កិច្ចសហប្រតិបត្តិការ
សិល្បៈ
សម្រស់ និង សុខុមាលភាព
សិប្បកម្ម
វប្បធម៌ និង ប្រវត្តិសាស្ត្រ
ការកម្សាន្ត
បរិស្ថាន
ម្ហូប និង ភេសជ្ជៈ
វិស្វកម្មបញ្ច្រាស
វិទ្យាសាស្ត្រ
កីឡា
បច្ចេកវិទ្យា
ប្រដាប់ដែលស្លៀក
ESP32 Self-Watering Pot Controller
Ed

បង្កើតដោយ

Ed

16. វិច្ឆិកា 2026FI
2
0
0
0
0

ESP32 Self-Watering Pot Controller

A tank unit that sits next to one houseplant pot. An ESP32 reads a capacitive soil-moisture sensor in the pot and an ultrasonic sensor looking down into a 1.7 L printed water tank. It shows soil moisture % and tank level % on a 0.96 in OLED and runs a small 5 V submersible pump through a logic-level MOSFET when the soil is dry and the tank is not empty. Powered from USB-C 5 V.

ការណែនាំ

1

Circuit board

កំពុងផ្ទុកកម្មវិធីមើល KiCanvas...

កម្មវិធីមើលការរចនា PCB ជំនាញ

2

Schematic

កំពុងផ្ទុកកម្មវិធីមើល KiCanvas...

កម្មវិធីមើលការរចនា PCB ជំនាញ

3

Print the enclosure base

ឯកសាររចនាSTL71.6 KBCC0 - Free
4

Print the enclosure lid

ឯកសាររចនាSTL79.1 KBCC0 - Free
5

Print the button plunger

ឯកសាររចនាSTL16.3 KBCC0 - Free
6

Print the water tank

ឯកសាររចនាSTL1.4 KBCC0 - Free
7

Print the tank lid with enclosure seat

ឯកសាររចនាSTL46.5 KBCC0 - Free
8

Print the tube stake for the pot

ឯកសាររចនាSTL32.2 KBCC0 - Free
9

Firmware

firmware.inoarduino
// Self-watering pot controller - ESP32 DevKit (38-pin) carrier board
// Soil: capacitive v1.2 on GPIO34 (ADC1). Tank: HC-SR04 TRIG=GPIO5, ECHO=GPIO18 (via 1k/2k divider).
// OLED SSD1306 128x64 I2C @0x3C on SDA=21 SCL=22. Pump MOSFET gate GPIO25. Button GPIO27 to GND.
// Button: short press = force a watering cycle, hold 3 s = calibrate soil sensor (dry / wet).
#include <Arduino.h>
#include <Wire.h>
#include <Preferences.h>

// ---------------- pins ----------------
const int PIN_SOIL = 34;
const int PIN_TRIG = 5;
const int PIN_ECHO = 18;
const int PIN_PUMP = 25;
const int PIN_BTN  = 27;
const int PIN_SDA  = 21;
const int PIN_SCL  = 22;

// ---------------- settings (adjust for your pot / tank) ----------------
const float TANK_EMPTY_CM   = 20.0;  // sensor-to-water distance when tank is empty
const float TANK_FULL_CM    = 4.0;   // sensor-to-water distance when tank is full
const int   SOIL_DRY_PCT    = 35;    // start watering below this moisture %
const int   TANK_MIN_PCT    = 10;    // never pump below this tank level %
const uint32_t PUMP_RUN_MS  = 5000;  // one watering shot
const uint32_t SOAK_MS      = 10UL * 60UL * 1000UL; // wait for water to soak in before next automatic shot
const uint32_t MEASURE_MS   = 1000;

Preferences prefs;
int calDry = 3000;   // raw ADC in air (dry)
int calWet = 1300;   // raw ADC in water (wet)

