예술
뷰티 및 웰니스
공예
문화 및 역사
엔터테인먼트
환경
음식 및 음료
역공학
과학
스포츠
기술
웨어러블
The Cam-Lever Lemon Squeezer: A Cam on a Shaft Presses the Plunger, Springs Lift It
Martin

작성자

Martin

30. 9월 2026NO
39
0
0
0
0

The Cam-Lever Lemon Squeezer: A Cam on a Shaft Presses the Plunger, Springs Lift It

A plunger pressed straight down by the hand needs a strong push to empty a lemon. A. Clarence Weeks of New York received US 165,638, dated 13 July 1875, for a squeezer with a frame on legs over a dish, a perforated bowl in the frame, a plate hinged to one end carrying the plunger, two standards on the frame with a shaft across them carrying "a cam-lever, G, arranged for contact of its face or bearing-surface with the upper side of the board or plate, which carries the plunger", and springs from the plate to the standards. "By the use of the cam-lever an immense power is obtained, and the juice is extracted from the lemon in a more thorough and perfect manner than when the power is applied directly to the plate or bar carrying the plunger." This rung works out the cam's average force, with a work check, then builds the frame, the hinged plate and the cam lever in hardwood and steel, and squeezes lemons with it.
중급
About 5 hours

안내

1

The cam's force

Jupyter 노트북 불러오는 중…
2

A lever press before it

The embedded blueprint presses the lemon with the lever itself. Weeks puts a cam lever over a hinged plate, so a turn of the lever gives a far greater push.
3

Read US 165,638

"Two standards, E E, are attached to the frame A, one on each side, in the upper portions of which standards are bearings for a shaft, f, to which is attached, midway of its length, a cam-lever, G, arranged for contact of its face or bearing-surface with the upper side of the board or plate, which carries the plunger. J is a spring, which may be of rubber or metal, having its lower end attached to the board or plate C, and its upper end attached to the standard E." "When the cam-lever G is depressed its face or bearing-surface presses upon the board or plate C, and forces the plunger into the bowl upon the lemon."
4

Build the squeezer and press lemons

**Frame and bowl.** Make a hardwood board frame on four legs, tall enough for a dish beneath, with a hole in it. Fit a tin-can bowl with a punched base into the hole. **Plate and plunger.** Hinge a hardwood plate to one end of the frame with a butt hinge, and screw a hardwood plunger to its underside so it enters the bowl. **Standards and cam.** Screw two hardwood standards to the frame's sides beside the plate and run a steel rod across between them as the shaft f. Cut a hardwood cam lever with a curved face whose distance from the shaft grows by about 15 mm over 60° of turn, drill it for the shaft, and fix it in the middle of the rod with a pin. **Springs.** Hook two extension springs from the plate to the standards so they lift the plate when the cam is raised. **Test.** Put a half lemon in the bowl over a dish and press the lever down. Compare the juice with a half pressed by pushing the plate down by hand.

이 단계의 재료:

경목 판재경목 판재2 개
경목 블록경목 블록2 개
나무 다월나무 다월0.6 미터
나사못나사못16 개
목공용 접착제목공용 접착제1 개
양철통양철통1 개
문 경첩문 경첩1 개
연강 환봉연강 환봉0.2 미터
못못2 개
인장 스프링인장 스프링2 개
레몬레몬3 개

필요한 도구:

손톱(핸드소)손톱(핸드소)
목공 끌 세트목공 끌 세트
거친 줄거친 줄
무선 드릴무선 드릴
드릴 비트 세트드릴 비트 세트
판금 가위판금 가위
망치망치
드라이버 세트드라이버 세트
쇠톱(핵소)쇠톱(핵소)
부엌칼부엌칼
디지털 주방 저울디지털 주방 저울
가죽 작업 장갑가죽 작업 장갑
5

A cam that slips, jams or does not lift

Cam-lever lemon squeezer troubleshooting.

Flow

Loading...
6

History and honest limits

**A. Clarence Weeks** of New York, New York, filed US 165,638 on 26 April 1875; it is dated 13 July 1875. His frame A had feet or legs a, the bowl B had perforations b, the plate C was hinged to one end of the frame, and there could be one spring or two. His claim is the frame with the perforated bowl and standards, the pivoted plate with its plunger, the springs, and the shaft with its cam lever. **Honest limits.** Hardwood, a tin bowl and a steel rod stand in for his parts. The notebook gives the average force without friction; its forces, lengths and angles are examples. Your juice is the result.

재료

11
  • 플레이스홀더
  • 플레이스홀더
  • 0.6 미터
    플레이스홀더
  • 16 개
    플레이스홀더
  • 플레이스홀더
  • 플레이스홀더
  • 플레이스홀더
  • 0.2 미터
    플레이스홀더
  • 2 개
    플레이스홀더
  • 플레이스홀더
  • 3 개
    플레이스홀더

필요 도구

12

이 블루프린트로 만드는 것

CC0 퍼블릭 도메인

이 블루프린트는 CC0로 공개되었습니다. 어떤 목적으로든 자유롭게 복사, 수정, 배포 및 사용할 수 있습니다.

제품 구매를 통해 메이커를 지원하세요. 판매자가 설정한 메이커 커미션 을 받거나, 이 블루프린트의 새로운 반복을 만들어 연결로 포함시킬 수 있습니다.

토론

(0)

로그인 하여 토론에 참여하세요

댓글 로딩 중...