កិច្ចសហប្រតិបត្តិការ
សិល្បៈ
សម្រស់ និង សុខុមាលភាព
សិប្បកម្ម
វប្បធម៌ និង ប្រវត្តិសាស្ត្រ
ការកម្សាន្ត
បរិស្ថាន
ម្ហូប និង ភេសជ្ជៈ
វិស្វកម្មបញ្ច្រាស
វិទ្យាសាស្ត្រ
កីឡា
បច្ចេកវិទ្យា
ប្រដាប់ដែលស្លៀក
Instant-Read Thermometer: Digital, with a Stainless Probe That Pivots on the Case (Cook, US 5,018,875, 1991)
Penny

បង្កើតដោយ

Penny

3. វិច្ឆិកា 2026DK
11
0
0
0
0

Instant-Read Thermometer: Digital, with a Stainless Probe That Pivots on the Case (Cook, US 5,018,875, 1991)

A pocket digital thermometer. A thin stainless steel probe with a thermistor in its tip pivots on a small, flat-sided case, so you can push the probe into food and turn the display to face you. A button cell runs a chip and a liquid crystal display, and a push button updates the reading at once. The angled case will not roll off a table. Result: a thin-probe digital thermometer for food and air. Source: T. A. Cook (PSG Industries), US 5,018,875 (1991). Unknown: the circuit, the range, the case size. Picture: the patent drawing.
មធ្យម
Unknown

ការណែនាំ

1

Make the probe

Cut a type 304 stainless steel tube about 0.166 in (4.0 mm) across and 5 in (120 mm) long, and close one end. Set a thermistor inside the closed tip and run its two wires up the tube. Aluminium or titanium would also serve.

សម្ភារៈសម្រាប់ជំហាននេះ៖

បំពង់ដែកអ៊ីណុកបំពង់ដែកអ៊ីណុក1 probe
ឈុតធឺមីស្ទ័រ NTCឈុតធឺមីស្ទ័រ NTC1 thermistor
ខ្សែស្ពាន់ខ្សែស្ពាន់1 interconnecting wires

ឧបករណ៍ដែលត្រូវការ៖

រណារកាត់ដែករណារកាត់ដែក
ដែកផ្សារដែកផ្សារ
2

Mould the pivot boss and case

Mould from ABS a cylindrical pivot boss with a recess for the probe's open end and a channel right through it for the wires. Mould the case in an upper and a lower half that snap together, wider at the display end and tapering to the probe end so it cannot roll, with two projecting supports at the probe end, each with a pivot hole. Not given: the sizes.

សម្ភារៈសម្រាប់ជំហាននេះ៖

គ្រាប់ ABSគ្រាប់ ABS1 boss and case

ឧបករណ៍ដែលត្រូវការ៖

ម៉ាស៊ីនចាក់ប្លាស្ទិកម៉ាស៊ីនចាក់ប្លាស្ទិក
វិមាត្រមិនស្គាល់វិមាត្រមិនស្គាល់
3

Fit the electronics and assemble

In the case, fit an integrated circuit that turns the thermistor's resistance into a reading on a liquid crystal display at the wide end, with a push button beside it that updates the reading at once. Add a compartment for a 1.5 V button cell (Eveready E675, IEC R07) under a cover that locks with a quarter turn. Push the probe into the boss, lead the wires through the channel to the circuit, and clamp the boss ends in the pivot holes as the halves snap together; friction holds whatever angle you set. In use, push the probe in, turn the display to face you and press the button. Not given: the circuit (the patent points to US 4,536,851).

សម្ភារៈសម្រាប់ជំហាននេះ៖

បន្ទះសៀគ្វីបោះពុម្ពបន្ទះសៀគ្វីបោះពុម្ព1 ដុំ
សៀគ្វីរួមបញ្ចូលសៀគ្វីរួមបញ្ចូល1 ដុំ
អេក្រង់ LCD ជាផ្នែកអេក្រង់ LCD ជាផ្នែក1 ដុំ
ប៊ូតុងចុចប៊ូតុងចុច1 ដុំ
ថ្មប៊ូតុង 1.5 វ៉ុលថ្មប៊ូតុង 1.5 វ៉ុល1 ដុំ
ខ្សែសំណផ្សារខ្សែសំណផ្សារ1 as needed

ឧបករណ៍ដែលត្រូវការ៖

ដែកផ្សារដែកផ្សារ

សម្ភារៈ

10

ឧបករណ៍ចាំបាច់

4

ប្លង់ពាក់ព័ន្ធ

ប្លង់ទាំងនេះចែករំលែកចំណេះដឹង — បច្ចេកទេស សម្ភារៈ ឬគោលការណ៍

CC0 សាធារណៈ

ប្លង់នេះត្រូវបានចេញផ្សាយក្រោម CC0។ អ្នកមានសិទ្ធិចម្លង កែប្រែ ចែកចាយ និងប្រើប្រាស់ដោយមិនចាំបាច់សុំអនុញ្ញាត។

គាំទ្រអ្នកបង្កើតដោយទិញផលិតផលតាមរយៈប្លង់របស់ពួកគេ ដែលពួកគេទទួលបាន កម្រៃជើងសារអ្នកបង្កើត កំណត់ដោយអ្នកលក់ ឬបង្កើតកំណែថ្មីនៃប្លង់នេះ ហើយបញ្ចូលជាការតភ្ជាប់ក្នុងប្លង់របស់អ្នកដើម្បីចែករំលែកចំណូល។

ការពិភាក្សា

(0)

ចូល ដើម្បីចូលរួមពិភាក្សា

កំពុងផ្ទុកមតិ...