예술
뷰티 및 웰니스
공예
문화 및 역사
엔터테인먼트
환경
음식 및 음료
역공학
과학
스포츠
기술
웨어러블
The Spring Bottle Stopper: Let the Pressure Seal It
A cork in a soda bottle has to be driven hard, wired down, and pulled with a corkscrew, and the pressure inside is always trying to push it out.
Charles G. Hutchinson of Chicago received US 213,992, dated 8 April 1879 (filed 28 October 1878), for a stopper that sits INSIDE the neck: a rubber disc on a wire bent "to approximate the figure 8 in form", pulled up into the narrow neck to close the bottle and pushed down to open it. The gas pressure inside then holds it shut.
This rung works out the force the pressure puts on the stopper, then makes an inside stopper for a bottle and tests its seal.
초급
About 2 hours
안내
1
1
The force that holds the stopper shut
The force that holds the stopper shut
Jupyter 노트북 불러오는 중…
2
2
Where the pressure comes from
Where the pressure comes from
The embedded blueprint carbonates drinks in the bottle and warns about too much pressure. Hutchinson's stopper turns that pressure into the seal.
3
3
Read US 213,992
Read US 213,992
"In order that the stopper B may be suspended below or away from the neck of the bottle, I extend the spring C upward, and make this upper part sufficiently large to prevent it from falling down through the neck, but not so large as to prevent the lower part of the spring from passing through or below the narrowest part of the neck."
"A simple and inexpensive way of constructing a spring for the purposes set forth, and uniting in it all the advantages now recited, is to make it of flexible wire, bending the wire so that the spring will approximate the figure 8 in form".
4
4
Make an inside stopper and test the seal
Make an inside stopper and test the seal
Cut a rubber disc a little wider than the narrowest part of a bottle's neck. Bend steel wire into a figure 8, with the lower loop fixed to the disc and the upper loop too wide to fall through the neck.
Push the disc into the bottle, fill it with carbonated water, turn it upside down briefly so the disc falls into the neck, and pull it up by the wire loop to seal. Leave it for a day and see whether the fizz is kept. Measure the pressure of a sealed bottle with the gauge where you can fit one, and compare with the notebook.
이 단계의 재료:
고무 시트1 개
강철선1 개
탄산수(개봉하지 않은 병)1 개필요한 도구:
병마개
스윙톱 유리병
롱노즈 플라이어
압력계
가위5
5
A stopper that leaks, sticks or falls in
A stopper that leaks, sticks or falls in
Inside stopper troubleshooting.
Flow
Loading...
6
6
History and honest limits
History and honest limits
**Charles G. Hutchinson** of Chicago, Cook County, Illinois, filed US 213,992 on 28 October 1878; it is dated 8 April 1879. The stopper can be pulled up with a small hook through the top of the wire loop.
**Honest limits.** The notebook treats the pressure as acting on the whole disc and ignores the rubber's own grip. The pressures and disc sizes are examples. Your sealed bottle is the measurement.
관련 블루프린트
이 블루프린트들은 지식을 공유합니다 — 기술, 재료 또는 원리
CC0 퍼블릭 도메인
이 블루프린트는 CC0로 공개되었습니다. 어떤 목적으로든 자유롭게 복사, 수정, 배포 및 사용할 수 있습니다.
제품 구매를 통해 메이커를 지원하세요. 판매자가 설정한 메이커 커미션 을 받거나, 이 블루프린트의 새로운 반복을 만들어 연결로 포함시킬 수 있습니다.