កិច្ចសហប្រតិបត្តិការ
សិល្បៈ
សម្រស់ និង សុខុមាលភាព
សិប្បកម្ម
វប្បធម៌ និង ប្រវត្តិសាស្ត្រ
ការកម្សាន្ត
បរិស្ថាន
ម្ហូប និង ភេសជ្ជៈ
វិស្វកម្មបញ្ច្រាស
វិទ្យាសាស្ត្រ
កីឡា
បច្ចេកវិទ្យា
ប្រដាប់ដែលស្លៀក

Foot-Fed Carriage Saw Table: The Saw Rides on Balls Under the Table, a Foot Lever Pulls It Through the Work (Hall, 1933)
Harry O. Hall of Murray, Utah, received US 1,930,168, dated 10 October 1933, for a portable saw table where the saw moves and the work stays still. The saw and its motor hang from a carriage under the top. The carriage rolls on balls in V-shaped tracks in a straight line. A foot lever pulls it back through a board held against the fence, and springs bring it forward again. Nuts on a hanging stem set the depth, and a spring under the motor keeps the belts tight. The table rolls on wheels and its back legs fold.
The patent gives no sizes; every size here is ours, and our top is plywood where his is folded sheet metal.
កម្រិតខ្ពស់
About 1 week
ការណែនាំ
1
1
The foot lever, the travel and the cut
The foot lever, the travel and the cut
កំពុងផ្ទុកសៀវភៅ Jupyter…
2
2
Read US 1,930,168
Read US 1,930,168
"The movable saw carriage is mounted to freely move longitudinally of the table in a straight line and is moved into engagement with the piece of work held in position by the work fence, when the lever 29' is depressed by the foot."
3
3
Table and legs
Table and legs
Make the top 5 of 18 mm plywood 1000 x 600 mm with pine aprons 6, 7 round it, and cut a slot 47 12 mm wide and 500 mm long down its middle. Fix four pine legs 9, 10 splayed outwards at the corners with braces 11 and plywood gussets 12, the top 850 mm high; bolt the rear legs' gussets with one bolt each as a pivot and a second removable bolt, so they fold. Put an axle 15 between the front legs with a wheel 14 on each end.
សម្ភារៈសម្រាប់ជំហាននេះ៖
សន្លឹកឈើបន្ទះ1 ដុំ
ឈើស្រល់កាត់រួច6 ដុំ
ដែកថែបទន់មូល1 ដុំ
សំណុំកង់កៅស៊ូ1 ដុំ
ប៊ូឡុងក្បាលមូល8 ដុំ
វីសឈើ40 ដុំ
កាវឈើ1 ដុំឧបករណ៍ដែលត្រូវការ៖
រណាររាង (ជីកសោ)
ស្វានឥតខ្សែ
សំណុំក្បាលខួង
ឈ្នាប់ដងវែង
ជ្រុងវាស់រួម
ខ្សែវាស់4
4
Tracks and carriage
Tracks and carriage
Screw a pine rail 22 along each side under the top and bolt a length of steel angle on it, V upwards, as the track 21. Make the carriage of two more angles 16, V downwards over the tracks, joined near each end by a cross bolt 17 with nuts 19 either side of each angle, so their spacing can be set. Under each end of each carriage angle, between the bolt and a small steel lug 23 bolted inside the angle, put a 10 mm steel ball 20 to roll in the track. Hook two springs 24 from the front wall of the top to the front cross bolt.
សម្ភារៈសម្រាប់ជំហាននេះ៖
ឈើស្រល់កាត់រួច1 ដុំ
ដែកជ្រុងពីដែកទន់2 ដុំ
ការប្រមូលផ្ដុំប៊ូឡុងប្រាំមួយជ្រុង12 ដុំ
ដងវីស (ដងខ្សែវីស)1 ដុំ
ខ្ចៅប្រាំមួយជ្រុង8 ដុំ
ដែកបន្ទះរាបថែបទន់1 ដុំ
រ៉ូលម៉ង់គ្រាប់1 ដុំ
រ៉ឺស័រទាញ2 ដុំ
វីសឈើ16 ដុំឧបករណ៍ដែលត្រូវការ៖
រណារកាត់ដែក
ម៉ាស៊ីនកិនមុំ
ម៉ាស៊ីនចោះឈរ
សំណុំក្បាលខួង
សំណុំដែកឆាប
ដង្កាប់តុ
សោរបង្វិលកែតម្រូវបាន
វ៉ែនតាសុវត្ថិភាព5
5
Foot lever and chain
Foot lever and chain
Pivot a hardwood foot lever 29' on the front axle, reaching back along the floor, with a pedal 31 on its free end. Fix a pulley 28 on a shaft 29 between the rear legs. Run a chain 27 from the rear cross bolt of the carriage over the pulley and down to the lever, fixed 450 mm from its pivot. Pressing the pedal pulls the carriage back; letting go, the springs return it.