// ---------------- minimal SSD1306 driver ----------------
const uint8_t OLED_ADDR = 0x3C;
uint8_t fb[1024];
bool oledOk = false;

static const uint8_t FONT[] PROGMEM = {
0x00,0x00,0x00,0x00,0x00, 0x00,0x00,0x5F,0x00,0x00, 0x00,0x07,0x00,0x07,0x00, 0x14,0x7F,0x14,0x7F,0x14,
0x24,0x2A,0x7F,0x2A,0x12, 0x23,0x13,0x08,0x64,0x62, 0x36,0x49,0x56,0x20,0x50, 0x00,0x08,0x07,0x03,0x00,
0x00,0x1C,0x22,0x41,0x00, 0x00,0x41,0x22,0x1C,0x00, 0x2A,0x1C,0x7F,0x1C,0x2A, 0x08,0x08,0x3E,0x08,0x08,
0x00,0x80,0x70,0x30,0x00, 0x08,0x08,0x08,0x08,0x08, 0x00,0x00,0x60,0x60,0x00, 0x20,0x10,0x08,0x04,0x02,
0x3E,0x51,0x49,0x45,0x3E, 0x00,0x42,0x7F,0x40,0x00, 0x72,0x49,0x49,0x49,0x46, 0x21,0x41,0x49,0x4D,0x33,
0x18,0x14,0x12,0x7F,0x10, 0x27,0x45,0x45,0x45,0x39, 0x3C,0x4A,0x49,0x49,0x31, 0x41,0x21,0x11,0x09,0x07,
0x36,0x49,0x49,0x49,0x36, 0x46,0x49,0x49,0x29,0x1E, 0x00,0x00,0x14,0x00,0x00, 0x00,0x40,0x34,0x00,0x00,
0x00,0x08,0x14,0x22,0x41, 0x14,0x14,0x14,0x14,0x14, 0x00,0x41,0x22,0x14,0x08, 0x02,0x01,0x59,0x09,0x06,
0x3E,0x41,0x5D,0x59,0x4E, 0x7C,0x12,0x11,0x12,0x7C, 0x7F,0x49,0x49,0x49,0x36, 0x3E,0x41,0x41,0x41,0x22,
0x7F,0x41,0x41,0x41,0x3E, 0x7F,0x49,0x49,0x49,0x41, 0x7F,0x09,0x09,0x09,0x01, 0x3E,0x41,0x41,0x51,0x73,
0x7F,0x08,0x08,0x08,0x7F, 0x00,0x41,0x7F,0x41,0x00, 0x20,0x40,0x41,0x3F,0x01, 0x7F,0x08,0x14,0x22,0x41,
0x7F,0x40,0x40,0x40,0x40, 0x7F,0x02,0x1C,0x02,0x7F, 0x7F,0x04,0x08,0x10,0x7F, 0x3E,0x41,0x41,0x41,0x3E,
0x7F,0x09,0x09,0x09,0x06, 0x3E,0x41,0x51,0x21,0x5E, 0x7F,0x09,0x19,0x29,0x46, 0x26,0x49,0x49,0x49,0x32,
0x03,0x01,0x7F,0x01,0x03, 0x3F,0x40,0x40,0x40,0x3F, 0x1F,0x20,0x40,0x20,0x1F, 0x3F,0x40,0x38,0x40,0x3F,
0x63,0x14,0x08,0x14,0x63, 0x03,0x04,0x78,0x04,0x03, 0x61,0x59,0x49,0x4D,0x43, 0x00,0x7F,0x41,0x41,0x41,
0x02,0x04,0x08,0x10,0x20, 0x00,0x41,0x41,0x41,0x7F, 0x04,0x02,0x01,0x02,0x04, 0x40,0x40,0x40,0x40,0x40,
0x00,0x03,0x07,0x08,0x00, 0x20,0x54,0x54,0x78,0x40, 0x7F,0x28,0x44,0x44,0x38, 0x38,0x44,0x44,0x44,0x28,
0x38,0x44,0x44,0x28,0x7F, 0x38,0x54,0x54,0x54,0x18, 0x00,0x08,0x7E,0x09,0x02, 0x18,0xA4,0xA4,0x9C,0x78,
0x7F,0x08,0x04,0x04,0x78, 0x00,0x44,0x7D,0x40,0x00, 0x20,0x40,0x40,0x3D,0x00, 0x7F,0x10,0x28,0x44,0x00,
0x00,0x41,0x7F,0x40,0x00, 0x7C,0x04,0x78,0x04,0x78, 0x7C,0x08,0x04,0x04,0x78, 0x38,0x44,0x44,0x44,0x38,
0xFC,0x18,0x24,0x24,0x18, 0x18,0x24,0x24,0x18,0xFC, 0x7C,0x08,0x04,0x04,0x08, 0x48,0x54,0x54,0x54,0x24,
0x04,0x04,0x3F,0x44,0x24, 0x3C,0x40,0x40,0x20,0x7C, 0x1C,0x20,0x40,0x20,0x1C, 0x3C,0x40,0x30,0x40,0x3C,
0x44,0x28,0x10,0x28,0x44, 0x4C,0x90,0x90,0x90,0x7C, 0x44,0x64,0x54,0x4C,0x44, 0x00,0x08,0x36,0x41,0x00,
0x00,0x00,0x77,0x00,0x00, 0x00,0x41,0x36,0x08,0x00, 0x02,0x01,0x02,0x04,0x02
};

