
Echo Sounding and Sonar
안내
Measure the speed of sound in water yourself
Measure the speed of sound in water yourself
Establish the number the whole instrument depends on, in a tank.
- Put two hydrophones — or two waterproofed piezo elements — a measured distance apart in a long tank or a still pool.
- Make a sharp click at one end and record both channels simultaneously on an oscilloscope.
- Measure the delay between the two arrivals and divide the separation by it.
- Repeat with the water warmed by several degrees.
You should land near 1480 m/s in fresh water at room temperature — about 4.4 times the speed in air — and it will measurably INCREASE as the water warms. Roughly 4 m/s per degree, which sounds small until you remember it is multiplied by every range you compute.
Do the comparison honestly: sound in air is around 343 m/s and attenuates quickly; in seawater it travels for kilometres. That single contrast is why the sea is navigated acoustically and the sky is navigated electromagnetically, and why the two instruments look similar and behave completely differently.이 단계의 재료:
Piezo Transducer Element2 개
Clear Vinyl Tubing (10mm)1 m필요한 도구:
Oscilloscope 2-Channel 100MHz
Tape Measure (5 m)
Infrared Thermometer
Soldering Station (Temperature Controlled)The ping-listen cycle
The ping-listen cycle
Trace both. Active sonar gives you range immediately and tells the target exactly where you are — the ping is heard much further away than its own echo returns, so the hunted hears the hunter first.
Passive sonar is silent and gives bearing only. Converting bearings into a range requires the listener to manoeuvre and watch how the bearing changes over time — target motion analysis — which takes minutes and careful geometry.
Note the blind period after transmit. The transducer is a mechanical resonator and it keeps ringing after the drive stops, deafening the receiver — the acoustic version of the radar TR cell recovery time, and it sets the same minimum range.
This is why submarines run passive by default and go active only when they have already decided to attack or have been detected anyway. The instrument that answers the question fastest is also the one that gives you away.Flow
필요한 도구:
Desktop ComputerCompute range, resolution and the ray bending
Compute range, resolution and the ray bending
필요한 도구:
Desktop ComputerBuild a working echo sounder
Build a working echo sounder
Upload this and test in air first with SOUND_SPEED = 343.0 against a wall at a measured distance — if the reported range is wrong by a constant factor, your sound speed is wrong; if it is wrong by a constant offset, your blanking window is.
Then set 1500 m/s and test in water. The same code, the same arithmetic, a different constant — which is precisely the point the first step made.
The median-of-three is deliberate: a single ping can catch a bubble or a fish and report nonsense, and a median discards one outlier without the lag of a long average.
이 단계의 재료:
Piezo Transducer Element2 개
Microcontroller Board1 개
Transistor Assortment (NPN/PNP)1 키트
Resistor Kit1 키트
Capacitor Kit1 키트필요한 도구:
Computer with Arduino IDE
Oscilloscope 2-Channel 100MHz
Soldering Station (Temperature Controlled)
Digital Multimeter (Lab Grade)
Tape Measure (5 m)Read the bottom, and read what is under it
Read the bottom, and read what is under it
An echo sounder does not only find the seabed. It finds what the seabed is made of, and sometimes what is beneath it.
- Sound over mud, then over sand, then over rock, recording the returned envelope each time.
- Compare the amplitude and the SHAPE of each return.
- Look for a second, later echo after the first.
A hard bottom returns a sharp, strong echo; soft mud returns a weak, smeared one — because much of the sound enters the sediment instead of reflecting. That difference is enough to classify the seabed acoustically, which is how fishing grounds and cable routes are surveyed.
The second echo is the sound that went INTO the sediment, bounced off a harder layer below, and came back. Lower the frequency deliberately and that sub-bottom return strengthens — which is sub-bottom profiling, and it maps buried structure without digging.
The same instrument at three frequencies answers three different questions: high for fine detail of the bottom surface, medium for depth, low for what lies beneath it. This is the frequency-against-range trade from the notebook, used deliberately rather than merely suffered.이 단계의 재료:
Piezo Transducer Element1 개필요한 도구:
Oscilloscope 2-Channel 100MHz
Spectrum Analyser / FFT Software
Digital Multimeter (Lab Grade)재료
7- 플레이스홀더
- 플레이스홀더
- 1 tube플레이스홀더
- 플레이스홀더
- 플레이스홀더
- 1 키트플레이스홀더
- 1 키트플레이스홀더
필요 도구
8- 플레이스홀더
- 플레이스홀더
- 플레이스홀더
관련 블루프린트
이 블루프린트들은 지식을 공유합니다 — 기술, 재료 또는 원리
CC0 퍼블릭 도메인
이 블루프린트는 CC0로 공개되었습니다. 어떤 목적으로든 자유롭게 복사, 수정, 배포 및 사용할 수 있습니다.
제품 구매를 통해 메이커를 지원하세요. 판매자가 설정한 메이커 커미션 을 받거나, 이 블루프린트의 새로운 반복을 만들어 연결로 포함시킬 수 있습니다.