សម្ភារៈសម្រាប់ជំហាននេះ៖
ក្តារឈើរឹង1 ដុំ
រ៉ក1 ដុំ
ដែកថែបទន់មូល1 ដុំ
ខ្សែច្រវាក់រ៉ូឡែ1 ដុំ
ការប្រមូលផ្ដុំប៊ូឡុងប្រាំមួយជ្រុង3 ដុំឧបករណ៍ដែលត្រូវការ៖
រណាររាង (ជីកសោ)
ស្វានឥតខ្សែ
សំណុំក្បាលខួង
រណារកាត់ដែក
សោរបង្វិលកែតម្រូវបាន6
6
Saw frame, arbor and shield
Saw frame, arbor and shield
Bolt a rectangle of steel angle as the saw frame 32. Hang one end on the rear cross bolt between two collars 33 with set screws 34, so it can be slid sideways. On the front cross bolt put a sleeve 35 between collars 36 with a threaded stem 38 hanging from it, through a hole 39 in the frame's end, with a clamping nut 40 above and below: these set the saw's height. Bolt two flange bearings 42 across the frame and fit a 30 mm arbor 43 turned with a collar, a loose flange and an M20 thread; put the 250 mm blade on one end, centred under the slot, and a V-belt pulley 49 on the other. Bend a sheet steel shield 48 round the lower half of the blade and bolt it to the frame.
សម្ភារៈសម្រាប់ជំហាននេះ៖
ដែកជ្រុងពីដែកទន់1 ដុំ
ដែកថែបទន់មូល2 ដុំ
វីសរឹតក្បាលរូងចាន4 ដុំ
ដងវីស (ដងខ្សែវីស)1 ដុំ
ខ្ចៅប្រាំមួយជ្រុង4 ដុំ
ប៊ែរីងប្រភេទហ្វ្លង់2 ដុំ
Circular Saw Blade Set1 ដុំ
រ៉ក់ខ្សែក្រវាត់រាងវី (មុខកាត់ A)1 ដុំ
សន្លឹកដែកថែបទន់1 ដុំ
ការប្រមូលផ្ដុំប៊ូឡុងប្រាំមួយជ្រុង10 ដុំឧបករណ៍ដែលត្រូវការ៖
រណារកាត់ដែក
ម៉ាស៊ីនកិនមុំ
ម៉ាស៊ីនចោះឈរ
សំណុំក្បាលខួង
ឈុតកាត់ខ្សែវីស
ដងបង្វិលដែកកាត់ខ្សែវីសខាងក្នុង
ម៉ាស៊ីនកាត់ដែក (ទ័រ)
ក្បាលចាប់ម៉ាស៊ីនក្លឹងបីក្រញាំ
ឧបករណ៍កាត់ម៉ាស៊ីនកិន
ជញ្ជីងវាស់ឌីជីថល ៦ អ៊ីញ
កន្ត្រៃកាត់សន្លឹកលោហៈ
ដង្កាប់តុ
សោរបង្វិលកែតម្រូវបាន
សំណុំកូនសោប្រាំមួយជ្រុង7
7
Motor frame
Motor frame
Bolt a shorter angle frame 53 inside the saw frame, pivoted on the same rear cross bolt, and bolt the motor 51 under it with a V-belt pulley 50 in line with the arbor's. Hang its free end from a bolt 55 off a sleeve 56 on a rod 57 across the saw frame, with a spring 61 and washer 62 on the bolt above the motor frame and a nut 59 below. Fit the belt 52 and set its tension with the nut. Have the motor wired to a switch at the front.
សម្ភារៈសម្រាប់ជំហាននេះ៖
ដែកជ្រុងពីដែកទន់1 ដុំ
ម៉ូទ័រអគ្គិសនី1 ដុំ
រ៉ក់ខ្សែក្រវាត់រាងវី (មុខកាត់ A)1 ដុំ
ខ្សែក្រវាត់រាង V (ផ្នែក A)1 ដុំ
ដែកថែបទន់មូល1 ដុំ
ដងវីស (ដងខ្សែវីស)1 ដុំ
Coil Spring1 ដុំ
រ៉ុនដែលរាបស្មើ2 ដុំ
ខ្ចៅប្រាំមួយជ្រុង2 ដុំ
ការប្រមូលផ្ដុំប៊ូឡុងប្រាំមួយជ្រុង6 ដុំ
កុងតាក់បើក/បិទ1 ដុំឧបករណ៍ដែលត្រូវការ៖
រណារកាត់ដែក
ម៉ាស៊ីនចោះឈរ
សំណុំក្បាលខួង
សោរបង្វិលកែតម្រូវបាន
សំណុំកូនសោប្រាំមួយជ្រុង8
8
Fence and first cut
Fence and first cut
Fix a hardwood fence 63 across the top near its rear end, standing past both sides, held by hook bolts 64 that hook under steel flanges 66 screwed to the gussets, with nuts 67. Set the blade 10 mm above the board's thickness with the stem's nuts. Hold a board against the fence, start the motor and press the pedal: the saw comes back through the board. Let the pedal up and it returns.
