កិច្ចសហប្រតិបត្តិការ
សិល្បៈ
សម្រស់ និង សុខុមាលភាព
សិប្បកម្ម
វប្បធម៌ និង ប្រវត្តិសាស្ត្រ
ការកម្សាន្ត
បរិស្ថាន
ម្ហូប និង ភេសជ្ជៈ
វិស្វកម្មបញ្ច្រាស
វិទ្យាសាស្ត្រ
កីឡា
បច្ចេកវិទ្យា
ប្រដាប់ដែលស្លៀក

Swing-Nut Tubing Cutter: Swing the Blade Support Down and the Jaw Slides to the Tube, Up and the Screw Feeds It (Pritchard, 1941)
Frank L. Pritchard of Parker, Arizona, received US 2,231,593, dated 11 February 1941, for a tubing cutter small enough for a mechanic's tool box. The tube sits in a V in a fixed jaw. A movable jaw slides on the adjusting screw and a guide pin, with a spring pushing the jaws apart. The cutting wheel is held by a pivoted support with threads on its inner edge. Swung down, the support lets go of the screw, so the jaw can be pushed straight onto any tube. Swung up, it meshes with the screw again and the screw feeds the wheel in.
We make his parts from steel bar and plate. All sizes are ours.
មធ្យម
About 3 days
ការណែនាំ
1
1
The swing that lets go
The swing that lets go
កំពុងផ្ទុកសៀវភៅ Jupyter…
2
2
Read US 2,231,593
Read US 2,231,593
"The pivoted blade support 16 may swing downwardly until the threads thereof will be free of the threads of the screw 8. The movable jaw 6 may now be slid downwardly until the pivoted blade support is in its proper cutting position."
3
3
Print the template
Print the template
Both jaws, the blade support, the wheel and a 15 mm tube at 1:1, with the screw, pin and pivot holes. print at 100 % (check the 50 mm bar).
4
4
Make the stationary jaw
Make the stationary jaw
Saw 64 mm of 16 mm square bar, or of 16 mm plate. File the 90 degree V 8 mm deep in its top face. Drill the 6 mm pin hole and a 10 mm hole for the screw, and counterbore the pin hole 10 mm across, 5 mm deep, for the spring. Drill the 3 mm cross-pin hole across the jaw so it just cuts into the side of the screw hole.
សម្ភារៈសម្រាប់ជំហាននេះ៖
បន្ទះដែកថែបទន់1 ដុំឧបករណ៍ដែលត្រូវការ៖
រណារកាត់ដែក
សំណុំដែកឆាប
ម៉ាស៊ីនចោះឈរ
ដង្កាប់ម៉ាស៊ីន
សំណុំក្បាលខួង
ដែកគូសចំណុចកណ្តាល
ដែកគូស
ដង្កាប់តុ
ជញ្ជីងវាស់ឌីជីថល ៦ អ៊ីញ5
5
Make the movable jaw and the support
Make the movable jaw and the support
Saw the movable jaw 50 mm long from the same bar. Drill the 6.2 mm pin hole and its spring counterbore. Saw and file a slot 8.2 mm wide down its middle, from 22 mm to the end. Saw the blade support from 14 mm plate to the template. File its upper part down to 8 mm thick, centred, so it slides into the slot, and file away its lower inner corner. Saw a 7 mm slot up its lower part for the wheel. Drill the pivot and stop-pin holes through the jaw and support together, and file the stop-pin hole in the support into a short slot.
សម្ភារៈសម្រាប់ជំហាននេះ៖
បន្ទះដែកថែបទន់1 ដុំឧបករណ៍ដែលត្រូវការ៖
រណារកាត់ដែក
សំណុំដែកឆាប
សំណុំដែកឆាបម្ជុល
ម៉ាស៊ីនចោះឈរ
ដង្កាប់ម៉ាស៊ីន
សំណុំក្បាលខួង
ដង្កាប់តុ
ជញ្ជីងវាស់ឌីជីថល ៦ អ៊ីញ6
6
Tap the half nut
Tap the half nut
Pin the support in the jaw, swung up, and clamp it there. Drill 6.8 mm down the screw axis through both, so the drill cuts a shallow groove in the support's inner edge, then tap it M8 through both. Take the support out and open the jaw's own hole to 8.5 mm, so the screw passes freely and only the support's threads hold it.
