កិច្ចសហប្រតិបត្តិការ
សិល្បៈ
សម្រស់ និង សុខុមាលភាព
សិប្បកម្ម
វប្បធម៌ និង ប្រវត្តិសាស្ត្រ
ការកម្សាន្ត
បរិស្ថាន
ម្ហូប និង ភេសជ្ជៈ
វិស្វកម្មបញ្ច្រាស
វិទ្យាសាស្ត្រ
កីឡា
បច្ចេកវិទ្យា
ប្រដាប់ដែលស្លៀក

Wheelbarrow: a Small Wooden Barrow (Cassell's, 1900)
A small wooden wheelbarrow: ash hales (handles) framed with oak cross-pieces, splayed legs, a red-deal bottom and sides with a curved front board bound in hoop iron, and a 1 ft wheel of eight oak spokes and four ash felloes on an ash or oak axle.
Painted red inside and light green outside, lined in a lighter colour and black.
Source: P. N. Hasluck, Cassell's Cyclopaedia of Mechanics (1900), p. 176. Picture: the book's Figs. 1-2.
មធ្យម
Unknown
ការណែនាំ
1
1
Make the hales
Make the hales
Cut the two ash hales 3 ft 1 in long, 1 5/8 in deep by 1 1/2 in thick, the handles rising 3 3/4 in above the underside. Leave no more than 5/8 in on the faces of the hale tops; dress out 3/8 in on the face and 1/4 in underneath.
សម្ភារៈសម្រាប់ជំហាននេះ៖
ក្តារឈើអាស1 hales 3 ft 1 in x 1 5/8 x 1 1/2 inឧបករណ៍ដែលត្រូវការ៖
រណារដៃ
កាំបិតឈូសឈើដៃ
រនាសពីរដៃ2
2
Frame with oak cross-pieces
Frame with oak cross-pieces
Make the cross-pieces of oak, edges dressed off underneath. Let the hind piece's tenons, gauged 1/2 in thick, come through the hales 1 1/4 in to support the legs (Fig. 2). Pin the hales and cross-pieces tight with 3/16 in wood pins.
សម្ភារៈសម្រាប់ជំហាននេះ៖
ក្តារឈើអុកស1 ដុំ
ស្នៀតឈើ1 3/16 in pinsឧបករណ៍ដែលត្រូវការ៖
រណារមានសន្លឹកខ្នង
ដែកឆូតធ្វើរន្ធតោ
ឧបករណ៍គូសសញ្ញា
ស្វាន់ដៃវិលមានក្បាល
ឆាកវាស់មុំ3
3
Fit the legs and stays
Fit the legs and stays
Put on legs 1 1/2 in square, splayed at the top, standing 1 ft below the hales to suit a 1 ft wheel, with no more than a 1/4 in shoulder. Fasten legs to hales with 3 in bolts, heads outside. Fit four stays: two under the hales and two under the hind cross-pieces.
សម្ភារៈសម្រាប់ជំហាននេះ៖
ក្តារឈើអុកស1 legs 1 1/2 in square, stays
ប៊ូឡុងក្បាលមូល4 3 inឧបករណ៍ដែលត្រូវការ៖
រណារដៃ
ស្វាន់ដៃវិលមានក្បាល
ឈុតទួណឺវីស4
4
Bottom and sides
Bottom and sides
Put in the bottom board of 1/2 in red deal, overhanging the front cross-piece 5/8 in; paint all joints. Fit the sides to the hales, the front leaning up to 3 3/4 in beyond square; sides 9 in deep by 5/8 in thick, reduced to 8 1/4 in at the hind ends, front ends edged. Run a 3/16 in or 1/4 in bead on the edge.
សម្ភារៈសម្រាប់ជំហាននេះ៖
ក្តារឈើស្រល់1 1/2 in bottom, 5/8 in sides
ថ្នាំលាបប្រេង1 ដុំឧបករណ៍ដែលត្រូវការ៖
រណារដៃ
កាំបិតឈូសឈើដៃ
ឈុតជក់គំនូរ5
5
Front board and ironwork
Front board and ironwork
Fit the front board, of 3/4 in red deal or elm, on top of the hales and bottom board, rising in a curve 1 1/4 in above the sides. Paint the joints and nail the sides to it with 1 1/2 in cut nails; screw on the 7/8 in hoop iron with 3/4 in round-headed screws.