void oledCmd(uint8_t c) {
  Wire.beginTransmission(OLED_ADDR); Wire.write(0x00); Wire.write(c); Wire.endTransmission();
}

bool oledInit() {
  Wire.beginTransmission(OLED_ADDR);
  if (Wire.endTransmission() != 0) return false;
  const uint8_t init[] = {0xAE,0xD5,0x80,0xA8,0x3F,0xD3,0x00,0x40,0x8D,0x14,0x20,0x00,
                          0xA1,0xC8,0xDA,0x12,0x81,0xCF,0xD9,0xF1,0xDB,0x40,0xA4,0xA6,0x2E,0xAF};
  for (uint8_t c : init) oledCmd(c);
  return true;
}

void oledShow() {
  if (!oledOk) return;
  oledCmd(0x21); oledCmd(0); oledCmd(127);
  oledCmd(0x22); oledCmd(0); oledCmd(7);
  for (int i = 0; i < 1024; i += 16) {
    Wire.beginTransmission(OLED_ADDR);
    Wire.write(0x40);
    Wire.write(&fb[i], 16);
    Wire.endTransmission();
  }
}

void clearFb() { memset(fb, 0, sizeof(fb)); }

void setPixel(int x, int y) {
  if (x < 0 || x > 127 || y < 0 || y > 63) return;
  fb[x + (y / 8) * 128] |= (1 << (y & 7));
}

void drawChar(int x, int y, char c, int s) {
  if (c < 32 || c > 126) c = '?';
  for (int col = 0; col < 5; col++) {
    uint8_t bits = pgm_read_byte(&FONT[(c - 32) * 5 + col]);
    for (int row = 0; row < 8; row++)
      if (bits & (1 << row))
        for (int dx = 0; dx < s; dx++)
          for (int dy = 0; dy < s; dy++) setPixel(x + col * s + dx, y + row * s + dy);
  }
}

void drawText(int x, int y, const char *t, int s = 1) {
  while (*t) { drawChar(x, y, *t++, s); x += 6 * s; }
}

void drawBar(int x, int y, int w, int h, int pct) {
  for (int i = 0; i < w; i++) { setPixel(x + i, y); setPixel(x + i, y + h - 1); }
  for (int j = 0; j < h; j++) { setPixel(x, y + j); setPixel(x + w - 1, y + j); }
  int fill = (w - 4) * constrain(pct, 0, 100) / 100;
  for (int i = 0; i < fill; i++)
    for (int j = 2; j < h - 2; j++) setPixel(x + 2 + i, y + j);
}

