កិច្ចសហប្រតិបត្តិការ
សិល្បៈ
សម្រស់ និង សុខុមាលភាព
សិប្បកម្ម
វប្បធម៌ និង ប្រវត្តិសាស្ត្រ
ការកម្សាន្ត
បរិស្ថាន
ម្ហូប និង ភេសជ្ជៈ
វិស្វកម្មបញ្ច្រាស
វិទ្យាសាស្ត្រ
កីឡា
បច្ចេកវិទ្យា
ប្រដាប់ដែលស្លៀក
Gas Burner: a Home-Made Bunsen Burner from Brass Tube (Work, 1892)
Charlie

បង្កើតដោយ

Charlie

7. វិច្ឆិកា 2026DE
11
0
0
0
0

Gas Burner: a Home-Made Bunsen Burner from Brass Tube (Work, 1892)

A Bunsen burner: gas from a fine jet draws air in through two holes at the foot of an upright tube, and the mixture burns at the top with a hot blue flame that leaves no soot. H. B. Stocks (Work, 1892) makes one from a 3 1/2 in. brass tube 1/2 in. across, a short 3/8 in. tube for the gas, a brass boss and elbow from a gas bracket, and a bit of fine-bore tube from an old oil-can as the jet. A sliding brass collar over the air-holes sets the flame. Source: H. B. Stocks, How to Make a Cheap Spirit Lamp, Bunsen Burner, Blowpipes, etc., Work No. 167 (28 May 1892), p. 167. Picture: his Figs. 3-4.
មធ្យម
Unknown

ការណែនាំ

1

Read Stocks

"To make a Bunsen burner the following materials will be necessary:—A piece of brass tube 3 1/2 in. long, 1/2 in. diameter (external); a piece of tube 3/8 in. in diameter, 1 1/2 in. long; a brass boss similar to those on an ordinary bracket, but without a tap; a brass elbow tube; also a piece of tubing with very fine bore (small bit of tube from an old oil-can will do)."
2

Solder the elbow on the boss

Solder the brass elbow-piece onto the brass boss, with the tube that has a screw cut for a gallery uppermost.

សម្ភារៈសម្រាប់ជំហាននេះ៖

គ្រឿងតភ្ជាប់បំពង់មានខ្សែវីសគ្រឿងតភ្ជាប់បំពង់មានខ្សែវីស2 boss and elbow
ផ្សារសំណប៉ាហាំង-សំណផ្សារសំណប៉ាហាំង-សំណ1 joint
ហ្វ្លុចហ្វ្លុច1 joint

ឧបករណ៍ដែលត្រូវការ៖

ដែកផ្សារដែកផ្សារ
3

Fit the jet

Cut the fine-bore tube 3/4 in. to 1 in. long and solder it inside the vertical tube of the elbow-piece so it projects about 1/2 in. If it is too small for the hole, plug round it with a little sheet lead, keeping it perfectly vertical and in the centre of the outer tube, then solder. The metal of the oil-can tube is not given (unknown).

សម្ភារៈសម្រាប់ជំហាននេះ៖

លោហៈមិនស្គាល់លោហៈមិនស្គាល់1 fine-bore tube
សន្លឹកសំណសន្លឹកសំណ1 packing
ផ្សារសំណប៉ាហាំង-សំណផ្សារសំណប៉ាហាំង-សំណ1 joint

ឧបករណ៍ដែលត្រូវការ៖

ដែកផ្សារដែកផ្សារ
កន្ត្រៃកាត់សន្លឹកលោហៈកន្ត្រៃកាត់សន្លឹកលោហៈ
4

Make the burner tube

Take the brass tube 3 1/2 in. long, 1/2 in. across. If it is not of very thick brass it will be a little too large: turn a piece of very thin sheet brass 1/2 in. by 1 1/4 in. into a cylinder and solder it inside one end. Tap that end inside to screw onto the male thread of the elbow-piece. At the same end drill two holes about 3/8 in. across, exactly opposite each other, their centres 5/8 in. from the end: the air-holes.

