សិល្បៈ
សម្រស់ និង សុខុមាលភាព
សិប្បកម្ម
វប្បធម៌ និង ប្រវត្តិសាស្ត្រ
ការកម្សាន្ត
បរិស្ថាន
ម្ហូប និង ភេសជ្ជៈ
អនាគតបៃតង
វិស្វកម្មបញ្ច្រាស
វិទ្យាសាស្ត្រ
កីឡា
បច្ចេកវិទ្យា
ប្រដាប់ដែលស្លៀក

Making a Clay Ocarina — A Vessel Flute You Can Play
Join two clay pinch-pots into a hollow chamber, cut a whistle mouthpiece and poke finger holes to build an ocarina — a vessel flute whose pitch comes from the whole body of air, not the length of a tube. A buildable ceramics school project in Helmholtz resonance, the physics of blowing across a bottle.
ចាប់ផ្តើម
45 minutes
ការណែនាំ
1
1
A hollow egg full of sound
A hollow egg full of sound
An ocarina is a vessel flute: a sealed hollow clay chamber with a whistle mouthpiece and finger holes. Unlike a pipe, its note comes from the whole body of air inside.
2
2
Prepare the clay
Prepare the clay
Knead a fist-sized ball of clay firmly to press out every air bubble, so it will not crack later.
Materials for this step:
Earthenware Clay300 g3
3
Make two pinch-pots
Make two pinch-pots
Press the clay into two equal thumb-pots (little bowls) with even walls about 8 mm thick.
4
4
Join into a hollow chamber
Join into a hollow chamber
Score and wet both rims, then press the two bowls together into a sealed hollow ball. The chamber must be completely airtight.
Tools needed:
Clay Scoring Tool5
5
Smooth the seam
Smooth the seam
Smooth the joint all the way round with a wet finger so no air can leak from the seam.
6
6
Cut the windway
Cut the windway
Add a short clay spout and cut a narrow flat channel through it — the windway — that aims a thin ribbon of breath into the chamber.
Tools needed:
Clay Cutting Wire & Knife Set7
7
Cut the sounding edge
Cut the sounding edge
Just past the windway, cut a small rectangular opening with one sharp, clean edge (the labium). The air splits on this edge to make the sound.
Tools needed:
Clay Cutting Wire & Knife Set8
8
Test the whistle
Test the whistle
Blow gently through the windway while the clay is still soft. Trim the sharp edge until you get a clear, steady whistle.
9
9
Poke the finger holes
Poke the finger holes
Make four to six finger holes in the top with a pencil or skewer. On an ocarina, hole SIZE sets the pitch far more than hole position.
10
10
Dry it slowly
Dry it slowly
Let the ocarina dry slowly for several days, away from direct heat, until it is bone-dry and pale — rushing this cracks the walls.
11
11
Fire it
Fire it
Fire the bone-dry ocarina in a kiln to harden it and brighten the tone. For a no-kiln class, use air-dry clay instead and skip firing.
12
12
Play and tune
Play and tune
Cover all holes for the lowest note and open them to rise. If a note sounds flat, carefully enlarge that hole a little to raise its pitch.
13
13
Compendium — the Helmholtz resonator
Compendium — the Helmholtz resonator
An ocarina is not a pipe — it is a Helmholtz resonator, the same physics as blowing across a bottle. The whole cushion of air inside the chamber springs in and out through the open holes, like a mass bouncing on a spring. Its pitch depends on two things: the VOLUME of the chamber and the TOTAL AREA of all the open holes — not on where the holes are. Opening a hole, or a bigger hole, lets air escape more easily, which stiffens the spring and raises the pitch; this is why ocarina holes can sit wherever your fingers fall, unlike a tube flute where each hole's position fixes its note. The sound itself is an edge-tone: the flat ribbon of breath from the windway flaps back and forth across the sharp labium edge, the very same mechanism that sounds a recorder or an organ flue pipe. Vessel flutes are ancient and worldwide — Mesoamerican clay ocarinas, the Chinese xun, and countless clay whistles — and the simplest vessel flute of all is just a clay whistle with no finger holes.
សម្ភារៈ
1- 300 gកន្លែងទុក
ឧបករណ៍ចាំបាច់
2- កន្លែងទុក
- កន្លែងទុក
You can swap these in
Can't get one of the materials? Swap it for an equivalent — these work just as well.
- Instead of Earthenware Clay, try:
Refractory Clay
Kaolin Clay Powder
Wild Clay
Porcelain Clay - Instead of Clay Scoring Tool, try:
Belt Stamping Tool Set
Deburring Tool Kit
Lathe Tool Set (HSS, 8-Piece)
Digging Tool (Stone / Antler / Stick)
Lathe Cutting Tool
Crimp Tool - Instead of Clay Cutting Wire & Knife Set, try:
Blunt Collection Knife
Gilder's Knife
ប្លង់ពាក់ព័ន្ធ
ប្លង់ទាំងនេះចែករំលែកចំណេះដឹង — បច្ចេកទេស សម្ភារៈ ឬគោលការណ៍
Related blueprints
Other builds that share materials, tools, or techniques with this one.

Making a Clay Crucible for Smelting — The Vessel That Holds Molten MetalMetalworking

Making a Bamboo Recorder — A Fipple Flute with a Full Scale

Making a Quena — The Notched Flute of the Andes

Making a Glass Bead on a Mandrel — Lampwork BeadmakingGlassworking

Knapping an Obsidian Blade — Pressure-Flaked Volcanic Glassstoneworking

Making Biochar from Agricultural Waste — Carbon Sequestration You Can Holdsustainability
CC0 សាធារណៈ
ប្លង់នេះត្រូវបានចេញផ្សាយក្រោម CC0។ អ្នកមានសិទ្ធិចម្លង កែប្រែ ចែកចាយ និងប្រើប្រាស់ដោយមិនចាំបាច់សុំអនុញ្ញាត។
គាំទ្រអ្នកបង្កើតដោយទិញផលិតផលតាមរយៈប្លង់របស់ពួកគេ ដែលពួកគេទទួលបាន កម្រៃជើងសារអ្នកបង្កើត កំណត់ដោយអ្នកលក់ ឬបង្កើតកំណែថ្មីនៃប្លង់នេះ ហើយបញ្ចូលជាការតភ្ជាប់ក្នុងប្លង់របស់អ្នកដើម្បីចែករំលែកចំណូល។