កិច្ចសហប្រតិបត្តិការ
សិល្បៈ
សម្រស់ និង សុខុមាលភាព
សិប្បកម្ម
វប្បធម៌ និង ប្រវត្តិសាស្ត្រ
ការកម្សាន្ត
បរិស្ថាន
ម្ហូប និង ភេសជ្ជៈ
វិស្វកម្មបញ្ច្រាស
វិទ្យាសាស្ត្រ
កីឡា
បច្ចេកវិទ្យា
ប្រដាប់ដែលស្លៀក
Double-Ended Scriber from a Worn Saw File: Annealed in Lime, Filed Round in a Grooved Block, Points Hardened (Thompson, Amateur Work)
Forge

បង្កើតដោយ

Forge

14. វិច្ឆិកា 2026NO
8
0
0
0
0

Double-Ended Scriber from a Worn Saw File: Annealed in Lime, Filed Round in a Grooved Block, Points Hardened (Thompson, Amateur Work)

The marking scriber Richard Thompson made for his surface gauge in Amateur Work: 1/8 in. steel or a worn-out saw file, drilled in the middle, pointed at both ends with one end bent, annealed by burying it red-hot in lime, filed round while turned in a grooved hardwood block, and the points hardened.
ចាប់ផ្តើម
Two hours

ការណែនាំ

1

Read Thompson

"A worn-out saw file will answer very well, with a hole drilled through the centre to fit the bolt and pointed at each end, one of which is bent."
2

Rough the shape

Forge a flat piece of steel about 1/8 in. (3 mm) thick, or a worn-out saw file, roughly to shape: pointed at both ends, one end bent into a short hook (his fig. 30).

សម្ភារៈសម្រាប់ជំហាននេះ៖

ដែកថែបឧបករណ៍ជាបន្ទះរាបដែកថែបឧបករណ៍ជាបន្ទះរាប1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

ឡជាងដែកឡជាងដែក
ទាំងជល់ (កំណាត់ដែក)ទាំងជល់ (កំណាត់ដែក)
ញញួរញញួរ
ដង្កៀបជាងដែកដង្កៀបជាងដែក
3

Anneal in lime

Heat it gently to a dull red and bury it in lime to cool slowly: it is then easy to file.

សម្ភារៈសម្រាប់ជំហាននេះ៖

កំបោររលត់ (កាល់ស្យូមអ៊ីដ្រូសុីត)កំបោររលត់ (កាល់ស្យូមអ៊ីដ្រូសុីត)1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

ឡជាងដែកឡជាងដែក
ដង្កៀបជាងដែកដង្កៀបជាងដែក
4

Drill and flatten

Drill a hole through the middle to fit the mounting bolt and file the flat part to an even thickness for about 1/2 in. each side of the hole.

ឧបករណ៍ដែលត្រូវការ៖

ម៉ាស៊ីនចោះឈរម៉ាស៊ីនចោះឈរ
ដង្កាប់តុដង្កាប់តុ
ដែកឆាប (ដែកឆាបដៃ)ដែកឆាប (ដែកឆាបដៃ)
5

File it round

Cut a groove along the end of a hardwood block about 3 x 2 x 1/2 in., held end up in the vice. Lay the scriber in the groove, turn it slowly toward you with the left hand and file it round with the right. File the points quite sharp.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ក្តារឈើរឹងក្តារឈើរឹង1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

រណារដៃរណារដៃ
ដង្កាប់តុដង្កាប់តុ
ដែកឆាប (ដែកឆាបដៃ)ដែកឆាប (ដែកឆាបដៃ)
6

Harden the points

Harden the points (he gives no method; ours: heat the tips to a bright red and quench in water), then touch them up on an oilstone.

ឧបករណ៍ដែលត្រូវការ៖

ឡជាងដែកឡជាងដែក
ធុងជ្រលក់ត្រជាក់ធុងជ្រលក់ត្រជាក់
ថ្មសម្លៀងថ្មសម្លៀង
7

Troubleshooting

Scriber troubleshooting.

Flow

Loading...
8

History and honest limits

From Richard Thompson, "How to Construct a Compound Microscope" III, **Amateur Work, Illustrated**, vol. III, p. 198 and fig. 30 (checked on the archive.org scan amateurworkillus03lond). He mounts the scriber on a mahogany surface gauge with three brass washers 3/4 in. across and 1/16 in. thick. The hardening method, metric figures and tools are ours.

សម្ភារៈ

3

ឧបករណ៍ចាំបាច់

10

ប្លង់ពាក់ព័ន្ធ

ប្លង់ទាំងនេះចែករំលែកចំណេះដឹង — បច្ចេកទេស សម្ភារៈ ឬគោលការណ៍

CC0 សាធារណៈ

ប្លង់នេះត្រូវបានចេញផ្សាយក្រោម CC0។ អ្នកមានសិទ្ធិចម្លង កែប្រែ ចែកចាយ និងប្រើប្រាស់ដោយមិនចាំបាច់សុំអនុញ្ញាត។

គាំទ្រអ្នកបង្កើតដោយទិញផលិតផលតាមរយៈប្លង់របស់ពួកគេ ដែលពួកគេទទួលបាន កម្រៃជើងសារអ្នកបង្កើត កំណត់ដោយអ្នកលក់ ឬបង្កើតកំណែថ្មីនៃប្លង់នេះ ហើយបញ្ចូលជាការតភ្ជាប់ក្នុងប្លង់របស់អ្នកដើម្បីចែករំលែកចំណូល។

ការពិភាក្សា

(0)

ចូល ដើម្បីចូលរួមពិភាក្សា

កំពុងផ្ទុកមតិ...