កិច្ចសហប្រតិបត្តិការ
សិល្បៈ
សម្រស់ និង សុខុមាលភាព
សិប្បកម្ម
វប្បធម៌ និង ប្រវត្តិសាស្ត្រ
ការកម្សាន្ត
បរិស្ថាន
ម្ហូប និង ភេសជ្ជៈ
វិស្វកម្មបញ្ច្រាស
វិទ្យាសាស្ត្រ
កីឡា
បច្ចេកវិទ្យា
ប្រដាប់ដែលស្លៀក

Kitchen Funnel with Air-Vent Ribs, 3D Printed in PETG
A 120 mm kitchen funnel for bottling wine, cider or juice, printed in one piece in PETG. Three small ribs along the outside of the spout hold it off the bottle neck so air can come out while the liquid goes in, so it pours without glugging. A common, open design; all sizes are ours, and we have not printed or tested it yet.
ចាប់ផ្តើម
About 4 hours, mostly printing
ការណែនាំ
1
1
Our funnel's numbers
Our funnel's numbers
កំពុងផ្ទុកសៀវភៅ Jupyter…
2
2
Make it fit your bottles
Make it fit your bottles
Optional: change TOP_D or the spout sizes and run it in FreeCAD: OUT=. TOP_D= freecadcmd build_all.py
build_all.pypython
ឧបករណ៍ដែលត្រូវការ៖
ជញ្ជីងវាស់ឌីជីថល ៦ អ៊ីញ3
3
Print the funnel
Print the funnel
Print it rim down on the bed, no supports; the cone and spout grow upward. PETG sold for food contact, a stainless steel nozzle (brass nozzles can contain lead), 0.2 mm layers, at least 3 walls.
សម្ភារៈសម្រាប់ជំហាននេះ៖
សរសៃ PETG60 ក្រឧបករណ៍ដែលត្រូវការ៖
ម៉ាស៊ីនបោះពុម្ព 3D ប្រើខ្សែ (FDM)
ឈុតក្បាលចាក់របស់ម៉ាស៊ីនបោះពុម្ព 3D4
4
Clean it up
Clean it up
Trim any strings or blobs, especially inside the spout and between the ribs. Check the spout is clear.
ឧបករណ៍ដែលត្រូវការ៖
កាំបិតសិប្បកម្ម5
5
Check the fit
Check the fit
Put the spout into a bottle: the ribs should touch the neck and leave gaps between them. Pour water through and watch it run without glugging.

ឧបករណ៍ដែលត្រូវការ៖
ដបកញ្ចក់មានឆ្នុក
ទឹក6
6
Sanitise
Sanitise
Soak it in no-rinse sanitiser mixed as its label says. Do not boil it: PETG softens at about 80 °C.
ឧបករណ៍ដែលត្រូវការ៖
ថ្នាំសម្លាប់មេរោគ
ទឹក7
7
Troubleshooting
Troubleshooting
Funnel problems and fixes.
Flow
Loading...
8
8
Honest limits
Honest limits
A common, open design, drawn by us in FreeCAD; every size is ours. The ribs were checked by slicing the model; the funnel has not been printed or poured through by us yet. Sanitise before every use and replace it when scratched.
ឧបករណ៍ចាំបាច់
7- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
ឯកសាររចនា
1ប្លង់នេះធ្វើ
ប្លង់ពាក់ព័ន្ធ
ប្លង់ទាំងនេះចែករំលែកចំណេះដឹង — បច្ចេកទេស សម្ភារៈ ឬគោលការណ៍
CC0 សាធារណៈ
ប្លង់នេះត្រូវបានចេញផ្សាយក្រោម CC0។ អ្នកមានសិទ្ធិចម្លង កែប្រែ ចែកចាយ និងប្រើប្រាស់ដោយមិនចាំបាច់សុំអនុញ្ញាត។
គាំទ្រអ្នកបង្កើតដោយទិញផលិតផលតាមរយៈប្លង់របស់ពួកគេ ដែលពួកគេទទួលបាន កម្រៃជើងសារអ្នកបង្កើត កំណត់ដោយអ្នកលក់ ឬបង្កើតកំណែថ្មីនៃប្លង់នេះ ហើយបញ្ចូលជាការតភ្ជាប់ក្នុងប្លង់របស់អ្នកដើម្បីចែករំលែកចំណូល។