សម្ភារៈសម្រាប់ជំហាននេះ៖

បំពង់ស្ពាន់ អង្កត់ផ្ចិតក្រៅ ១/២ អ៊ីញបំពង់ស្ពាន់ អង្កត់ផ្ចិតក្រៅ ១/២ អ៊ីញ1 3 1/2 in.
សន្លឹកស្ពាន់លឿងសន្លឹកស្ពាន់លឿង1 1/2 x 1 1/4 in.
ផ្សារសំណប៉ាហាំង-សំណផ្សារសំណប៉ាហាំង-សំណ1 joint

ឧបករណ៍ដែលត្រូវការ៖

កន្ត្រៃកាត់សន្លឹកលោហៈកន្ត្រៃកាត់សន្លឹកលោហៈ
ដែកផ្សារដែកផ្សារ
ឈុតកាត់ខ្សែវីសឈុតកាត់ខ្សែវីស
ដងបង្វិលដែកកាត់ខ្សែវីសខាងក្នុងដងបង្វិលដែកកាត់ខ្សែវីសខាងក្នុង
ស្វានដៃស្វានដៃ
5

Assemble and test

Screw the burner tube onto the elbow-piece and screw the 3/8 in. tube, 1 1/2 in. long, into the side opening. Push the india-rubber tube from the gas supply onto the side tube and light. A purplish-blue flame means air and gas are in the right proportion. A yellow tip means too much gas: plug the hole in the jet slightly.

សម្ភារៈសម្រាប់ជំហាននេះ៖

បំពង់លង្ហិនអង្កត់ផ្ចិតក្រៅ ៩,៥ មីលីម៉ែត្របំពង់លង្ហិនអង្កត់ផ្ចិតក្រៅ ៩,៥ មីលីម៉ែត្រ1 1 1/2 in.

ឧបករណ៍ដែលត្រូវការ៖

បំពង់កៅស៊ូបំពង់កៅស៊ូ
6

Fit the air collar

If the gas burns with a green flame and a hissing noise, the air-holes are too large. Cut sheet brass about 3/4 in. wide and 1 3/4 in. long and drill two holes 3/8 in. across, 1/2 in. from each end (their centres 3/16 in. further in). Turn it into a tube and push it onto the burner tube over the air-holes. Turn it until the two sets of holes do not quite match, so the right amount of air reaches the burner.

សម្ភារៈសម្រាប់ជំហាននេះ៖

សន្លឹកស្ពាន់លឿងសន្លឹកស្ពាន់លឿង1 3/4 x 1 3/4 in.

ឧបករណ៍ដែលត្រូវការ៖

កន្ត្រៃកាត់សន្លឹកលោហៈកន្ត្រៃកាត់សន្លឹកលោហៈ
ស្វានដៃស្វានដៃ

សម្ភារៈ

8

ឧបករណ៍ចាំបាច់

6

CC0 សាធារណៈ

ប្លង់នេះត្រូវបានចេញផ្សាយក្រោម CC0។ អ្នកមានសិទ្ធិចម្លង កែប្រែ ចែកចាយ និងប្រើប្រាស់ដោយមិនចាំបាច់សុំអនុញ្ញាត។

គាំទ្រអ្នកបង្កើតដោយទិញផលិតផលតាមរយៈប្លង់របស់ពួកគេ ដែលពួកគេទទួលបាន កម្រៃជើងសារអ្នកបង្កើត កំណត់ដោយអ្នកលក់ ឬបង្កើតកំណែថ្មីនៃប្លង់នេះ ហើយបញ្ចូលជាការតភ្ជាប់ក្នុងប្លង់របស់អ្នកដើម្បីចែករំលែកចំណូល។

ការពិភាក្សា

(0)

ចូល ដើម្បីចូលរួមពិភាក្សា

កំពុងផ្ទុកមតិ...