កិច្ចសហប្រតិបត្តិការ
សិល្បៈ
សម្រស់ និង សុខុមាលភាព
សិប្បកម្ម
វប្បធម៌ និង ប្រវត្តិសាស្ត្រ
ការកម្សាន្ត
បរិស្ថាន
ម្ហូប និង ភេសជ្ជៈ
វិស្វកម្មបញ្ច្រាស
វិទ្យាសាស្ត្រ
កីឡា
បច្ចេកវិទ្យា
ប្រដាប់ដែលស្លៀក
Screw Eye: Parmelee's One-Piece Wire Eye with a Stop-Ring
Forge

បង្កើតដោយ

Forge

26. តុលា 2026NO
26
0
0
0
0

Screw Eye: Parmelee's One-Piece Wire Eye with a Stop-Ring

A screw eye bent from one piece of wire, by Arthur W. Parmelee of Worcester, Massachusetts (US 350,209, 1886). One end is threaded to turn into wood, the other bent into a closed eye. His addition is a ring closed into a groove around the shank: it stops the screw at the right depth, looks neat, and is left a little loose so the eye can turn without marking the wood under it. The patent gives no metal or sizes. Iron wire, the 3 mm size, the pliers and the die are ours. The picture: Figs. 1-3 and 10-11 of the patent.
ចាប់ផ្តើម
30 minutes

ការណែនាំ

1

Cut a piece of wire

Cut a straight piece of iron wire about 3 mm thick (ours), long enough for the screw, the shank and the eye (Fig. 1).

សម្ភារៈសម្រាប់ជំហាននេះ៖

លួសដែកទាញលួសដែកទាញ1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

បន្ទាត់បន្ទាត់
ដង្កាប់កាត់លួសទ្រេតដង្កាប់កាត់លួសទ្រេត
2

Cut the groove

File a narrow groove right round the wire, a screw length from one end (Fig. 2). Parmelee cuts it or presses it in.

ឧបករណ៍ដែលត្រូវការ៖

សំណុំដែកឆាបម្ជុលសំណុំដែកឆាបម្ជុល
ដង្កាប់តុដង្កាប់តុ
3

Point the screw end

File that end to a tapering point (Fig. 3).

ឧបករណ៍ដែលត្រូវការ៖

ដែកឆាបលោហៈដែកឆាបលោហៈ
ដង្កាប់តុដង្កាប់តុ
4

Thread the screw end

Cut a screw thread on the pointed end "in the usual way". Ours: a die in a die stock, run on as far as the point allows.

ឧបករណ៍ដែលត្រូវការ៖

ដងកាន់ដែកកាត់ខ្សែវីសខាងក្រៅដងកាន់ដែកកាត់ខ្សែវីសខាងក្រៅ
ដង្កាប់តុដង្កាប់តុ
5

Bend the eye

Bend the other end into a closed round eye, the end turned in against the shank (Fig. 10).

ឧបករណ៍ដែលត្រូវការ៖

តង់មាត់មូលតង់មាត់មូល
ដង្កាប់មាត់រាបដង្កាប់មាត់រាប
6

Make the split ring

Bend a short piece of the same wire round into an open ring that just slips over the shank (Figs. 9 and 11).

សម្ភារៈសម្រាប់ជំហាននេះ៖

លួសដែកទាញលួសដែកទាញ1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

ដង្កាប់កាត់លួសទ្រេតដង្កាប់កាត់លួសទ្រេត
តង់មាត់មូលតង់មាត់មូល
7

Close the ring into the groove

Slide the ring onto the groove and squeeze it until its two ends meet in a continuous band. Leave it a little loose, so the eye turns while the ring stays still against the wood.

ឧបករណ៍ដែលត្រូវការ៖

ដង្កាប់មាត់រាបដង្កាប់មាត់រាប
8

Turn it into the wood

Turn the screw into the wood by the eye until the ring meets the surface: the ring is the depth stop. Parmelee also allows washers under the ring; we leave them out.

សម្ភារៈ

1

ឧបករណ៍ចាំបាច់

8

ប្លង់ពាក់ព័ន្ធ

ប្លង់ទាំងនេះចែករំលែកចំណេះដឹង — បច្ចេកទេស សម្ភារៈ ឬគោលការណ៍

CC0 សាធារណៈ

ប្លង់នេះត្រូវបានចេញផ្សាយក្រោម CC0។ អ្នកមានសិទ្ធិចម្លង កែប្រែ ចែកចាយ និងប្រើប្រាស់ដោយមិនចាំបាច់សុំអនុញ្ញាត។

គាំទ្រអ្នកបង្កើតដោយទិញផលិតផលតាមរយៈប្លង់របស់ពួកគេ ដែលពួកគេទទួលបាន កម្រៃជើងសារអ្នកបង្កើត កំណត់ដោយអ្នកលក់ ឬបង្កើតកំណែថ្មីនៃប្លង់នេះ ហើយបញ្ចូលជាការតភ្ជាប់ក្នុងប្លង់របស់អ្នកដើម្បីចែករំលែកចំណូល។

ការពិភាក្សា

(0)

ចូល ដើម្បីចូលរួមពិភាក្សា

កំពុងផ្ទុកមតិ...