ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Air Compressor: Twin Pump-Cylinder, Water-Cooled (Shop Notes, 1912)
Emma

สร้างโดย

Emma

4. พฤศจิกายน 2026SE
12
0
0
0
0

Air Compressor: Twin Pump-Cylinder, Water-Cooled (Shop Notes, 1912)

A simple compressor that fills a tank to about 50 lb: two bought cast-iron well-pump cylinders, 2 1/2 in bore, driven alternately by a rocking arm from a crank, with check valves in and out and a water jacket pipe to cool them. Source: Popular Mechanics Shop Notes for 1912, pp. 1708-1709. Unknown: tank, pipe sizes. Picture: Figs. 1-2 of the book.
ระดับกลาง
Unknown

คำแนะนำ

1

Pipe the two cylinders

Take two ordinary cast-iron open-well pump cylinders, 2 1/2 in bore, bought complete with guide rods and plungers. Join their open ends with tees to a cross pipe C, and fit a packing box from an old valve (A, B) into each tee so the plunger rods D and E pass through (Fig. 1).

วัสดุสำหรับขั้นตอนนี้:

โลหะที่ไม่ทราบโลหะที่ไม่ทราบ2 pump cylinders with plungers
ท่อเหล็ก (ผนังหนา ปลายเกลียว)ท่อเหล็ก (ผนังหนา ปลายเกลียว)1 pipe C
ข้อต่อท่อเกลียวข้อต่อท่อเกลียว2 tees
วัสดุอัดกันรั่วที่ไม่ทราบวัสดุอัดกันรั่วที่ไม่ทราบ2 packing boxes

เครื่องมือที่ต้องใช้:

ประแจจับท่อประแจจับท่อ
2

Fit the valves

On the outer end of each cylinder fit an inlet check valve (H, I) and an outlet valve (J, K), the outlets joined to pipe L running to the tank.

วัสดุสำหรับขั้นตอนนี้:

วาล์วกันกลับวาล์วกันกลับ4 H, I, J, K
ท่อเหล็ก (ผนังหนา ปลายเกลียว)ท่อเหล็ก (ผนังหนา ปลายเกลียว)1 pipe L
ข้อต่อท่อเกลียวข้อต่อท่อเกลียว1 ชิ้น
วัสดุที่ไม่ทราบวัสดุที่ไม่ทราบ1 air tank

เครื่องมือที่ต้องใช้:

ประแจจับท่อประแจจับท่อ
3

Water-cool it

Run cooling water through pipe C, set by valve M in and valve N out, so there is no pressure on the water to push it into the air chambers O and P.

วัสดุสำหรับขั้นตอนนี้:

วาล์วโกลบวาล์วโกลบ2 M and N

เครื่องมือที่ต้องใช้:

น้ำน้ำ
ประแจจับท่อประแจจับท่อ
4

Fit the crank drive

Drive it from a shaft (Fig. 2): crank S works an arm pivoted at its centre T, and the plunger rods D and E attach to the arm's ends U and V.

วัสดุสำหรับขั้นตอนนี้:

โลหะที่ไม่ทราบโลหะที่ไม่ทราบ1 crank, arm
สลักเกลียวหัวหกเหลี่ยม - เกรด 8.8สลักเกลียวหัวหกเหลี่ยม - เกรด 8.81 pivot and rod pins, number not given

เครื่องมือที่ต้องใช้:

สว่านมือสว่านมือ
ประแจเลื่อนประแจเลื่อน

วัสดุ

8

เครื่องมือที่จำเป็น

4
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง
  • ตัวยึดตำแหน่ง

พิมพ์เขียวนี้สร้าง

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...