កិច្ចសហប្រតិបត្តិការ
សិល្បៈ
សម្រស់ និង សុខុមាលភាព
សិប្បកម្ម
វប្បធម៌ និង ប្រវត្តិសាស្ត្រ
ការកម្សាន្ត
បរិស្ថាន
ម្ហូប និង ភេសជ្ជៈ
វិស្វកម្មបញ្ច្រាស
វិទ្យាសាស្ត្រ
កីឡា
បច្ចេកវិទ្យា
ប្រដាប់ដែលស្លៀក
Platform Scale: Four Knife-Edge Hinges and Two Levers to a Steelyard (Fairbanks, 1831)
Mark

បង្កើតដោយ

Mark

2. វិច្ឆិកា 2026FI
9
0
0
0
0

Platform Scale: Four Knife-Edge Hinges and Two Levers to a Steelyard (Fairbanks, 1831)

A scale for wagons and carts, reading the same wherever the load stands. Erastus and Thaddeus Fairbanks of St. Johnsbury, Vermont, patented it in 1831. A plank platform nine by twelve feet rests on four knife-edge hinges, one at each corner, and two levers gather the load from all four onto one rod. The rod pulls on an ordinary steelyard, which then reads only a tenth or a twentieth of the load. Result: a platform scale reading ten times (or twenty times) what the steelyard shows, the same wherever the load stands on the platform. Source: E. & T. Fairbanks, US Patent No. 118 (1837), restating their patent of 13 June 1831. Unknown: the material and sizes of the hinges, knife-edges, fulcra and levers. Picture: patent drawing.
កម្រិតខ្ពស់
1 week

ការណែនាំ

1

Build the frame

Lay two timber bed-sills, about 10 inches square and 16 feet long, parallel and about 7 feet apart. Bolt two end timbers, 8 by 14 inches and 12 feet long, across them near their ends. Just inside the end timbers, lay the two rockers, 8 inches square and 9 feet long, with their tops flush with the end timbers. Ours: carriage bolts.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ឈើកាត់ជាការ៉េឈើកាត់ជាការ៉េ6 2 sills, 2 end timbers, 2 rockers
ប៊ូឡុងក្បាលមូលប៊ូឡុងក្បាលមូល1 ឈុត

ឧបករណ៍ដែលត្រូវការ៖

រណារឆ្លងកាត់សម្រាប់មនុស្សពីរនាក់រណារឆ្លងកាត់សម្រាប់មនុស្សពីរនាក់
ដែកចោះដីដែកចោះដី
ញញួរញញួរ
2

Fit the four knife-edge hinges

Bolt a hinge firmly under each end of each rocker, one at every corner of the machine. Each hinge carries two knife-edges. One rests on a fulcrum standing on the bed-sill; the other reaches out to carry the platform. Set every knife-edge parallel to the others: knife-edges at an angle cramp and bind. Not given: the material and size of the hinges, knife-edges and fulcra.

សម្ភារៈសម្រាប់ជំហាននេះ៖

សម្ភារៈមិនស្គាល់សម្ភារៈមិនស្គាល់1 4 hinges, 8 knife-edges, 4 fulcra
ប៊ូឡុងក្បាលមូលប៊ូឡុងក្បាលមូល1 ឈុត

ឧបករណ៍ដែលត្រូវការ៖

ដែកចោះដីដែកចោះដី
វិមាត្រមិនស្គាល់វិមាត្រមិនស្គាល់
3

Join the levers

Run a horizontal lever from each rocker. The longer lever reaches across nearly to the opposite rocker. The shorter one ends at a point equally far from the axes of both, and hangs there from the longer lever by a chain, rod or stirrup, so the two act as one. From the end of the longer lever a rod rises straight up to a steelyard hung from a fixed support. With the two knife-edges of each hinge 6 inches apart and the rod hung 60 inches from the lever's axis, the load is ten times the steelyard reading; at 120 inches it is twenty times. Not given: the lever material. Ours: an iron chain and a wrought iron rod.

សម្ភារៈសម្រាប់ជំហាននេះ៖

សម្ភារៈមិនស្គាល់សម្ភារៈមិនស្គាល់1 2 levers
ច្រវាក់ដែកច្រវាក់ដែក1 lever link
ដងដែកលត់ដងដែកលត់1 rod to the steelyard
ជញ្ជីងដងកូនទម្ងន់រំកិលជញ្ជីងដងកូនទម្ងន់រំកិល1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

វិមាត្រមិនស្គាល់វិមាត្រមិនស្គាល់
4

Lay the platform

Lay two timbers, short enough to pass freely between the rockers, parallel over the bed-sills. Spike stout planks 9 feet long across them, making a platform of about 9 by 12 feet. Under these timbers fasten iron plates that rest on the inner knife-edges of the hinges. Ours: nails as the spikes.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ឈើកាត់ជាការ៉េឈើកាត់ជាការ៉េ2 platform timbers
ក្ដារឈើកាត់ក្ដារឈើកាត់1 for 9 x 12 ft
បន្ទះដែកបន្ទះដែក4 ដុំ
ដែកគោលដែកគោល1 as needed

ឧបករណ៍ដែលត្រូវការ៖

រណារឆ្លងកាត់សម្រាប់មនុស្សពីរនាក់រណារឆ្លងកាត់សម្រាប់មនុស្សពីរនាក់
ញញួរញញួរ

សម្ភារៈ

9

ឧបករណ៍ចាំបាច់

4

សម្ភារៈប្លង់ដែលបានភ្ជាប់

ប្លង់ពាក់ព័ន្ធ

ប្លង់ទាំងនេះចែករំលែកចំណេះដឹង — បច្ចេកទេស សម្ភារៈ ឬគោលការណ៍

CC0 សាធារណៈ

ប្លង់នេះត្រូវបានចេញផ្សាយក្រោម CC0។ អ្នកមានសិទ្ធិចម្លង កែប្រែ ចែកចាយ និងប្រើប្រាស់ដោយមិនចាំបាច់សុំអនុញ្ញាត។

គាំទ្រអ្នកបង្កើតដោយទិញផលិតផលតាមរយៈប្លង់របស់ពួកគេ ដែលពួកគេទទួលបាន កម្រៃជើងសារអ្នកបង្កើត កំណត់ដោយអ្នកលក់ ឬបង្កើតកំណែថ្មីនៃប្លង់នេះ ហើយបញ្ចូលជាការតភ្ជាប់ក្នុងប្លង់របស់អ្នកដើម្បីចែករំលែកចំណូល។

ការពិភាក្សា

(0)

ចូល ដើម្បីចូលរួមពិភាក្សា

កំពុងផ្ទុកមតិ...