// ---------------- sensors ----------------
int readSoilRaw() {
  long sum = 0;
  for (int i = 0; i < 16; i++) { sum += analogRead(PIN_SOIL); delay(2); }
  return sum / 16;
}

int soilPercent(int raw) {
  if (calDry == calWet) return 0;
  long p = (long)(calDry - raw) * 100 / (calDry - calWet);
  return constrain((int)p, 0, 100);
}

float readDistanceCm() {
  float best[5]; int n = 0;
  for (int i = 0; i < 5; i++) {
    digitalWrite(PIN_TRIG, LOW); delayMicroseconds(4);
    digitalWrite(PIN_TRIG, HIGH); delayMicroseconds(10);
    digitalWrite(PIN_TRIG, LOW);
    unsigned long us = pulseIn(PIN_ECHO, HIGH, 30000UL);
    if (us > 0) best[n++] = us / 58.0f;
    delay(30);
  }
  if (n == 0) return -1;
  for (int i = 0; i < n; i++)            // median
    for (int j = i + 1; j < n; j++)
      if (best[j] < best[i]) { float t = best[i]; best[i] = best[j]; best[j] = t; }
  return best[n / 2];
}

int tankPercent(float cm) {
  if (cm < 0) return -1;
  float p = (TANK_EMPTY_CM - cm) * 100.0f / (TANK_EMPTY_CM - TANK_FULL_CM);
  return constrain((int)p, 0, 100);
}

// ---------------- pump ----------------
bool pumpOn = false;
uint32_t pumpStart = 0, lastWater = 0;
bool everWatered = false;

void pump(bool on) {
  pumpOn = on;
  digitalWrite(PIN_PUMP, on ? HIGH : LOW);
  if (on) pumpStart = millis();
  else { lastWater = millis(); everWatered = true; }
}

// ---------------- button ----------------
// returns 0 = nothing, 1 = short press, 2 = long press (>3 s)
int readButton() {
  static bool was = false; static uint32_t t0 = 0; static bool longDone = false;
  bool down = digitalRead(PIN_BTN) == LOW;
  int ev = 0;
  if (down && !was) { t0 = millis(); longDone = false; }
  if (down && !longDone && millis() - t0 > 3000) { ev = 2; longDone = true; }
  if (!down && was && !longDone && millis() - t0 > 40) ev = 1;
  was = down;
  return ev;
}

void waitPress() {
  while (digitalRead(PIN_BTN) == LOW) delay(10);
  delay(50);
  while (digitalRead(PIN_BTN) == HIGH) delay(10);
  delay(50);
  while (digitalRead(PIN_BTN) == LOW) delay(10);
}

void calibrate() {
  pump(false);
  clearFb(); drawText(0, 0, "CALIBRATE SOIL", 1);
  drawText(0, 16, "1) Sensor in DRY air"); drawText(0, 28, "   then press button");
  oledShow(); waitPress();
  int dry = readSoilRaw();
  clearFb(); drawText(0, 0, "CALIBRATE SOIL", 1);
  drawText(0, 16, "2) Sensor in WATER"); drawText(0, 28, "   (up to the line)"); drawText(0, 40, "   then press button");
  oledShow(); waitPress();
  int wet = readSoilRaw();
  clearFb();
  if (dry - wet > 200) {
    calDry = dry; calWet = wet;
    prefs.putInt("dry", calDry); prefs.putInt("wet", calWet);
    drawText(0, 16, "Saved."); 
  } else {
    drawText(0, 16, "Bad readings,"); drawText(0, 28, "not saved.");
  }
  char b[32]; snprintf(b, sizeof(b), "dry=%d wet=%d", dry, wet); drawText(0, 44, b);
  oledShow(); delay(2500);
}

