កិច្ចសហប្រតិបត្តិការ
សិល្បៈ
សម្រស់ និង សុខុមាលភាព
សិប្បកម្ម
វប្បធម៌ និង ប្រវត្តិសាស្ត្រ
ការកម្សាន្ត
បរិស្ថាន
ម្ហូប និង ភេសជ្ជៈ
វិស្វកម្មបញ្ច្រាស
វិទ្យាសាស្ត្រ
កីឡា
បច្ចេកវិទ្យា
ប្រដាប់ដែលស្លៀក
Steel-Faced Hand Hammers and Sledges: Ball, Fuller, Wedge and Claw Panes, Eye on Two Oval Drifts (Edwinson, 1886)
Forge

បង្កើតដោយ

Forge

14. វិច្ឆិកា 2026NO
10
0
0
0
0

Steel-Faced Hand Hammers and Sledges: Ball, Fuller, Wedge and Claw Panes, Eye on Two Oval Drifts (Edwinson, 1886)

How smiths made hand hammers and sledges, from George Edwinson's smithing series (Amateur Work, 1886): solid steel, or an iron head with a steel face welded into a slit fork; the eye punched and shaped on two oval taper drifts so the wedged handle cannot work loose. Panes: ball, fuller, wedge and claw.
កម្រិតខ្ពស់
A day at the forge

ការណែនាំ

1

His weights

កំពុងផ្ទុកសៀវភៅ Jupyter…
2

Read Edwinson

"To make a steel hammer it is only necessary to get a bar of steel the required size, heat, upset, and forge to the selected size and shape."
3

Solid steel route

Heat a steel bar of the size needed, upset it and forge it to shape. Punch the hole for the handle and work it on a taper drift. Tool the hammer off smoothly at a red heat, then heat it and harden it in water.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ដែកថែបរំលាយក្នុងឆ្នាំងដែកថែបរំលាយក្នុងឆ្នាំង1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

ឡជាងដែកឡជាងដែក
ទាំងជល់ (កំណាត់ដែក)ទាំងជល់ (កំណាត់ដែក)
ញញួរធំញញួរធំ
ដង្កៀបជាងដែកដង្កៀបជាងដែក
ដែកស្រួចពង្រីករន្ធដែកស្រួចពង្រីករន្ធ
ធុងជ្រលក់ត្រជាក់ធុងជ្រលក់ត្រជាក់
4

Steel-faced route: weld the face

Upset a stout iron bar if it is too thin. Slit one end hot with a hot chisel (his sett) into a fork. Forge a steel bar to a wedge that fits it. Bring the iron to a welding heat and the steel to its own (a separate fire if needed), roll the steel in calcined borax and weld. Reheat with the steel protected by welding mixture or sand, and finish the weld.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ដំបងដែកវាយដំបងដែកវាយ1 ដុំ
ដំបងដែកពពុះដំបងដែកពពុះ1 ដុំ
ម្សៅបូរ៉ាក់ម្សៅបូរ៉ាក់1 ដុំ
ខ្សាច់ខ្សាច់1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

ឡជាងដែកឡជាងដែក
ដែកកាត់ក្ដៅដែកកាត់ក្ដៅ
ទាំងជល់ (កំណាត់ដែក)ទាំងជល់ (កំណាត់ដែក)
ញញួរធំញញួរធំ
ដង្កៀបជាងដែកដង្កៀបជាងដែក
5

Shape the head

Cut off the steel, forge steel and iron up into the face. Fashion the head and pane, punch the handle hole and form it on a taper drift, cut the hammer off the bar and finish it held in crooked bit tongs. If both ends are to be steel, weld in both before cutting off. Panes: ball for riveting, fuller for spreading iron, wedge, or claw for drawing nails.

ឧបករណ៍ដែលត្រូវការ៖

ឡជាងដែកឡជាងដែក
ដែកស្រួចពង្រីករន្ធដែកស្រួចពង្រីករន្ធ
ដែកកាត់ក្ដៅដែកកាត់ក្ដៅ
ទាំងជល់ (កំណាត់ដែក)ទាំងជល់ (កំណាត់ដែក)
ញញួរញញួរ
ដង្កៀបជាងដែកដង្កៀបជាងដែក
6

Shape the eye on two drifts

Use two oval taper drifts: one tapered all round to form the lower side of the eye, the other tapered only on its long sides for the upper part. The eye tapers from both sides across the head, but only from the lower side lengthwise. Round the edges on the underside.

ឧបករណ៍ដែលត្រូវការ៖

ឡជាងដែកឡជាងដែក
ដែកស្រួចពង្រីករន្ធដែកស្រួចពង្រីករន្ធ
ទាំងជល់ (កំណាត់ដែក)ទាំងជល់ (កំណាត់ដែក)
ញញួរញញួរ
7

Sizes and sledges

Hand hammers usually weigh 1-2 lb (0.45-0.9 kg). Larger fuller or wedge pane hammers of 3-30 lb are sledges; one-handed sledges weigh 3-5 lb; heavier ones get stout ash handles 3-4 ft (0.9-1.2 m) long for two hands.

ឧបករណ៍ដែលត្រូវការ៖

ទាំងជល់ (កំណាត់ដែក)ទាំងជល់ (កំណាត់ដែក)
8

Hang the head

Drive the handle into the eye from below so its end is compressed and fits tight. Cut off the extra wood, split the end with a chisel and drive in a wedge of well-seasoned wood. If the eye tapers two ways, cross-slit and drive two wedges.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ដុំឈើអាសដុំឈើអាស1 ដុំ
ស្នូលឈើស្នូលឈើ1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

កាំបិតទាញពីរដងកាំបិតទាញពីរដង
ដែកឆូតឈើដែកឆូតឈើ
ញញួរញញួរ
9

Troubleshooting

Hammer troubleshooting.

Flow

Loading...
10

History and honest limits

From George Edwinson, "Smithing and Forging" (part X), **Amateur Work, Illustrated**, vol. VI (Ward, Lock & Co., 1886-87), pp. 211-214 (checked on the archive.org scan amateurworkillus06lond), pp. 212-214 and figs. 227-235. He gives no temper for the face; the metric figures and tools are ours.

សម្ភារៈ

7

ឧបករណ៍ចាំបាច់

10

CC0 សាធារណៈ

ប្លង់នេះត្រូវបានចេញផ្សាយក្រោម CC0។ អ្នកមានសិទ្ធិចម្លង កែប្រែ ចែកចាយ និងប្រើប្រាស់ដោយមិនចាំបាច់សុំអនុញ្ញាត។

គាំទ្រអ្នកបង្កើតដោយទិញផលិតផលតាមរយៈប្លង់របស់ពួកគេ ដែលពួកគេទទួលបាន កម្រៃជើងសារអ្នកបង្កើត កំណត់ដោយអ្នកលក់ ឬបង្កើតកំណែថ្មីនៃប្លង់នេះ ហើយបញ្ចូលជាការតភ្ជាប់ក្នុងប្លង់របស់អ្នកដើម្បីចែករំលែកចំណូល។

ការពិភាក្សា

(0)

ចូល ដើម្បីចូលរួមពិភាក្សា

កំពុងផ្ទុកមតិ...