ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Twin Inclined-Wing Dasher Churn: Two Geared Dashers With Up- and Down-Sloping Wings Turn Through Each Other, Flat Wings Between
Levi Bissell of North Bergen, New York, received US 29,052, dated 10 July 1860, for a churn with two upright dashers in an oblong body. A crank on a lift-off frame drives both through gears, the same way round, so their wings pass each other in opposite directions in the middle. Each dasher's wings slope up on one side and down on the other, and one dasher's down-sloping wings pass between the other's up-sloping ones, so the cream is driven up and down at once. Flat wings between them check the swirl.
The patent gives no sizes; every size here is ours.
ระดับกลาง
About 3 days
คำแนะนำ
1
1
Where the wings meet
Where the wings meet
กำลังโหลดสมุด Jupyter…
2
2
Two shafts turned the same way by one wheel, eight months before
Two shafts turned the same way by one wheel, eight months before
Cornell's two shafts also turn the same way off one wheel, lying flat. Bissell stands them upright and slopes the wings.
3
3
Read US 29,052
Read US 29,052
"Thus it will be seen that the downwardly inclined wings move in paths describing broad cones, pointing upward; while the upwardly inclined wings describe cones pointing downward; and as these rapidly alternate, they cut paths through the milk or cream rapidly crossing each other, thereby producing intense and effective agitation of the cream."
4
4
Body A and sockets a
Body A and sockets a
Draw two 330 mm circles, centres 220 mm apart, joined by straight lines, on 20 mm hardwood glued up wide enough, and cut the floor to it. Rout a groove 1.6 mm wide and 8 mm deep on the 290 mm circles and their joining lines. Cut two strips of 1.5 mm stainless sheet 428 mm high, bend them to the outline, stand them in the groove with silicone sealant, and lap and rivet the joins on the straight sides with sealant between. Glue up a hardwood rim 18 mm thick and 30 mm deep to fit round the top, screwed through the sheet. Screw a hardwood block 60 x 64 x 70 mm to the middle of each long side, 150 mm up, with a 24 mm square socket a down through it, sealing the screw holes.
วัสดุสำหรับขั้นตอนนี้:
แผ่นไม้เนื้อแข็ง3 ชิ้น
แผ่นสเตนเลส2 ชิ้น
หมุดย้ำแบบดึง12 ชิ้น
กาวไม้1 ชิ้น
สกรูไม้24 ชิ้นเครื่องมือที่ต้องใช้:
เข็มทิศ
เลื่อยจิ๊กซอว์
เราเตอร์
ชุดสิ่วไม้
กรรไกรตัดแผ่นโลหะ
ชุดปืนย้ำหมุด
สว่านไร้สาย
ชุดดอกสว่าน
แคลมป์แบบบาร์
ชุดไขควง5
5
Dashers I with wings L and M
Dashers I with wings L and M
Cut two hardwood shafts 28 mm round and 408 mm long; turn the foot of each to 16 mm for 18 mm, and set a 16 mm stainless rod 103 mm long 40 mm into the top, pinned. Cut eight hardwood wings L 250 x 25 x 8 mm and six flat wings M 114 x 24 x 8 mm. Chisel slots through each shaft and drive the wings through, each pinned with a small dowel: the L pairs sloping 20 degrees, all in one plane, at 60, 140, 220 and 300 mm above the floor on one shaft and 100, 180, 260 and 340 mm on the other; the M wings flat, at right angles to the L, midway between them. Screw two hardwood steps 40 mm across, each with a 16.6 mm hole 6 mm deep, to the floor at the two end centres.
วัสดุสำหรับขั้นตอนนี้:
แผ่นไม้เนื้อแข็ง1 ชิ้น
แท่งสเตนเลส1 ชิ้น
เดือยไม้เนื้อแข็ง1 ชิ้น
กาวไม้1 ชิ้น
สกรูไม้4 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยวงเดือนตั้งโต๊ะ
ชุดสิ่วไม้
สว่านไร้สาย
ชุดดอกสว่าน
เลื่อยตัดเหล็ก
ตะไบ (ตะไบมือ)
ปากกาจับชิ้นงานหน้าโต๊ะ6
6
Print the cog-wheel G
Print the cog-wheel G
The cog-wheel G on the upright shaft: 40 teeth, module 2.75, 12 mm thick, 12.4 mm bore. PETG, 0.2 mm layers, 30 % infill, 4 walls.
7
7
Print the pinions H (two)
Print the pinions H (two)
The two pinions H on the dasher shafts, the same size as G: 40 teeth, module 2.75, 16.4 mm bore. Print two. PETG, 0.2 mm layers, 30 % infill, 4 walls.
8
8
Print the crown wheel D
Print the crown wheel D
The driving wheel D on the crank shaft, a crown wheel of 36 teeth, module 2, 12.4 mm bore. PETG, 0.2 mm layers, 30 % infill, 4 walls.
