ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Boring Bar: Driven Between Centres, with a Set-Screw Cutter (Yates, 1922)
Forge

สร้างโดย

Forge

4. พฤศจิกายน 2026NO
14
0
0
0
0

Boring Bar: Driven Between Centres, with a Set-Screw Cutter (Yates, 1922)

A home-made boring bar for holes too long for an ordinary boring tool, which would spring. A short, stiff bar runs between the lathe centres, driven by a dog, and carries a hardened tool-steel cutter locked in a cross-hole by a set screw. The work is bolted to the lathe carriage and fed past the turning cutter. Result: a boring bar, plus the small short-cut bar of Fig. 110. Source: R. F. Yates, Lathe Work for Beginners (1922), pp. 134-136. Unknown: bar diameter and set-screw size. Picture: Figs. 110-111 of the book.
ระดับกลาง
Unknown

คำแนะนำ

1

Turn the bar

Turn a bar no longer than the job needs; the shorter it is, the less it twists under the cut. Drill both ends for the lathe centres. For short cuts, the small bar of Fig. 110 is 4 to 6 inches long with a round shank and a squared end. Ours: mild steel round bar. Not given: the diameter.

วัสดุสำหรับขั้นตอนนี้:

เหล็กเส้นกลมเหล็กกล้าละมุนเหล็กเส้นกลมเหล็กกล้าละมุน1 boring bar

เครื่องมือที่ต้องใช้:

เครื่องกลึงโลหะเครื่องกลึงโลหะ
ขนาดที่ไม่ทราบขนาดที่ไม่ทราบ
2

Fit the cutter and set screw

Drill a cross-hole through the bar for the cutter and drill and tap a hole into it for a set screw that locks the cutter. Make the cutter of tool steel, grind its point with proper clearance, and harden it.

วัสดุสำหรับขั้นตอนนี้:

เหล็กเครื่องมือสี่เหลี่ยมจัตุรัสเหล็กเครื่องมือสี่เหลี่ยมจัตุรัส1 cutter
โลหะที่ไม่ทราบโลหะที่ไม่ทราบ1 set screw

เครื่องมือที่ต้องใช้:

สว่านแท่นสว่านแท่น
ชุดต๊าปและดายทำเกลียวชุดต๊าปและดายทำเกลียว
หินลับแบบหมุนหินลับแบบหมุน
เตาอบชุบความร้อนเตาอบชุบความร้อน
ถังชุบน้ำถังชุบน้ำ
3

Bore with it

Bolt the work down to the lathe carriage carefully and securely; carriage bolts of several sizes are handy for this. Drive the bar between centres with a dog and feed the carriage. Run very slowly when boring cast iron, and keep the feed light so the bar does not spring.

เครื่องมือที่ต้องใช้:

เครื่องกลึงโลหะเครื่องกลึงโลหะ
สลักเกลียวหัวกลมสลักเกลียวหัวกลม

วัสดุ

3

เครื่องมือที่จำเป็น

8

พิมพ์เขียวนี้สร้าง

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...