កិច្ចសហប្រតិបត្តិការ
សិល្បៈ
សម្រស់ និង សុខុមាលភាព
សិប្បកម្ម
វប្បធម៌ និង ប្រវត្តិសាស្ត្រ
ការកម្សាន្ត
បរិស្ថាន
ម្ហូប និង ភេសជ្ជៈ
វិស្វកម្មបញ្ច្រាស
វិទ្យាសាស្ត្រ
កីឡា
បច្ចេកវិទ្យា
ប្រដាប់ដែលស្លៀក
Cam-Lock Drill-Press Vise: Holed Steel Bed, Pinned Jaws and an Eccentric Cam (Popular Mechanics, 1920)
Forge

បង្កើតដោយ

Forge

15. វិច្ឆិកា 2026NO
7
0
0
0
0

Cam-Lock Drill-Press Vise: Holed Steel Bed, Pinned Jaws and an Eccentric Cam (Popular Mechanics, 1920)

C. H. Willey's quick-acting vise for the drill-press table (Popular Mechanics, 1920): a 1/2 x 3 in. steel bed drilled with 5/8 in. holes 7/8 in. apart and bolted down on slotted end pieces, a fixed jaw pinned into any hole, a sliding jaw kept on the bar by a riveted cross pin, and an eccentric cam on a handle that locks the work.
មធ្យម
A day

ការណែនាំ

1

The steps

កំពុងផ្ទុកសៀវភៅ Jupyter…
2

Read Willey

"A very efficient, quick-opening and closing vise for the drill-press table."
3

Make the bed

Cut a bed bar from 1/2 x 3 in. (13 x 76 mm) steel to suit your table (length ours). Drill a row of 5/8 in. (16 mm) holes 7/8 in. (22 mm) apart along its middle.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ដែកបន្ទះរាបថែបទន់ដែកបន្ទះរាបថែបទន់1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

រណារកាត់ដែករណារកាត់ដែក
ដែកគូសចំណុចកណ្តាលដែកគូសចំណុចកណ្តាល
ម៉ាស៊ីនចោះឈរម៉ាស៊ីនចោះឈរ
សំណុំក្បាលខួងសំណុំក្បាលខួង
4

Make the end supports

Cut two short pieces of the same stock, slot them for bolts to the drill-press table and fix one under each end of the bed (ours: bolted), so the bed stands clear of the table.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ដែកបន្ទះរាបថែបទន់ដែកបន្ទះរាបថែបទន់1 ដុំ
ការប្រមូលផ្ដុំប៊ូឡុងប្រាំមួយជ្រុងការប្រមូលផ្ដុំប៊ូឡុងប្រាំមួយជ្រុង1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

រណារកាត់ដែករណារកាត់ដែក
ម៉ាស៊ីនចោះឈរម៉ាស៊ីនចោះឈរ
សំណុំក្បាលខួងសំណុំក្បាលខួង
ដែកឆាប (ដែកឆាបដៃ)ដែកឆាប (ដែកឆាបដៃ)
5

Make the fixed jaw

Cut out a steel block underneath so it straddles the bed (stock and size ours). Drive a pin into it, downward, that fits the 5/8 in. holes.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ដែកបន្ទះរាបថែបទន់ដែកបន្ទះរាបថែបទន់1 ដុំ
ដែកទន់ដុំមូលដែកទន់ដុំមូល1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

រណារកាត់ដែករណារកាត់ដែក
ដែកឆាប (ដែកឆាបដៃ)ដែកឆាប (ដែកឆាបដៃ)
ម៉ាស៊ីនចោះឈរម៉ាស៊ីនចោះឈរ
សំណុំក្បាលខួងសំណុំក្បាលខួង
ញញួរក្បាលមូលញញួរក្បាលមូល
6

Make the sliding jaw

Cut a second block the same way. Pass a horizontal pin across the opening below the bed and rivet it to the jaw's sides, so the jaw slides along the bar but cannot lift off.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ដែកបន្ទះរាបថែបទន់ដែកបន្ទះរាបថែបទន់1 ដុំ
ដែកទន់ដុំមូលដែកទន់ដុំមូល1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

រណារកាត់ដែករណារកាត់ដែក
ដែកឆាប (ដែកឆាបដៃ)ដែកឆាប (ដែកឆាបដៃ)
ម៉ាស៊ីនចោះឈរម៉ាស៊ីនចោះឈរ
សំណុំក្បាលខួងសំណុំក្បាលខួង
ញញួរក្បាលមូលញញួរក្បាលមូល
ដង្កាប់តុដង្កាប់តុ
7

Make the cam

Saw a disk off steel shafting. Drive a pin that fits the 5/8 in. holes into one face, off centre. At right angles to it, drill a hole in the rim and fit a handle.

សម្ភារៈសម្រាប់ជំហាននេះ៖

អ័ក្សដែកថែបអ័ក្សដែកថែប1 ដុំ
ដែកទន់ដុំមូលដែកទន់ដុំមូល1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

រណារកាត់ដែករណារកាត់ដែក
ម៉ាស៊ីនចោះឈរម៉ាស៊ីនចោះឈរ
សំណុំក្បាលខួងសំណុំក្បាលខួង
ញញួរក្បាលមូលញញួរក្បាលមូល
8

Use it

Bolt the bed to the table. Set the fixed jaw's pin in the hole that suits the work, slide the jaw up, drop the cam pin into the hole behind it and swing the handle to lock the work.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ការប្រមូលផ្ដុំប៊ូឡុងប្រាំមួយជ្រុងការប្រមូលផ្ដុំប៊ូឡុងប្រាំមួយជ្រុង1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

ម៉ាស៊ីនចោះឈរម៉ាស៊ីនចោះឈរ
9

Troubleshooting

Drill vise troubleshooting.

Flow

Loading...
10

History and honest limits

From C. H. Willey, "A Simple Drill Vise", **Popular Mechanics** vol. 34 (November 1920), p. 3340 (checked on the archive.org scan of Popular Mechanics Shop Notes, popularmechanic00unkngoog). He gives only the bed section and the hole size and spacing; jaw and cam sizes, the bar length, how the end pieces are fixed and the cam offset are ours.

សម្ភារៈ

4

ឧបករណ៍ចាំបាច់

7

ប្លង់ពាក់ព័ន្ធ

ប្លង់ទាំងនេះចែករំលែកចំណេះដឹង — បច្ចេកទេស សម្ភារៈ ឬគោលការណ៍

CC0 សាធារណៈ

ប្លង់នេះត្រូវបានចេញផ្សាយក្រោម CC0។ អ្នកមានសិទ្ធិចម្លង កែប្រែ ចែកចាយ និងប្រើប្រាស់ដោយមិនចាំបាច់សុំអនុញ្ញាត។

គាំទ្រអ្នកបង្កើតដោយទិញផលិតផលតាមរយៈប្លង់របស់ពួកគេ ដែលពួកគេទទួលបាន កម្រៃជើងសារអ្នកបង្កើត កំណត់ដោយអ្នកលក់ ឬបង្កើតកំណែថ្មីនៃប្លង់នេះ ហើយបញ្ចូលជាការតភ្ជាប់ក្នុងប្លង់របស់អ្នកដើម្បីចែករំលែកចំណូល។

ការពិភាក្សា

(0)

ចូល ដើម្បីចូលរួមពិភាក្សា

កំពុងផ្ទុកមតិ...