예술
뷰티 및 웰니스
공예
문화 및 역사
엔터테인먼트
환경
음식 및 음료
역공학
과학
스포츠
기술
웨어러블
Piston-Pump Egg Beater: Pump the Eggs Through a Grate
A whisk stirs the eggs; it does not force them through anything.
J. J. Parker of Marietta, Ohio, received US 25,038, dated 9 August 1859, for an egg beater and churn combined: a tin tube with square openings at its lower end and a piston inside, worked up and down "in the manner of a pump" by a crank, which "draws the eggs in and out through the grate bars until they are completely torn in pieces or made perfectly fine and frothy"; a band turned round the tube's foot closes the openings to vary the agitation.
This rung works out the jet speed at each band setting, then prints the tube, band and piston, fits the crank, and times a beating at two settings.
중급
About 3 hours, plus printing
안내
1
1
Jet speed at each setting
Jet speed at each setting
Jupyter 노트북 불러오는 중…
2
2
The churning it also does
The churning it also does
The embedded blueprint churns cream to butter. Parker's pump-tube does the same when worked longer in cream.
3
3
Read US 25,038
Read US 25,038
"At the lower end of the tube is a band of about one half an inch in width loosely fitted with openings one fourth of an inch square and corresponding exactly with the openings in the tube and of the same size, so that by turning the band around either way the openings are closed or made smaller at pleasure, so as to produce more or less agitation in the eggs or cream. This band has a bottom with grate like bars cut or made in it."
4
4
Print the tube, band and piston
Print the tube, band and piston
Print the tube (/uploads/blueprints/piston-pump-egg-beater-tube.stl), the band with its grate (/uploads/blueprints/piston-pump-egg-beater-band.stl) and the piston disk (/uploads/blueprints/piston-pump-egg-beater-piston.stl). Print in PETG at 0.2 mm layers, 30 % infill, 4 walls.
이 단계의 재료:
PETG 필라멘트1 개필요한 도구:
FDM 3D 프린터5
5
Pack the piston
Pack the piston
Cut a leather disk 2 mm larger than the piston. Clamp it between the printed disk and a washer on an M3 rod end with a nut, so its edge seals the tube.
이 단계의 재료:
가죽1 개
평와셔1 개
육각 너트1 개
기계 나사1 개필요한 도구:
공예용 칼
멍키스패너
디지털 캘리퍼스 6인치6
6
Post and crank
Post and crank
Epoxy a 4 mm wire post up the tube's side, bent at its top into bearings 100 mm above the tube. Bend a crank shaft of 3 mm wire with a 22 mm crank one end and a handle the other, and link the crank to the rod with a wire pitman.
이 단계의 재료:
연강 환봉1 개
스테인리스 와이어1 개
2액형 에폭시1 개필요한 도구:
바이스(만력)
둥근 코 펜치
평집게
쇠톱(핵소)
투명 보안경7
7
The patent drawing
The patent drawing
US 25,038 drawing sheet, public domain (expired patent).
8
8
Beat at two settings
Beat at two settings
Stand the beater in a bowl with two eggs and a spoon of sugar. Crank twice a second with the band fully open and time to a fine froth; repeat with the band half closed.
이 단계의 재료:
달걀4 개
그래뉴당1 개필요한 도구:
큰 스테인리스강 믹싱볼
스톱워치9
9
A pump that leaks past, sticks or splashes
A pump that leaks past, sticks or splashes
Piston-pump egg beater troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**J. J. Parker** of Marietta, Ohio, received US 25,038, dated 9 August 1859. His smaller machine's tube is one and a half inches across and one and five eighths deep; the crank shaft is No. 7 wire with a seven-eighths-inch crank; the piston is two oval pieces of thin metal with leather between, its edges forced out by pressing them together. It may also be worked by a handle on the rod instead of a crank.
**Honest limits.** FDM prints hold food in their layer lines, so wash well and replace when worn. Printed PETG stands in for tin. The notebook treats the flow as steady. Your times are the result.
재료
10- 1 개플레이스홀더
- 1 개플레이스홀더
- 1 개플레이스홀더
- 1 개플레이스홀더
- 1 개플레이스홀더
- 1 개플레이스홀더
- 1 개플레이스홀더
- 1 개플레이스홀더
- 4 개플레이스홀더
- 1 개플레이스홀더
이 블루프린트로 만드는 것
관련 블루프린트
이 블루프린트들은 지식을 공유합니다 — 기술, 재료 또는 원리
CC0 퍼블릭 도메인
이 블루프린트는 CC0로 공개되었습니다. 어떤 목적으로든 자유롭게 복사, 수정, 배포 및 사용할 수 있습니다.
제품 구매를 통해 메이커를 지원하세요. 판매자가 설정한 메이커 커미션 을 받거나, 이 블루프린트의 새로운 반복을 만들어 연결로 포함시킬 수 있습니다.