កិច្ចសហប្រតិបត្តិការ
សិល្បៈ
សម្រស់ និង សុខុមាលភាព
សិប្បកម្ម
វប្បធម៌ និង ប្រវត្តិសាស្ត្រ
ការកម្សាន្ត
បរិស្ថាន
ម្ហូប និង ភេសជ្ជៈ
វិស្វកម្មបញ្ច្រាស
វិទ្យាសាស្ត្រ
កីឡា
បច្ចេកវិទ្យា
ប្រដាប់ដែលស្លៀក
Brass Binding-Screw: Body Turned from 5/8 in. Rod, Thumb Screws from 3/8 in. Rod, and a Bent Brass Clamp (Edwinson, 1881)
Volt

បង្កើតដោយ

Volt

14. វិច្ឆិកា 2026SE
9
0
0
0
0

Brass Binding-Screw: Body Turned from 5/8 in. Rod, Thumb Screws from 3/8 in. Rod, and a Bent Brass Clamp (Edwinson, 1881)

The Victorian battery terminal, from George Edwinson's Electro-plating at Home (Amateur Work, 1881): a brass body turned from 1 1/2 in. of 5/8 in. rod, slotted for the plate and bored for the wire, with thumb screws turned from 3/8 in. rod; or a clamp bent hot from a brass strip with a soldered-on wire piece.
មធ្យម
Two hours at the lathe

ការណែនាំ

1

His sizes

កំពុងផ្ទុកសៀវភៅ Jupyter…
2

Read Edwinson

"Those who may have lathes ... may easily turn up a binding-screw ... out of a 1 1/2 in. length of 5/8 in. brass rod."
3

Turn the body

Cut 1 1/2 in. (38 mm) of 5/8 in. (16 mm) brass rod and turn the body to shape first (his fig. 3: a round head on a tapering neck over a forked foot).

សម្ភារៈសម្រាប់ជំហាននេះ៖

ដុំស្ពាន់លឿងដុំស្ពាន់លឿង1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

រណារកាត់ដែករណារកាត់ដែក
ម៉ាស៊ីនកាត់ដែក (ទ័រ)ម៉ាស៊ីនកាត់ដែក (ទ័រ)
ដែកកាត់ដាច់ (ម៉ាស៊ីនកិន)ដែកកាត់ដាច់ (ម៉ាស៊ីនកិន)
4

Slot and bore

Cut the slot that grips the plate. Bore a hole for the wire through the head, then bore the holes for the screws.

ឧបករណ៍ដែលត្រូវការ៖

ដង្កាប់តុដង្កាប់តុ
រណារកាត់ដែករណារកាត់ដែក
ដែកឆាប (ដែកឆាបដៃ)ដែកឆាប (ដែកឆាបដៃ)
ស្វានដៃស្វានដៃ
5

Turn the thumb screws

Turn the screws from 3/8 in. (9.5 mm) brass rod with plain thumb-screw heads (he says milled heads are a mistake). Cut a fine thread on them and tap the holes to match.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ដុំស្ពាន់លឿងដុំស្ពាន់លឿង1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

ម៉ាស៊ីនកាត់ដែក (ទ័រ)ម៉ាស៊ីនកាត់ដែក (ទ័រ)
ដែកកាត់ដាច់ (ម៉ាស៊ីនកិន)ដែកកាត់ដាច់ (ម៉ាស៊ីនកិន)
ឈុតកាត់ខ្សែវីសឈុតកាត់ខ្សែវីស
6

Bent clamp (variant)

From good malleable brass take a strip 3 in. long, 1/2 in. wide and 1/4 in. thick (76 x 13 x 6 mm). Heat it to a dull red and bend it over a former of hot iron. Cut the piece for the wire and centre screw separately, hard-solder it on and trim it. Fit thumb screws as above. (A clamp may also be cast from a wooden pattern.)

សម្ភារៈសម្រាប់ជំហាននេះ៖

បន្ទះលង្ហិនបន្ទះលង្ហិន1 ដុំ
សំណផ្សារប្រាក់សំណផ្សារប្រាក់1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

ឡជាងដែកឡជាងដែក
ដង្កៀបជាងដែកដង្កៀបជាងដែក
ញញួរញញួរ
ដុំភ្លើងផ្សារស្ពាន់ដុំភ្លើងផ្សារស្ពាន់
ដែកឆាប (ដែកឆាបដៃ)ដែកឆាប (ដែកឆាបដៃ)
ស្វានដៃស្វានដៃ
ឈុតកាត់ខ្សែវីសឈុតកាត់ខ្សែវីស
7

Clean and keep it working

Clean the slot with folded emery cloth and the wire hole with the tang of a file. Now and then oil the screw, work it in and out, and wipe the oil off. Do not screw up too tight.

ឧបករណ៍ដែលត្រូវការ៖

ដែកឆាប (ដែកឆាបដៃ)ដែកឆាប (ដែកឆាបដៃ)
8

Troubleshooting

Binding-screw troubleshooting.

Flow

Loading...
9

History and honest limits

From George Edwinson, "Electro-plating at Home", **Amateur Work, Illustrated**, vol. I (1881), p. 81 figs. 3 and 7 and p. 99 (checked on the archive.org scan amateurworkillus11881lond). He gives no thread size. Modern panel binding posts add an insulating bush and a banana-plug socket; this is the 1881 brass terminal. The metric figures and the tools are ours.

សម្ភារៈ

3

ឧបករណ៍ចាំបាច់

11

ប្លង់ពាក់ព័ន្ធ

ប្លង់ទាំងនេះចែករំលែកចំណេះដឹង — បច្ចេកទេស សម្ភារៈ ឬគោលការណ៍

CC0 សាធារណៈ

ប្លង់នេះត្រូវបានចេញផ្សាយក្រោម CC0។ អ្នកមានសិទ្ធិចម្លង កែប្រែ ចែកចាយ និងប្រើប្រាស់ដោយមិនចាំបាច់សុំអនុញ្ញាត។

គាំទ្រអ្នកបង្កើតដោយទិញផលិតផលតាមរយៈប្លង់របស់ពួកគេ ដែលពួកគេទទួលបាន កម្រៃជើងសារអ្នកបង្កើត កំណត់ដោយអ្នកលក់ ឬបង្កើតកំណែថ្មីនៃប្លង់នេះ ហើយបញ្ចូលជាការតភ្ជាប់ក្នុងប្លង់របស់អ្នកដើម្បីចែករំលែកចំណូល។

ការពិភាក្សា

(0)

ចូល ដើម្បីចូលរួមពិភាក្សា

កំពុងផ្ទុកមតិ...