កិច្ចសហប្រតិបត្តិការ
សិល្បៈ
សម្រស់ និង សុខុមាលភាព
សិប្បកម្ម
វប្បធម៌ និង ប្រវត្តិសាស្ត្រ
ការកម្សាន្ត
បរិស្ថាន
ម្ហូប និង ភេសជ្ជៈ
វិស្វកម្មបញ្ច្រាស
វិទ្យាសាស្ត្រ
កីឡា
បច្ចេកវិទ្យា
ប្រដាប់ដែលស្លៀក
Ring Stand: a Brass Rod on a Board Foot with Sliding Rings (Faraday, 1830)
Charlie

បង្កើតដោយ

Charlie

7. វិច្ឆិកា 2026DE
10
0
0
0
0

Ring Stand: a Brass Rod on a Board Foot with Sliding Rings (Faraday, 1830)

A stand that holds flasks and basins at any height over a lamp or furnace. Michael Faraday (1830) describes the retort-stand: an upright brass rod on a heavy foot, with rings of several sizes, each on an arm whose socket slides up and down the rod and is fixed by a screw-nut at the back. Brass feet filled with lead tip over under a heavy vessel, so he makes the foot a stout board about 12 x 6 x 1 inches, the rod fixed 1 1/2 inches from one end, and stands the lamp or furnace on the board under the ring. Source: M. Faraday, Chemical Manipulation (1830), §386, p. 175. Picture: his woodcut.
ចាប់ផ្តើម
Unknown

ការណែនាំ

1

Read Faraday

"It is much better to make the foot of a piece of stout board, about twelve inches in length, six inches in width, and an inch thick. The upright rod should be fixed about one inch and a half from one end of it, the lamp or furnace should be placed upon it, and the ring of course in a corresponding direction. Such an arrangement is perfectly steady, and cannot be overset by any weight which it is strong enough to bear."
2

Fix the rod in the board

Take a stout board about 12 in. long, 6 in. wide and 1 in. thick. Fix an upright brass rod in it about 1 1/2 in. from one end. Rod size, and how it is fixed, are not given (unknown). Ours: a hardwood board.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ក្តារឈើរឹងក្តារឈើរឹង1 ហ្វីត
ដុំស្ពាន់លឿងដុំស្ពាន់លឿង1 upright
ឧបករណ៍តភ្ជាប់មិនស្គាល់ឧបករណ៍តភ្ជាប់មិនស្គាល់1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

វិមាត្រមិនស្គាល់វិមាត្រមិនស្គាល់
3

Make the rings

Make several rings of different sizes, each fixed to an arm, and each arm to a socket that slides freely up and down the rod. Fit each socket with a screw-nut at the back to tighten it at any height. The metal and sizes are not given (unknown). Ours: wing nuts for the screw-nuts.

សម្ភារៈសម្រាប់ជំហាននេះ៖

លោហៈមិនស្គាល់លោហៈមិនស្គាល់1 rings, arms, sockets
ខ្ចៅស្លាបមេអំបៅខ្ចៅស្លាបមេអំបៅ1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

វិមាត្រមិនស្គាល់វិមាត្រមិនស្គាល់
4

Use it

Stand the lamp or furnace on the board and turn the ring over it. Slide the ring to the height wanted and tighten the screw. Do not set a hot flask on a cold ring, or a cold, freshly filled flask on a hot ring over the fire: the bottom may come out (Faraday §388).

សម្ភារៈ

5

ឧបករណ៍ចាំបាច់

1

CC0 សាធារណៈ

ប្លង់នេះត្រូវបានចេញផ្សាយក្រោម CC0។ អ្នកមានសិទ្ធិចម្លង កែប្រែ ចែកចាយ និងប្រើប្រាស់ដោយមិនចាំបាច់សុំអនុញ្ញាត។

គាំទ្រអ្នកបង្កើតដោយទិញផលិតផលតាមរយៈប្លង់របស់ពួកគេ ដែលពួកគេទទួលបាន កម្រៃជើងសារអ្នកបង្កើត កំណត់ដោយអ្នកលក់ ឬបង្កើតកំណែថ្មីនៃប្លង់នេះ ហើយបញ្ចូលជាការតភ្ជាប់ក្នុងប្លង់របស់អ្នកដើម្បីចែករំលែកចំណូល។

ការពិភាក្សា

(0)

ចូល ដើម្បីចូលរួមពិភាក្សា

កំពុងផ្ទុកមតិ...