កិច្ចសហប្រតិបត្តិការ
សិល្បៈ
សម្រស់ និង សុខុមាលភាព
សិប្បកម្ម
វប្បធម៌ និង ប្រវត្តិសាស្ត្រ
ការកម្សាន្ត
បរិស្ថាន
ម្ហូប និង ភេសជ្ជៈ
វិស្វកម្មបញ្ច្រាស
វិទ្យាសាស្ត្រ
កីឡា
បច្ចេកវិទ្យា
ប្រដាប់ដែលស្លៀក
Perforated Screen Plate: Clear- or Buhr-Punched Steel Plate (Richards, Ore Dressing, 1903)
Forge

បង្កើតដោយ

Forge

4. វិច្ឆិកា 2026NO
8
0
0
0
0

Perforated Screen Plate: Clear- or Buhr-Punched Steel Plate (Richards, Ore Dressing, 1903)

The punched steel screens of ore mills: round holes or slots punched through steel plate, either 'clear punched' with a sharp square-edged tool that cuts out a wad, or 'buhr punched' with a thicker tool that tears the metal over a socket in the die. Clear punching suits holes of 0.03 inch and up; buhr punching suits fine holes of 0.02 inch and less, because a thicker plate can be used. Holes in rows at 60° give 1.154 times the open area of rows at 90°. Unknown: the plate thickness and hole spacing for a given screen. Source: R. H. Richards, Ore Dressing vol. I (1903), pp. 167-168. Picture: p. 167 with Figs. 117 and 118.
មធ្យម
Unknown

ការណែនាំ

1

Choose the holes

For coarse work use round holes of 0.04 inch (1 mm) and up; for medium work about 0.03 inch (0.75 mm), clear punched. For fine work, 0.02 inch (0.5 mm) and less, buhr punch, so a thicker plate can be used. The smallest practical clear-punched hole is about 0.014 inch (0.35 mm) wide: a hole much narrower than the plate is thick breaks the punch (the extreme Richards found was a slot 54 per cent of the thickness).

សម្ភារៈសម្រាប់ជំហាននេះ៖

សន្លឹកដែកសន្លឹកដែក1 steel plate
វិមាត្រមិនស្គាល់វិមាត្រមិនស្គាល់1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

ម៉ាស៊ីនចុចចោះម៉ាស៊ីនចុចចោះ
2

Lay out the holes

Set round holes in rows at 60° or 90°; with the same hole and spacing, 60° rows give 1.154 times the open area. Punch slots vertical, diagonal or horizontal, in line or staggered; staggering spreads the punching strain.

ឧបករណ៍ដែលត្រូវការ៖

ម៉ាស៊ីនចុចចោះម៉ាស៊ីនចុចចោះ
3

Punch the plate

Clear punching: a tool with a square, sharp edge cuts out a wad exactly the size and shape of the hole. Buhr punching: a thicker tool presses the plate, lying on a socket in the die, just deep enough to tear the metal apart.

ឧបករណ៍ដែលត្រូវការ៖

ម៉ាស៊ីនចុចចោះម៉ាស៊ីនចុចចោះ

សម្ភារៈ

2

ឧបករណ៍ចាំបាច់

1

CC0 សាធារណៈ

ប្លង់នេះត្រូវបានចេញផ្សាយក្រោម CC0។ អ្នកមានសិទ្ធិចម្លង កែប្រែ ចែកចាយ និងប្រើប្រាស់ដោយមិនចាំបាច់សុំអនុញ្ញាត។

គាំទ្រអ្នកបង្កើតដោយទិញផលិតផលតាមរយៈប្លង់របស់ពួកគេ ដែលពួកគេទទួលបាន កម្រៃជើងសារអ្នកបង្កើត កំណត់ដោយអ្នកលក់ ឬបង្កើតកំណែថ្មីនៃប្លង់នេះ ហើយបញ្ចូលជាការតភ្ជាប់ក្នុងប្លង់របស់អ្នកដើម្បីចែករំលែកចំណូល។

ការពិភាក្សា

(0)

ចូល ដើម្បីចូលរួមពិភាក្សា

កំពុងផ្ទុកមតិ...