សម្ភារៈសម្រាប់ជំហាននេះ៖
ក្តារឈើរឹង1 ដុំ
ដងវីស (ដងខ្សែវីស)1 ដុំ
ខ្ចៅប្រាំមួយជ្រុង2 ដុំ
ដែកបន្ទះរាបថែបទន់1 ដុំ
វីសឈើ8 ដុំឧបករណ៍ដែលត្រូវការ៖
រណាររាង (ជីកសោ)
ស្វានឥតខ្សែ
សំណុំក្បាលខួង
ជ្រុងវាស់រួម
វ៉ែនតាសុវត្ថិភាព
ឧបករណ៍ការពារត្រចៀក (គម្របត្រចៀក SNR ៣០ dB)9
9
Troubleshooting
Troubleshooting
Carriage saw troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**Harry O. Hall** of Murray, Utah, US 1,930,168, dated 10 October 1933, filed 21 March 1933. He claimed a top with a longitudinal slot, "a traveling carriage mounted beneath said top and movable longitudinally thereof", a saw frame pivoted on one cross bar and hung from the other on a stem with nuts above and below, and a motor frame hung from the saw frame on a bolt with a spring. His top is folded sheet metal on splayed legs; ours is plywood on pine. His balls are confined between the cross bolts and lugs; ours the same, in steel angle. He gives no sizes; every size here is ours.
សម្ភារៈ
27- 1 ដុំកន្លែងទុក
- 6 ដុំកន្លែងទុក
- 2 ដុំកន្លែងទុក
- 1 ដុំកន្លែងទុក
- 8 ដុំកន្លែងទុក
- 64 ដុំកន្លែងទុក
- 1 ដុំកន្លែងទុក
- 2 ដុំកន្លែងទុក
- កន្លែងទុក
- 1 ដុំកន្លែងទុក
- 16 ដុំកន្លែងទុក
- 1 ដុំកន្លែងទុក
- 1 ដុំកន្លែងទុក
- 2 ដុំកន្លែងទុក
- 1 ដុំកន្លែងទុក
- 1 ដុំកន្លែងទុក
- 1 ដុំកន្លែងទុក
- 4 ដុំកន្លែងទុក
- 2 ដុំកន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- 1 ដុំកន្លែងទុក
- 1 ដុំកន្លែងទុក
- កន្លែងទុក
- 1 ដុំកន្លែងទុក
- 2 ដុំកន្លែងទុក
- 1 ដុំកន្លែងទុក
ឧបករណ៍ចាំបាច់
22- 1 vendor sell this, none ship to you yetកន្លែងទុក
- 1 vendor sell this, none ship to you yetកន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- 1 vendor sell this, none ship to you yetកន្លែងទុក
- កន្លែងទុក
- 1 vendor sell this, none ship to you yetកន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
ប្លង់នេះធ្វើ
ប្លង់ពាក់ព័ន្ធ
ប្លង់ទាំងនេះចែករំលែកចំណេះដឹង — បច្ចេកទេស សម្ភារៈ ឬគោលការណ៍

Portable Bench Saw: A Lift-Out Power Unit on Trunnions, Its Motor on Spring Bars, Under a Tilting Platform (Henkel, 1928)
ដោយ Forge
ការធ្វើការឈើ
9
0
0
0
0
0

Twin-Saw Table: A Rip Saw and a Crosscut Saw at Opposite Corners, One Motor, Each Depth Set by Tilting the Top (Gottschalk, 1926)
ដោយ Forge
ការធ្វើការឈើ
8
0
0
0
0
0
CC0 សាធារណៈ
ប្លង់នេះត្រូវបានចេញផ្សាយក្រោម CC0។ អ្នកមានសិទ្ធិចម្លង កែប្រែ ចែកចាយ និងប្រើប្រាស់ដោយមិនចាំបាច់សុំអនុញ្ញាត។
គាំទ្រអ្នកបង្កើតដោយទិញផលិតផលតាមរយៈប្លង់របស់ពួកគេ ដែលពួកគេទទួលបាន កម្រៃជើងសារអ្នកបង្កើត កំណត់ដោយអ្នកលក់ ឬបង្កើតកំណែថ្មីនៃប្លង់នេះ ហើយបញ្ចូលជាការតភ្ជាប់ក្នុងប្លង់របស់អ្នកដើម្បីចែករំលែកចំណូល។