void setup() {
  pinMode(PIN_PUMP, OUTPUT); digitalWrite(PIN_PUMP, LOW);
  pinMode(PIN_TRIG, OUTPUT); digitalWrite(PIN_TRIG, LOW);
  pinMode(PIN_ECHO, INPUT);
  pinMode(PIN_BTN, INPUT_PULLUP);
  Serial.begin(115200);
  analogReadResolution(12);
  analogSetPinAttenuation(PIN_SOIL, ADC_11db);
  prefs.begin("plantpot", false);
  calDry = prefs.getInt("dry", calDry);
  calWet = prefs.getInt("wet", calWet);
  Wire.begin(PIN_SDA, PIN_SCL, 400000);
  oledOk = oledInit();
  clearFb(); drawText(10, 24, "PlantPot", 2); oledShow();
  delay(1000);
}

void loop() {
  static uint32_t lastMeas = 0;
  static int soil = 0, tank = -1, raw = 0;
  static float dist = -1;
  static bool forceRequest = false;

  int ev = readButton();
  if (ev == 2) { calibrate(); lastMeas = 0; }
  if (ev == 1) forceRequest = true;

  // pump safety timeout
  if (pumpOn && millis() - pumpStart >= PUMP_RUN_MS) pump(false);

  if (millis() - lastMeas >= MEASURE_MS || lastMeas == 0) {
    lastMeas = millis();
    raw = readSoilRaw();
    soil = soilPercent(raw);
    dist = readDistanceCm();
    tank = tankPercent(dist);
    bool tankOk = tank >= TANK_MIN_PCT;          // unknown (-1) counts as empty
    if (pumpOn && !tankOk) pump(false);

    if (!pumpOn && tankOk) {
      bool soaked = !everWatered || millis() - lastWater >= SOAK_MS;
      if (forceRequest || (soil < SOIL_DRY_PCT && soaked)) pump(true);
    }
    forceRequest = false;

    Serial.printf("soil raw=%d %d%%  dist=%.1fcm tank=%d%%  pump=%d\n", raw, soil, dist, tank, pumpOn);

    clearFb();
    char b[24];
    drawText(0, 0, "SOIL");
    snprintf(b, sizeof(b), "%3d%%", soil); drawText(70, 0, b, 2);
    drawBar(0, 18, 128, 8, soil);
    drawText(0, 32, "TANK");
    if (tank < 0) snprintf(b, sizeof(b), " ?? "); else snprintf(b, sizeof(b), "%3d%%", tank);
    drawText(70, 32, b, 2);
    drawBar(0, 48, 128, 8, tank < 0 ? 0 : tank);
    if (pumpOn) drawText(30, 0, "PUMP");
    else if (!tankOk) drawText(30, 0, "FILL!");
    oledShow();
  }
  delay(10);
}
10

Check board and parts

Check the bare PCB for shorts between +5V and GND with a multimeter. Measure the ESP32 dev board row spacing: the sockets are 25.4 mm apart.

សម្ភារៈសម្រាប់ជំហាននេះ៖

បន្ទះសៀគ្វីបោះពុម្ពបន្ទះសៀគ្វីបោះពុម្ព1 pcs

ឧបករណ៍ដែលត្រូវការ៖

ម៉ាល់ទីម៉ែត្រម៉ាល់ទីម៉ែត្រ
11

Solder SMD parts

Solder R1 and R2 (5.1k, CC pull-downs), R3 (100R gate), R4 (100k gate pull-down), R5 (1k), R6 (2k) and C2 (100 nF), all 0805. Then solder the USB-C receptacle J3.

សម្ភារៈសម្រាប់ជំហាននេះ៖

រេស៊ីស្ទ័របន្ទះឈីបរេស៊ីស្ទ័របន្ទះឈីប6 pcs
កុងដង់ស័រសេរ៉ាមិចបន្ទះឈីបកុងដង់ស័រសេរ៉ាមិចបន្ទះឈីប1 pcs
USB-C ReceptacleUSB-C Receptacle1 pcs
ខ្សែសំណផ្សារខ្សែសំណផ្សារ5 ក្រ