ឧបករណ៍ដែលត្រូវការ៖
ម៉ាស៊ីនចោះឈរ
ដង្កាប់ម៉ាស៊ីន
សំណុំក្បាលខួង
ឈុតកាត់ខ្សែវីស
ប្រេងកាត់7
7
Make the screw and the guide pin
Make the screw and the guide pin
Turn the top 62 mm of a 90 mm piece of 10 mm bar to 8 mm and cut an M8 thread on it with the die. Turn a groove 1.5 mm deep and 3.2 mm wide in the plain part, where the cross pin will sit, and drill a 6 mm hole across its bottom end for a T-bar. Cut the guide pin, 80 mm of 6 mm rod, and drill a 3 mm hole across its top for the stop pin.
សម្ភារៈសម្រាប់ជំហាននេះ៖
ដែកថែបទន់មូល1 ដុំ
ដែកទន់ដុំមូល1 ដុំឧបករណ៍ដែលត្រូវការ៖
ម៉ាស៊ីនកាត់ដែក (ទ័រ)
ក្បាលចាប់ម៉ាស៊ីនក្លឹងបីក្រញាំ
ឧបករណ៍កាត់ម៉ាស៊ីនកិន
ដែកកាត់ដាច់ (ម៉ាស៊ីនកិន)
ឈុតកាត់ខ្សែវីស
ម៉ាស៊ីនចោះឈរ
សំណុំក្បាលខួង
រណារកាត់ដែក
ជញ្ជីងវាស់ឌីជីថល ៦ អ៊ីញ8
8
Turn the cutting wheel
Turn the cutting wheel
Chuck a tool steel bar and face it. Turn the end to 20 mm across for 10 mm, centre drill and drill a 5 mm hole 10 mm deep, and turn the edge to a 50 degree vee, 25 degrees each side, sharp in the middle of the 6 mm width. Part it off 6 mm long and take the burr off the hole.
សម្ភារៈសម្រាប់ជំហាននេះ៖
ដែកថែបឧបករណ៍ជាដុំមូល1 ដុំឧបករណ៍ដែលត្រូវការ៖
ម៉ាស៊ីនកាត់ដែក (ទ័រ)
ក្បាលចាប់ម៉ាស៊ីនក្លឹងបីក្រញាំ
ឧបករណ៍កាត់ម៉ាស៊ីនកិន
ដែកកាត់ដាច់ (ម៉ាស៊ីនកិន)
ឈុតដែកខួងកណ្តាល
សំណុំក្បាលខួង
ជញ្ជីងវាស់ឌីជីថល ៦ អ៊ីញ
វ៉ែនតាសុវត្ថិភាព9
9
Harden and temper
Harden and temper
Heat the wheel to a cherry red, until a magnet no longer sticks, and quench it in water, moving it about. Rub it bright with a stone, warm it on a piece of steel plate over the fire, and quench again as soon as it turns a light straw colour.
ឧបករណ៍ដែលត្រូវការ៖
ឡជាងដែក
ដង្កាប់ជាងដែក
មេដែកតូច
ធុងជ្រលក់ត្រជាក់
ទឹក
ថ្មសំលៀង
ស្រោមដៃផ្សារ
វ៉ែនតាសុវត្ថិភាព10
10
Assemble
Assemble
Drive the guide pin into the stationary jaw. Put the screw into its hole from below and drive the cross pin in so it lies in the groove; the screw must still turn. Fit the T-bar. Slip the spring over the guide pin, then the movable jaw over the pin and the screw, and put the stop pin across the top. Fit the wheel in the support on its 5 mm pin, and pin the support into the jaw with its pivot and stop pins. Rivet a 1.5 mm steel strip along the top of the jaw, sticking out past the support as a thumb piece. Oil the threads.