សម្ភារៈសម្រាប់ជំហាននេះ៖
ក្តារឈើស្រល់1 3/4 in front board
ដែកគោល1 1 1/2 in cut nails
ដែកបន្ទះរាបថែបទន់1 7/8 in hoop iron
វីសឈើ1 3/4 in round-headed
ថ្នាំលាបប្រេង1 ដុំឧបករណ៍ដែលត្រូវការ៖
រណារដៃ
ញញួរ
ឈុតទួណឺវីស
ឈុតជក់គំនូរ6
6
Make the wheel
Make the wheel
Turn an ash or oak axle 8 1/4 in long by 2 1/2 in, its ends turned down to 1 1/2 in for ferrules 1 in long; drive 3/8 in round pins into the ends to stand out 1 in. Fit eight oak spokes 3/4 in by 1/2 in and four ash felloes 1 1/4 in square, joined with four 1/4 in dowels and bevelled to take a 3/4 in by 1/8 in hoop, rounded inside.
សម្ភារៈសម្រាប់ជំហាននេះ៖
ក្តារឈើអាស1 axle and felloes
ក្តារឈើអុកស1 spokes
ដងដែកមូល1 3/8 in pins
ស្នៀតឈើ4 1/4 in
ដែកបន្ទះរាបថែបទន់1 3/4 x 1/8 in tyreឧបករណ៍ដែលត្រូវការ៖
ម៉ាស៊ីនកែងឈើ
រនាសពីរដៃ
ស្វាន់ដៃវិលមានក្បាល
ញញួរ7
7
Hang the wheel and paint
Hang the wheel and paint
Screw under each hale an iron 3/4 in broad by 1/8 in thick, long enough to pass the front cross-piece by 2 or 3 in, its eye taking the axle pin. Paint the wheel and the inside of the barrow red, the outside light green, lined in a lighter colour and black.
សម្ភារៈសម្រាប់ជំហាននេះ៖
ដែកបន្ទះរាបថែបទន់2 3/4 x 1/8 in irons
វីសឈើ1 ដុំ
ថ្នាំលាបប្រេង1 ដុំឧបករណ៍ដែលត្រូវការ៖
ឈុតទួណឺវីស
ឈុតជក់គំនូរសម្ភារៈ
10- 1 axle and felloesកន្លែងទុក
- 1 spokesកន្លែងទុក
- 4 1/4 inកន្លែងទុក
- 4 3 inកន្លែងទុក
- 1 3/4 in front boardកន្លែងទុក
- 3 ដុំកន្លែងទុក
- 1 1 1/2 in cut nailsកន្លែងទុក
- 2 3/4 x 1/8 in ironsកន្លែងទុក
- 1 ដុំកន្លែងទុក
- 1 3/8 in pinsកន្លែងទុក
ឧបករណ៍ចាំបាច់
12- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
- កន្លែងទុក
ប្លង់នេះធ្វើ
CC0 សាធារណៈ
ប្លង់នេះត្រូវបានចេញផ្សាយក្រោម CC0។ អ្នកមានសិទ្ធិចម្លង កែប្រែ ចែកចាយ និងប្រើប្រាស់ដោយមិនចាំបាច់សុំអនុញ្ញាត។
គាំទ្រអ្នកបង្កើតដោយទិញផលិតផលតាមរយៈប្លង់របស់ពួកគេ ដែលពួកគេទទួលបាន កម្រៃជើងសារអ្នកបង្កើត កំណត់ដោយអ្នកលក់ ឬបង្កើតកំណែថ្មីនៃប្លង់នេះ ហើយបញ្ចូលជាការតភ្ជាប់ក្នុងប្លង់របស់អ្នកដើម្បីចែករំលែកចំណូល។
