន់បន្ទះដែកថែបទន់1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

សំណុំក្បាលខួងសំណុំក្បាលខួង
ខ្នាតវ៉ែនញ្ញេខ្នាតវ៉ែនញ្ញេ
ការប្រមូលផ្ដុំប៊ូឡុងប្រាំមួយជ្រុងការប្រមូលផ្ដុំប៊ូឡុងប្រាំមួយជ្រុង
3

Countersink, counterbore, and getting the depth right

កំពុងផ្ទុកសៀវភៅ Jupyter…

ឧបករណ៍ដែលត្រូវការ៖

ឈុតក្បាលស្វានពង្រីកមាត់រន្ធឈុតក្បាលស្វានពង្រីកមាត់រន្ធ
ម៉ាស៊ីនគិតលេខម៉ាស៊ីនគិតលេខ
ខ្នាតវ៉ែនញ្ញេខ្នាតវ៉ែនញ្ញេ
4

The same rule in wood: the shank hole

A wood screw needs two holes, not one: a PILOT hole in the lower piece that the thread bites into, and a SHANK hole in the upper piece that the thread passes through freely. It is the identical principle. A screw whose thread grips the top piece jacks the two apart instead of pulling them together, and in wood this leaves a visible gap in the joint that no amount of driving will close. Modern screws with an unthreaded upper shank do the same job by being shaped for it. In hardwood the pilot hole also stops the screw splitting the piece, and near an end grain edge it is not optional at all. Match the pilot to the screw's root diameter — not its outside diameter — and the thread has full material to bite.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ក្តារឈើរឹងក្តារឈើរឹង2 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

សំណុំក្បាលខួងសំណុំក្បាលខួង
ឈុតទួណឺវីសឈុតទួណឺវីស
ឈុតក្បាលស្វានពង្រីកមាត់រន្ធឈុតក្បាលស្វានពង្រីកមាត់រន្ធ

សម្ភារៈ

2

ឧបករណ៍ចាំបាច់

7

CC0 សាធារណៈ

ប្លង់នេះត្រូវបានចេញផ្សាយក្រោម CC0។ អ្នកមានសិទ្ធិចម្លង កែប្រែ ចែកចាយ និងប្រើប្រាស់ដោយមិនចាំបាច់សុំអនុញ្ញាត។

គាំទ្រអ្នកបង្កើតដោយទិញផលិតផលតាមរយៈប្លង់របស់ពួកគេ ដែលពួកគេទទួលបាន កម្រៃជើងសារអ្នកបង្កើត កំណត់ដោយអ្នកលក់ ឬបង្កើតកំណែថ្មីនៃប្លង់នេះ ហើយបញ្ចូលជាការតភ្ជាប់ក្នុងប្លង់របស់អ្នកដើម្បីចែករំលែកចំណូល។

ការពិភាក្សា

(0)

ចូល ដើម្បីចូលរួមពិភាក្សា

កំពុងផ្ទុកមតិ...