សម្ភារៈសម្រាប់ជំហាននេះ៖
ស្នៀតដែកភ្ជាប់5 ដុំ
សំណុំរ៉ឺស័របង្ហាប់1 ដុំ
បន្ទះដែកស្ព្រីង1 ដុំ
ដែកគោលដែកថែប2 ដុំ
ដែកទន់ដុំមូល1 ដុំឧបករណ៍ដែលត្រូវការ៖
ញញួរក្បាលមូល
ដែកគូសចំណុចកណ្តាល
ដង្កាប់តុ
ម៉ាស៊ីនចោះឈរ
សំណុំក្បាលខួង
ប្រេងកាត់11
11
Cut a copper tube
Cut a copper tube
Mark a copper tube and hold it in a vice with soft jaws, or by hand for small tubes. Swing the support down, push the movable jaw down until the wheel touches the tube in the V, swing it up into the screw, and tighten the screw a little. Turn the cutter once round, give the screw about a quarter turn, and go on until the tube parts. The wheel should run in its own groove; the end should be square and not squeezed oval. Clean the inside of the end with a deburring tool.
សម្ភារៈសម្រាប់ជំហាននេះ៖
បំពង់ស្ពាន់1 ដុំឧបករណ៍ដែលត្រូវការ៖
ដង្កាប់តុ
ឧបករណ៍ដកសំណល់គែម
ជញ្ជីងវាស់ឌីជីថល ៦ អ៊ីញ12
12
Troubleshooting
Troubleshooting
Swing-nut tubing cutter troubleshooting.
Flow
Loading...
13
13
History and honest limits
History and honest limits
**Frank L. Pritchard** of Parker, Arizona, US 2,231,593, dated 11 February 1941, filed 17 November 1939. He claimed "a pivoted blade support mounted on the movable jaw and having threads on the inner edge thereof adapted to engage the threads of said screw". His movable jaw had a bushing for the guide pin and a looped handle on the screw head; ours has a drilled hole and a T-bar. The patent gives no sizes or materials; all of ours are ours.
សម្ភារៈ
9- 1 ដុំកន្លែងទុក
- 1 ដុំកន្លែងទុក
- 1 ដុំកន្លែងទុក
- 1 ដុំកន្លែងទុក
- 5 ដុំកន្លែងទុក
- 1 ដុំកន្លែងទុក
- 1 ដុំកន្លែងទុក
- 2 ដុំកន្លែងទុក
- 1 ដុំកន្លែងទុក
ឧបករណ៍ចាំបាច់
27- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
ឯកសាររចនា
1ប្លង់នេះធ្វើ
ប្លង់ពាក់ព័ន្ធ
ប្លង់ទាំងនេះចែករំលែកចំណេះដឹង — បច្ចេកទេស សម្ភារៈ ឬគោលការណ៍

V-Slide Tubing Cutter: Two Slide Halves Held on the Ways by One Spring Clip, a Reamer on the Frame (Thewes, 1938)
ដោយ Forge
ការធ្វើការលោហៈ
13
0
0
0
0
0

Taps and Dies Cut on the Lathe, with Wrench and Stock
ដោយ Martin
ការធ្វើការលោហៈ
29
0
0
0
6
0

Reamer: a Fluted Hand Reamer Turned, Fluted, Hardened and Stoned (Markham, 1908)
ដោយ Forge
ការធ្វើការលោហៈ
15
0
0
0
0
0
CC0 សាធារណៈ
ប្លង់នេះត្រូវបានចេញផ្សាយក្រោម CC0។ អ្នកមានសិទ្ធិចម្លង កែប្រែ ចែកចាយ និងប្រើប្រាស់ដោយមិនចាំបាច់សុំអនុញ្ញាត។
គាំទ្រអ្នកបង្កើតដោយទិញផលិតផលតាមរយៈប្លង់របស់ពួកគេ ដែលពួកគេទទួលបាន កម្រៃជើងសារអ្នកបង្កើត កំណត់ដោយអ្នកលក់ ឬបង្កើតកំណែថ្មីនៃប្លង់នេះ ហើយបញ្ចូលជាការតភ្ជាប់ក្នុងប្លង់របស់អ្នកដើម្បីចែករំលែកចំណូល។
