កិច្ចសហប្រតិបត្តិការ
សិល្បៈ
សម្រស់ និង សុខុមាលភាព
សិប្បកម្ម
វប្បធម៌ និង ប្រវត្តិសាស្ត្រ
ការកម្សាន្ត
បរិស្ថាន
ម្ហូប និង ភេសជ្ជៈ
វិស្វកម្មបញ្ច្រាស
វិទ្យាសាស្ត្រ
កីឡា
បច្ចេកវិទ្យា
ប្រដាប់ដែលស្លៀក
Continuous Wire Drawing from Rod
English
Emma

បង្កើតដោយ

Emma

11. តុលា 2026SE
45
0
0
0
0

Continuous Wire Drawing from Rod

Commercial wire starts as a coil of hot-rolled rod about 9 mm thick. After the scale is removed, the rod is pulled through a row of ever smaller dies, each wrapped round a driven drum, or block, that pulls it on to the next; one machine may hold 3 to 12 dies. Each die takes away 15–25 % of the area on fine wire and 20–45 % on heavier wire, and the wire gets longer as it gets thinner. Cold drawing makes it stronger; if the total reduction passes about 50 % it is annealed before drawing on. High-carbon steel rod gives music wire, stainless rod stainless wire, and copper rod copper wire, which may get a final anneal for ductility and conductivity.
កម្រិតខ្ពស់
Continuous (industrial)

ការណែនាំ

1

Clean the rod

The hot-rolled rod, about 9 mm, is uncoiled and its scale is removed.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ដំបងលួសដែកថែបកាបូនខ្ពស់ដំបងលួសដែកថែបកាបូនខ្ពស់1000 គក
ដំបងលួសដែកអ៊ីណុកដំបងលួសដែកអ៊ីណុក1000 គក
ដំបងលួសស្ពាន់ដំបងលួសស្ពាន់1000 គក
2

Point and string up

The end is pointed, pushed through each die and wound round each block in turn: this is called stringing-up.

ឧបករណ៍ដែលត្រូវការ៖

ម៉ាស៊ីនទាញលួសជាប់គ្នាម៉ាស៊ីនទាញលួសជាប់គ្នា
ពុម្ពទាញលួសតង់ស្តែនកាប៊ីតពុម្ពទាញលួសតង់ស្តែនកាប៊ីត
3

Draw

Lubricant floods the dies while each block pulls the wire through the next, smaller die; each block turns faster than the one before.

ឧបករណ៍ដែលត្រូវការ៖

ម៉ាស៊ីនទាញលួសជាប់គ្នាម៉ាស៊ីនទាញលួសជាប់គ្នា
ពុម្ពទាញលួសតង់ស្តែនកាប៊ីតពុម្ពទាញលួសតង់ស្តែនកាប៊ីត
ប្រេងរំអិលសម្រាប់ទាញលួសប្រេងរំអិលសម្រាប់ទាញលួស
4

Anneal when needed

Past about 50 % total reduction the wire is annealed before further drawing. A final anneal may follow to make the wire more ductile and, for copper, more conductive.

ឧបករណ៍ដែលត្រូវការ៖

ឡធ្វើឲ្យលោហៈទន់ឡធ្វើឲ្យលោហៈទន់
5

Gauge and coil

The finished diameter is measured and the wire is wound onto reels or coils.

ឧបករណ៍ដែលត្រូវការ៖

ជញ្ជីងវាស់ឌីជីថល ៦ អ៊ីញជញ្ជីងវាស់ឌីជីថល ៦ អ៊ីញ

សម្ភារៈ

3

ឧបករណ៍ចាំបាច់

5

ប្លង់ពាក់ព័ន្ធ

ប្លង់ទាំងនេះចែករំលែកចំណេះដឹង — បច្ចេកទេស សម្ភារៈ ឬគោលការណ៍

CC0 សាធារណៈ

ប្លង់នេះត្រូវបានចេញផ្សាយក្រោម CC0។ អ្នកមានសិទ្ធិចម្លង កែប្រែ ចែកចាយ និងប្រើប្រាស់ដោយមិនចាំបាច់សុំអនុញ្ញាត។

គាំទ្រអ្នកបង្កើតដោយទិញផលិតផលតាមរយៈប្លង់របស់ពួកគេ ដែលពួកគេទទួលបាន កម្រៃជើងសារអ្នកបង្កើត កំណត់ដោយអ្នកលក់ ឬបង្កើតកំណែថ្មីនៃប្លង់នេះ ហើយបញ្ចូលជាការតភ្ជាប់ក្នុងប្លង់របស់អ្នកដើម្បីចែករំលែកចំណូល។

ការពិភាក្សា

(0)

ចូល ដើម្បីចូលរួមពិភាក្សា

កំពុងផ្ទុកមតិ...