예술
뷰티 및 웰니스
공예
문화 및 역사
엔터테인먼트
환경
음식 및 음료
역공학
과학
스포츠
기술
웨어러블
The Dough Kneader and Roller: Corrugated Rolls, Then Plain Ones
TheChef

작성자

TheChef

27. 9월 2026DK
9
0
0
0
0

The Dough Kneader and Roller: Corrugated Rolls, Then Plain Ones

Kneading dough by hand is hard, slow work, and the dough on an open table collects whatever is in the air. Judy W. Reed of Washington, D.C., filed US 305,474 on 21 January 1884; it is dated 23 September 1884, and its drawing sheet is titled "Dough Kneader and Roller". A closed box holds a pair of intermeshing corrugated metal rolls, one set by screws pressing on rubber plates so the squeeze can be increased or reduced, and below them a pair of plain rollers driven by a belt. Dough is put into a covered hopper, cranked through both pairs, and drops into a closed receptacle with a door — kneaded, rolled, and kept from dust throughout. This rung works out when rollers grip the dough and how much sheet a crank turn makes, and builds a two-roller model.
중급
About 3 hours

안내

1

The nip condition and the sheet

Jupyter 노트북 불러오는 중…
2

Two rollers and a spring

A wringer squeezes cloth between rollers pressed together by a spring. The embedded blueprint shows the same arrangement Reed used for dough.
3

Read US 305,474

Reed's objects are, first, "to subject the mass of dough to a thorough and equable mixing and working by causing it to pass between a pair of intermeshing corrugated rollers or cylinders", which approach or recede by regulating-screws "according as the pressure on the dough is desired to be increased or diminished, and then passing it between a pair of plain rollers to roll the dough"; second, a covered receiver and a receptacle for the dough; and third, "to protect the mass of dough from dust or impurities in the atmosphere throughout its working". In the case A A′ are corrugated metallic rolls B B′ and plain rollers G G′; B′ carries a crank. Roll B runs in movable bearings c′ pressed by screws C that bear on rubber plates f, keeping it against B′. The plain roller G hangs from B's bearings and is driven by a belt from B's axle. The upper part A′ has a hopper-shaped receiver D, "preferably lined with tin or other thin metal to prevent any taste of the wood", hinged so it can be swung back to remove the rolls for cleaning; below is a receptacle E with a door F.
4

Build a two-roller model

Mount two hardwood dowels about 30 mm thick in a plywood frame, one in fixed holes and one in slots, with wing nuts or screws to set the gap. Wrap one dowel's surface with evenly spaced ribs of more dowel glued lengthwise, to stand for corrugations, and fit a crank to the fixed one. Mix a simple bread dough with flour and water. Feed a lump through with the ribbed roll, then with both rolls smooth, starting with a wide gap and narrowing it pass by pass. Note the thickest lump each set-up will draw in and compare with the notebook. Finish the sheet with a rolling pin and measure its thickness with the caliper.

이 단계의 재료:

다목적 밀가루다목적 밀가루1 개
단단한 나무 목심단단한 나무 목심1 개
합판합판1 개
나사못나사못8 개

필요한 도구:

밀대밀대
무선 드릴무선 드릴
드릴 비트 세트드릴 비트 세트
디지털 캘리퍼스 6인치디지털 캘리퍼스 6인치
디지털 주방 저울디지털 주방 저울
글루건글루건
5

Rollers that will not take the dough

Dough roller troubleshooting.

Flow

Loading...
6

History and honest limits

**Judy W. Reed** of Washington, D.C., filed US 305,474 on 21 January 1884; it is dated 23 September 1884. It claims the case with its corrugated rolls, one movable and one cranked, the belt-driven plain rollers, and the hopper above and receptacle below. **Honest limits.** The friction coefficients in the notebook are assumptions; dough's grip varies with its water, flour and rest.

재료

4

필요 도구

6

CC0 퍼블릭 도메인

이 블루프린트는 CC0로 공개되었습니다. 어떤 목적으로든 자유롭게 복사, 수정, 배포 및 사용할 수 있습니다.

제품 구매를 통해 메이커를 지원하세요. 판매자가 설정한 메이커 커미션 을 받거나, 이 블루프린트의 새로운 반복을 만들어 연결로 포함시킬 수 있습니다.

토론

(0)

로그인 하여 토론에 참여하세요

댓글 로딩 중...