9
9
Print the pinion E
Print the pinion E
The pinion E on the upright shaft, 12 teeth, module 2, 12.4 mm bore, meshing the crown wheel D. PETG, 0.2 mm layers, 30 % infill, 4 walls.
10
10
Frame B, cover, gearing and winch C
Frame B, cover, gearing and winch C
Cut a hardwood board 340 x 396 x 25 mm and screw two 22 mm square hardwood standards 302 mm long under the middle of its 340 mm edges to drop into the sockets a. Bore it 16.8 mm over the two dasher shafts and 12.8 mm at the centre. Cut a 12 mm HDPE cover to the body's outside outline with 28 mm holes over the dashers. Stand the dashers in their steps, put on the cover and drop the frame into the sockets. Pin a pinion H on each dasher rod above the board with both wing planes lying along the churn, one dasher's down-sloping wings toward the other's up-sloping ones. Run a 12 mm stainless upright shaft 113 mm long through the centre hole with the wheel G pinned on it meshing both pinions, and the pinion E pinned 60 mm above the board. Screw two hardwood chairs 44 x 30 x 116 mm to the board, bored 12.6 mm across, carry a 12 mm stainless crank shaft in them with the crown wheel D pinned on its end meshing E, and hold it with shaft collars. Pin on a crank C of mild steel flat bar, 88 mm throw, with a hardwood handle.
วัสดุสำหรับขั้นตอนนี้:
แผ่นไม้เนื้อแข็ง1 ชิ้น
แผ่น HDPE1 ชิ้น
แท่งสเตนเลส1 ชิ้น
เหล็กแบนกล้าละมุน1 ชิ้น
Shaft Collar2 ชิ้น
สลักผ่า6 ชิ้น
เดือยไม้เนื้อแข็ง1 ชิ้น
สกรูไม้12 ชิ้น
กาวไม้1 ชิ้น
เส้นใย PETG1 ชิ้นเครื่องมือที่ต้องใช้:
เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)
เลื่อยวงเดือนตั้งโต๊ะ
เลื่อยจิ๊กซอว์
ชุดดอกสว่านใบพาย
สว่านไร้สาย
ชุดดอกสว่าน
เลื่อยตัดเหล็ก
ตะไบ (ตะไบมือ)
ปากกาจับชิ้นงานหน้าโต๊ะ
ชุดไขควง
ตลับเมตร11
11
The build in 3D
The build in 3D
FreeCAD model of this build, the body cut open: the floor, sheet wall and rim, the sockets and the lift-off frame, the winch, crown wheel and pinion, the cog-wheel and two pinions, and the two dashers with their sloping wings L and flat wings M passing between each other.
12
12
Churn
Churn
Pour about 25 litres of heavy cream at about 15 °C, checked with the thermometer, into the body, about half full; put on the cover and drop in the frame. Turn the winch steadily, timing it. When the butter comes, lift the frame out of its sockets, take off the cover and lift out the dashers. Take out the butter from the ends, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.
วัสดุสำหรับขั้นตอนนี้:
ครีมสด25 l
เกลือทะเลเม็ดหยาบ1 ชิ้น
น้ำ1 ชิ้นเครื่องมือที่ต้องใช้:
เทอร์มอมิเตอร์หัววัดแบบเสียบค้าง
นาฬิกาจับเวลา
เครื่องชั่งดิจิทัลสำหรับครัว
ชามผสมสเตนเลสใบใหญ่13
13
Troubleshooting
Troubleshooting
Twin-dasher churn troubleshooting.
Flow
Loading...
14
14
History and honest limits
History and honest limits
**Levi Bissell** of North Bergen, Genesee County, New York, US 29,052, 10 July 1860, "Churn". He claimed "the oppositely inclined sets of dasher wings L, L, following each other on their respective shafts, while those of one dasher alternate and intermatch with those of the other dasher, and the intermediate, horizontal dasher wings M, M". He did not claim two dashers with intermatching wings as such, nor sloping wings alone. He also allowed "feathering" the wings, in one way or in contrary ways; ours are not feathered. His gears were a bevel wheel and pinion; ours are a printed crown wheel and pinion. The patent gives no sizes; every size here is ours.
วัสดุ
16- 3 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 12 ชิ้นตัวยึดตำแหน่ง
- 3 ชิ้นตัวยึดตำแหน่ง
- 40 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 6 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 25 lตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
เครื่องมือที่จำเป็น
21- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
ไฟล์ออกแบบ
5พิมพ์เขียวนี้สร้าง
บลูพริ้นท์ที่เกี่ยวข้อง
บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

Double Rotary Crag Churn: Two Shafts of Four-Edged Arms Turn Through Each Other in Twin Half-Cylinders
โดย Buttercup
งานไม้
13
0
0
0
0
0

Twin-Crank Slide-Top Churn: Two Dashers on a Bent Crank Shaft, Sliding Plates Keep the Milk In
โดย Buttercup
งานไม้
10
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
โดย TheChef
งานฝีมือ
63
0
0
0
0
0
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