ឧបករណ៍ដែលត្រូវការ៖

ដែកផ្សារដែកផ្សារ
12

Solder through-hole parts

Solder D1 (1N5819, band to +5V), Q1 (IRLZ44N), C1 (470 uF 10 V, mind polarity), J4 pump terminal, J5 and J6 JST-XH headers, J7 OLED header, SW1 and the two 1x19 female sockets.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ឌីអូតឌីអូត1 pcs
MOSFET កម្រិតឡូស៊ិក IRLZ44NMOSFET កម្រិតឡូស៊ិក IRLZ44N1 pcs
កុងដង់ស័រអេឡិចត្រូលីតកុងដង់ស័រអេឡិចត្រូលីត1 pcs
ប្លុកចំណុចភ្ជាប់វីសប្លុកចំណុចភ្ជាប់វីស1 pcs
JST-XH Board HeaderJST-XH Board Header2 pcs
ជួរម្ជុលភ្ជាប់ជួរម្ជុលភ្ជាប់3 pcs
ប៊ូតុងចុចប៊ូតុងចុច1 pcs
ខ្សែសំណផ្សារខ្សែសំណផ្សារ10 ក្រ

ឧបករណ៍ដែលត្រូវការ៖

ដែកផ្សារដែកផ្សារ
13

Check rails and fit ESP32

Power the board through USB-C from a bench supply set to 5 V, 0.3 A limit, without the ESP32. Check 5 V on the DevKit 5V socket pin and on J4 pin 1. Then plug in the ESP32 dev board with the antenna toward the SOIL edge.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ក្តារអភិវឌ្ឍន៍ ESP32ក្តារអភិវឌ្ឍន៍ ESP321 pcs

ឧបករណ៍ដែលត្រូវការ៖

ប្រភពថាមពលចរន្តផ្ទាល់ប្រភពថាមពលចរន្តផ្ទាល់
ម៉ាល់ទីម៉ែត្រម៉ាល់ទីម៉ែត្រ
14

Fit board into enclosure base

Set the controller board on the base standoffs with USB-C and the pump terminal at their openings. Fix with four M3 x 6 self-tapping screws.

សម្ភារៈសម្រាប់ជំហាននេះ៖

វីសកាត់ក្បាច់ខ្លួនឯងវីសកាត់ក្បាច់ខ្លួនឯង4 pcs

ឧបករណ៍ដែលត្រូវការ៖

ឈុតទួណឺវីសឈុតទួណឺវីស
15

Mount OLED in enclosure lid

Screw the OLED to the four lid posts with four M2 x 5 self-tapping screws (check the 23 x 23.5 mm hole pattern). Connect it to J7 with a 4-wire female jumper: GND, VCC, SCL, SDA. Put the plunger in the button hole.

សម្ភារៈសម្រាប់ជំហាននេះ៖

អេក្រង់ OLEDអេក្រង់ OLED1 pcs
វីសកាត់ក្បាច់ខ្លួនឯងវីសកាត់ក្បាច់ខ្លួនឯង4 pcs
ខ្សែភ្ជាប់ខ្សែភ្ជាប់4 pcs

ឧបករណ៍ដែលត្រូវការ៖

ឈុតទួណឺវីសឈុតទួណឺវីស
16

Mount pump and tank sensor

Set the pump on the tank floor. Pass its leads through the 6 mm lid hole and the tube through the 9.5 mm hole. Press the HC-SR04 transducers into the two 17 mm lid holes, facing down, and fix the sensor with hot glue.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ស្នប់លិចទឹកស្នប់លិចទឹក1 pcs
បំពង់ស៊ីលីកូនបំពង់ស៊ីលីកូន1 m
ឧបករណ៍ចាប់ចម្ងាយអ៊ុលត្រាសូនិកឧបករណ៍ចាប់ចម្ងាយអ៊ុលត្រាសូនិក1 pcs
ដំបងកាវរលាយដោយកម្ដៅដំបងកាវរលាយដោយកម្ដៅ1 pcs

