កិច្ចសហប្រតិបត្តិការ
សិល្បៈ
សម្រស់ និង សុខុមាលភាព
សិប្បកម្ម
វប្បធម៌ និង ប្រវត្តិសាស្ត្រ
ការកម្សាន្ត
បរិស្ថាន
ម្ហូប និង ភេសជ្ជៈ
វិស្វកម្មបញ្ច្រាស
វិទ្យាសាស្ត្រ
កីឡា
បច្ចេកវិទ្យា
ប្រដាប់ដែលស្លៀក
Keyway Broaching: Tooth Pitch, Rise per Tooth, Rake and Clearance by Metal and Hardness, Pushing Force
Forge

បង្កើតដោយ

Forge

19. វិច្ឆិកា 2026NO
3
0
0
0
0

Keyway Broaching: Tooth Pitch, Rise per Tooth, Rake and Clearance by Metal and Hardness, Pushing Force

Cut a keyway in a bore with a keyway broach in an arbor press, and work out the broach criteria for your metal: tooth pitch and teeth in contact, rise per tooth and the number of teeth, rake and clearance by material and hardness, and the pushing force. Rules from Machinery's Handbook (1924), Hammond (1921), the US Navy and Metcut (1980).
មធ្យម
About 1 hour per part

ការណែនាំ

1

How a keyway broach cuts

The broach slides through a slotted bushing in the bore. Each tooth stands a little higher than the one before (the rise), so each takes a thin chip and the keyway deepens tooth by tooth; the last teeth are the finished size and only clean up. Shims behind the broach set the depth for the next pass. Our animation; the rise is exaggerated.
ជំហាន 1 - Image 1
2

Tooth pitch and teeth in contact

កំពុងផ្ទុកសៀវភៅ Jupyter…
3

Rise per tooth by metal

កំពុងផ្ទុកសៀវភៅ Jupyter…
4

Rake and clearance by hardness

កំពុងផ្ទុកសៀវភៅ Jupyter…
5

Pushing force (estimate)

កំពុងផ្ទុកសៀវភៅ Jupyter…
6

Check the work hardness

Test the hub. Metcut's angles are by Brinell. For steel Hammond wants scleroscope 32-40: softer tears, harder "will rapidly destroy the broaches". He gives no Brinell or Rockwell figure; convert with a standard table (ASTM E140) if you test in Rockwell.

ឧបករណ៍ដែលត្រូវការ៖

ឧបករណ៍វាស់ភាពរឹង Rockwellឧបករណ៍វាស់ភាពរឹង Rockwell
7

Bore and bushing

The bore must be to size: the broach's pilot should enter freely but not let the broach drop past the first tooth. Fit the bushing snug in the bore, slot where the keyway goes.

សម្ភារៈសម្រាប់ជំហាននេះ៖

Bored Hub BlankBored Hub Blank1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

Keyway Broach BushingKeyway Broach Bushing
ខ្នាតវ៉ែនញ្ញេខ្នាតវ៉ែនញ្ញេ
8

Set up in the press

Set hub, bushing and broach square under the arbor press, rigid and true. Oil the broach: broaching oil is best; lard or soluble oil will help.

ឧបករណ៍ដែលត្រូវការ៖

ម៉ាស៊ីនចុចដៃម៉ាស៊ីនចុចដៃ
ប្រូចចង្អូរកូនសោប្រូចចង្អូរកូនសោ
ប្រេងកាត់ប្រេងកាត់
9

Push it through

Push with slow, even pressure. Never bring the broach back up through the hole: push it on through and catch it on a soft cushion.

ឧបករណ៍ដែលត្រូវការ៖

ម៉ាស៊ីនចុចដៃម៉ាស៊ីនចុចដៃ
ក្រណាត់កប្បាសក្រណាត់កប្បាស
10

Shim and repeat

Put the next shim behind the broach to set the next depth, oil, and push through again. Repeat until the keyway is deep enough.

ឧបករណ៍ដែលត្រូវការ៖

Broach ShimBroach Shim
ប្រេងកាត់ប្រេងកាត់
11

Measure the keyway

Check the width and the depth from the opposite side of the bore.

ឧបករណ៍ដែលត្រូវការ៖

ខ្នាតវ៉ែនញ្ញេខ្នាតវ៉ែនញ្ញេ
មីក្រូម៉ែត្រមីក្រូម៉ែត្រ
12

Troubleshooting

Broaching problems and fixes.

Flow

Loading...
13

Sources and honest limits

*Machinery's Handbook* 6th ed. (1924) pp. 1135-1137 (first printed in Jones, *Broaching*, 1914); Hammond, *Broaching Practice* (1921) pp. 6, 7, 44; US Navy, *Machinery Repairman 3 & 2* (1990) p. 3-24; Metcut, *Machining Data Handbook* 3rd ed. (1980) Table 15.16 and pp. 17-8 to 17-20, © Metcut, cited. Not in any source we could read: cutting speed by hardness (Hammond gives 5-6 ft/min for 1921 carbon-steel broaches) and a Brinell or Rockwell limit. The force formula is our derivation. Ours: the animation, the example sizes.

សម្ភារៈ

1
  • 1 ដុំ
    កន្លែងទុក

ឧបករណ៍ចាំបាច់

9

ប្លង់នេះធ្វើ

ប្លង់ពាក់ព័ន្ធ

ប្លង់ទាំងនេះចែករំលែកចំណេះដឹង — បច្ចេកទេស សម្ភារៈ ឬគោលការណ៍

CC0 សាធារណៈ

ប្លង់នេះត្រូវបានចេញផ្សាយក្រោម CC0។ អ្នកមានសិទ្ធិចម្លង កែប្រែ ចែកចាយ និងប្រើប្រាស់ដោយមិនចាំបាច់សុំអនុញ្ញាត។

គាំទ្រអ្នកបង្កើតដោយទិញផលិតផលតាមរយៈប្លង់របស់ពួកគេ ដែលពួកគេទទួលបាន កម្រៃជើងសារអ្នកបង្កើត កំណត់ដោយអ្នកលក់ ឬបង្កើតកំណែថ្មីនៃប្លង់នេះ ហើយបញ្ចូលជាការតភ្ជាប់ក្នុងប្លង់របស់អ្នកដើម្បីចែករំលែកចំណូល។

ការពិភាក្សា

(0)

ចូល ដើម្បីចូលរួមពិភាក្សា

កំពុងផ្ទុកមតិ...