សិល្បៈ
សម្រស់ និង សុខុមាលភាព
សិប្បកម្ម
វប្បធម៌ និង ប្រវត្តិសាស្ត្រ
ការកម្សាន្ត
បរិស្ថាន
ម្ហូប និង ភេសជ្ជៈ
វិស្វកម្មបញ្ច្រាស
វិទ្យាសាស្ត្រ
កីឡា
បច្ចេកវិទ្យា
ប្រដាប់ដែលស្លៀក
The Finger-Valve Fountain Bath Brush: Press to Run, Let Go to Stop
YourGrandma

បង្កើតដោយ

YourGrandma

6. តុលា 2026IS
31
0
0
0
0

The Finger-Valve Fountain Bath Brush: Press to Run, Let Go to Stop

A bath brush fed from a hose runs all the time, or needs a tap out of reach. Daniel S. Koons and William F. Moughler of Chicago received US 634,527, dated 10 October 1899, for "a fountain bath-brush": a false back with a water passage, joined to the brush by a hollow screw whose perforated head lets the water out among the bristles, with a valve that a spring and the water pressure hold shut until a finger presses its stem, and a strap that holds the hand to the brush. This rung works out the finger force, then builds the false back on a scrub brush with a tyre valve as the finger valve, and measures the force and the flow.
មធ្យម
About 3 hours

ការណែនាំ

1

Force to open the valve

កំពុងផ្ទុកសៀវភៅ Jupyter…
2

A brush that feeds itself before it

The embedded blueprint feeds soap from inside a shaving brush. Koons and Moughler feed water, and give the finger a valve to start and stop it.
3

Read US 634,527

"Said valve is held normally closed by means of a spring 9 and also by the water-pressure, as will be obvious." "A strap k is secured at the sides of said back B' and passes over the latter, so that by inserting the hand between said back B' and said strap k the brush can be firmly held and the fingers at the same time kept in position to operate the valve."
4

Bore the false back

Cut a hardwood block 120 × 50 × 22 mm. Drill a 6 mm passage 90 mm along its centre from one end, and a 6 mm hole down from the top to meet it 30 mm from the far end.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ដុំឈើរឹងដុំឈើរឹង1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

ដង្កាប់តុដង្កាប់តុ
ស្វានឥតខ្សែស្វានឥតខ្សែ
ឈុតក្បាលស្វាន់មានចំណុចកណ្ដាលឈុតក្បាលស្វាន់មានចំណុចកណ្ដាល
បន្ទាត់បន្ទាត់
វ៉ែនតាសុវត្ថិភាពថ្លាវ៉ែនតាសុវត្ថិភាពថ្លា
5

Fit the finger valve

Drill a hole across the passage 20 mm from the inlet to take a tyre valve, pin upward. Epoxy it in so the water must pass through it.

សម្ភារៈសម្រាប់ជំហាននេះ៖

វ៉ាល់កង់វ៉ាល់កង់1 ដុំ
អេប៉ុកស៊ីពីរផ្នែកអេប៉ុកស៊ីពីរផ្នែក1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

ស្វានឥតខ្សែស្វានឥតខ្សែ
សំណុំក្បាលខួងសំណុំក្បាលខួង
6

Join it to the brush

Drill a 6 mm hole through the scrub brush's back to line up with the outlet. Cut a rubber gasket, and screw the block on with four wood screws.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ច្រាសដុសច្រាសដុស1 ដុំ
សន្លឹកកៅស៊ូសន្លឹកកៅស៊ូ1 ដុំ
វីសឈើ #8 × ១ អ៊ីញវីសឈើ #8 × ១ អ៊ីញ1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

ស្វានឥតខ្សែស្វានឥតខ្សែ
សំណុំក្បាលខួងសំណុំក្បាលខួង
កាំបិតសិប្បកម្មកាំបិតសិប្បកម្ម
ឈុតទួណឺវីសឈុតទួណឺវីស
7

Strap and hose

Screw a strip of rubber sheet across the block as a hand strap, over the valve's side. Fit a hose connector to the inlet with brass fittings and PTFE tape.

សម្ភារៈសម្រាប់ជំហាននេះ៖

សន្លឹកកៅស៊ូសន្លឹកកៅស៊ូ1 ដុំ
វីសឈើ #8 × ១ អ៊ីញវីសឈើ #8 × ១ អ៊ីញ1 ដុំ
គ្រឿងភ្ជាប់លង្ហិនគ្រឿងភ្ជាប់លង្ហិន1 ដុំ
ខ្សែបិទខ្សែរបត់ PTFEខ្សែបិទខ្សែរបត់ PTFE1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

ឈុតទួណឺវីសឈុតទួណឺវីស
សោរបង្វិលកែតម្រូវបានសោរបង្វិលកែតម្រូវបាន
8

The patent drawing

US 634,527 drawing sheet, public domain (expired patent).
ជំហាន 8 - Image 1
9

Measure force and flow

Connect the garden hose and turn on the tap. Press the valve pin with the force meter's hook until water runs; note the force. Hold it open over the jug for 30 s and read the flow.
ជំហាន 9 - Image 1

សម្ភារៈសម្រាប់ជំហាននេះ៖

ទឹកទឹក1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

ឧបករណ៍វាស់កម្លាំង (ជញ្ជីងរ៉ឺស័រ)ឧបករណ៍វាស់កម្លាំង (ជញ្ជីងរ៉ឺស័រ)
ក្អមវាស់ក្អមវាស់
នាឡិកាបញ្ឈប់នាឡិកាបញ្ឈប់
បំពង់បាញ់ទឹកសួនច្បារបំពង់បាញ់ទឹកសួនច្បារ
10

A valve that drips, sticks or barely flows

Finger-valve bath brush troubleshooting.

Flow

Loading...
11

History and honest limits

**Daniel S. Koons** and **William F. Moughler** of Chicago filed US 634,527 on 21 September 1898; it is dated 10 October 1899. They called it a self-cleansing brush. Its handle is telescopic, with a stuffing-box between the two members, and the hose can be led through it to the brush; a second form uses a nozzle as the screw joining the backs. They did not limit it to the bath. **Honest limits.** A tyre valve stands in for their seated valve and stem, and wood screws for their hollow screw. Your forces and flows are the result.

សម្ភារៈ

9

ឧបករណ៍ចាំបាច់

13

CC0 សាធារណៈ

ប្លង់នេះត្រូវបានចេញផ្សាយក្រោម CC0។ អ្នកមានសិទ្ធិចម្លង កែប្រែ ចែកចាយ និងប្រើប្រាស់ដោយមិនចាំបាច់សុំអនុញ្ញាត។

គាំទ្រអ្នកបង្កើតដោយទិញផលិតផលតាមរយៈប្លង់របស់ពួកគេ ដែលពួកគេទទួលបាន កម្រៃជើងសារអ្នកបង្កើត កំណត់ដោយអ្នកលក់ ឬបង្កើតកំណែថ្មីនៃប្លង់នេះ ហើយបញ្ចូលជាការតភ្ជាប់ក្នុងប្លង់របស់អ្នកដើម្បីចែករំលែកចំណូល។

ការពិភាក្សា

(0)

ចូល ដើម្បីចូលរួមពិភាក្សា

កំពុងផ្ទុកមតិ...