ឧបករណ៍ដែលត្រូវការ៖

កាំភ្លើងកាវក្តៅកាំភ្លើងកាវក្តៅ
17

Wire pump and sensors

Extend the pump leads with hookup wire if needed, solder and cover with heat shrink. Pump + to J4 pin 1, pump - to J4 pin 2. Solder a 4-pin JST-XH cable to the HC-SR04 (VCC, TRIG, ECHO, GND) and a 3-pin cable to the soil sensor (GND, VCC, AOUT). Plug into J6 and J5.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ខ្សែភ្លើងភ្ជាប់ខ្សែភ្លើងភ្ជាប់1 m
បំពង់រួញដោយកម្តៅបំពង់រួញដោយកម្តៅ10 សម
Capacitive Soil Moisture SensorCapacitive Soil Moisture Sensor1 pcs
JST-XH CableJST-XH Cable2 pcs
ខ្សែសំណផ្សារខ្សែសំណផ្សារ3 ក្រ

ឧបករណ៍ដែលត្រូវការ៖

ដែកផ្សារដែកផ្សារ
ដង្កាប់បកស្រទាប់លួសដង្កាប់បកស្រទាប់លួស
ឈុតទួណឺវីសឈុតទួណឺវីស
18

Flash firmware

With USB-C power unplugged, connect the DevKit micro-USB through the base slot to a computer. Set TANK_EMPTY_CM and TANK_FULL_CM for this tank, then upload firmware.ino for board esp32:esp32:esp32 with the Arduino IDE. Snap the enclosure lid on.

ឧបករណ៍ដែលត្រូវការ៖

កុំព្យូទ័រមាន Arduino IDEកុំព្យូទ័រមាន Arduino IDE
USB Data CableUSB Data Cable
19

Leak-test the tank

Fill the printed tank with water and leave it on paper towel for 24 h. If it seeps, reprint with more walls or seal the inside before use.

ឧបករណ៍ដែលត្រូវការ៖

ក្អមវាស់ក្អមវាស់
កន្សែងក្រដាសកន្សែងក្រដាស
ទឹកទឹក
20

Set up, calibrate and test

Seat the lid on the tank and the enclosure in the lid frame. Push the soil sensor into the pot up to its line and clip the tube end into the stake. Power from the USB-C adapter. Hold the button 3 s for dry/wet calibration. Press briefly to water and check flow, readings and pump current (under 0.8 A).

សម្ភារៈសម្រាប់ជំហាននេះ៖

USB-C Power AdapterUSB-C Power Adapter1 pcs
USB-C CableUSB-C Cable1 pcs

ឧបករណ៍ដែលត្រូវការ៖

ម៉ាល់ទីម៉ែត្រម៉ាល់ទីម៉ែត្រ
ក្អមវាស់ក្អមវាស់
ផើងផ្កាផើងផ្កា
ទឹកទឹក

សម្ភារៈ

26

ឧបករណ៍ចាំបាច់

12

ឯកសាររចនា

6

ប្លង់ពាក់ព័ន្ធ

ប្លង់ទាំងនេះចែករំលែកចំណេះដឹង — បច្ចេកទេស សម្ភារៈ ឬគោលការណ៍

CC0 សាធារណៈ

ប្លង់នេះត្រូវបានចេញផ្សាយក្រោម CC0។ អ្នកមានសិទ្ធិចម្លង កែប្រែ ចែកចាយ និងប្រើប្រាស់ដោយមិនចាំបាច់សុំអនុញ្ញាត។

គាំទ្រអ្នកបង្កើតដោយទិញផលិតផលតាមរយៈប្លង់របស់ពួកគេ ដែលពួកគេទទួលបាន កម្រៃជើងសារអ្នកបង្កើត កំណត់ដោយអ្នកលក់ ឬបង្កើតកំណែថ្មីនៃប្លង់នេះ ហើយបញ្ចូលជាការតភ្ជាប់ក្នុងប្លង់របស់អ្នកដើម្បីចែករំលែកចំណូល។

ការពិភាក្សា

(0)

ចូល ដើម្បីចូលរួមពិភាក្សា

កំពុងផ្ទុកមតិ...