ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Clamp-On Countersink: Two Blocks Screwed Round Any Drill, Twin Cutters Countersink the Hole as It Is Bored (Brackin, 1903)
Forge

สร้างโดย

Forge

13. พฤศจิกายน 2026NO
14
0
0
0
0

Clamp-On Countersink: Two Blocks Screwed Round Any Drill, Twin Cutters Countersink the Hole as It Is Bored (Brackin, 1903)

George W. Brackin of Philadelphia received US 727,580, dated 12 May 1903, for a countersink that clamps onto a drill or auger bit. Two blocks are screwed together across the bit at any point along it. A twin cutter is screwed into an inclined seat in each block, its point reaching into the bit's flutes. As the bit bores, the cutters arrive and cut the cone for the screw head without taking the bit out. A slotted stop sets how deep it goes, so it gauges the hole too. We make three for 4, 5 and 6 mm drills. The patent gives no sizes; every size here is ours.
ระดับกลาง
About 1 day

คำแนะนำ

1

Setting it on the bit

กำลังโหลดสมุด Jupyter…
2

Read US 727,580

"From Figs. 2 and 3 it will be observed that the lower ends of the inclined cutters project slightly into the twists or helical channels of the drill, and this fact permits the cutters to enter the hole bored and then commence cutting away the edge of the hole as the tool is rotated."
3

Clamping blocks 2 and 3

For each attachment cut two blocks 40 x 12 x 10 mm from square bar. In each, 6 mm from one end drill a 4.5 mm plain hole and 6 mm from the other end drill 3.3 mm and tap M4, through the 12 mm face, so the two blocks screw together with the plain hole of one over the tapped hole of the other. Across the middle of each block's outer face file a seat 6 mm wide, sloping down and in at 45 degrees, and drill and tap M4 in it for the cutter's screw.

วัสดุสำหรับขั้นตอนนี้:

แท่งเหล็กกล้าละมุนหน้าตัดสี่เหลี่ยมแท่งเหล็กกล้าละมุนหน้าตัดสี่เหลี่ยม1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
เหล็กขีดเหล็กขีด
เหล็กตอกนำศูนย์เหล็กตอกนำศูนย์
สว่านแท่นสว่านแท่น
ชุดดอกสว่านชุดดอกสว่าน
ชุดต๊าปและดายทำเกลียวชุดต๊าปและดายทำเกลียว
ด้ามจับต๊าปเกลียวด้ามจับต๊าปเกลียว
ชุดตะไบชุดตะไบ
ไม้โปรแทรกเตอร์ไม้โปรแทรกเตอร์
เวอร์เนียร์ดิจิทัล 6 นิ้วเวอร์เนียร์ดิจิทัล 6 นิ้ว
4

Twin cutters 8 and 9

Cut four cutters 22 mm long from 3 x 6 mm carbon steel strip. Drill each 4.5 mm for its screw at the top, and grind the lower end to a point with a straight cutting edge 13 on its leading side and a rounded back 15, as his Fig. 4. Harden: heat to a cherry red, until a magnet no longer sticks, quench in water, rub bright, and draw to a light straw colour.

วัสดุสำหรับขั้นตอนนี้:

แถบเหล็กกล้าคาร์บอนแถบเหล็กกล้าคาร์บอน1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
สว่านแท่นสว่านแท่น
ชุดดอกสว่านชุดดอกสว่าน
เครื่องเจียรตั้งโต๊ะเครื่องเจียรตั้งโต๊ะ
เตาตีเหล็กเตาตีเหล็ก
คีมช่างตีเหล็กคีมช่างตีเหล็ก
แม่เหล็กเล็กแม่เหล็กเล็ก
ถังชุบน้ำถังชุบน้ำ
น้ำน้ำ
หินลับมีดหินลับมีด
ถุงมืองานเชื่อมถุงมืองานเชื่อม
แว่นนิรภัยแว่นนิรภัย
5

Stop 17 and assembly

Bend a strip of 3 mm flat bar into an L, its upright 30 mm long with a 4.5 mm slot 18 15 mm long, its foot 20 mm. Screw a cutter into each block's seat. Put the blocks either side of the drill, the stop's slot under one clamping screw, and screw them together until they grip the drill, the cutters' points just in the flutes and their edges leading as the drill turns.

วัสดุสำหรับขั้นตอนนี้:

เหล็กแบนกล้าละมุนเหล็กแบนกล้าละมุน1 ชิ้น
สกรูเกลียวมิลสกรูเกลียวมิล4 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
สว่านแท่นสว่านแท่น
ชุดดอกสว่านชุดดอกสว่าน
ชุดตะไบชุดตะไบ
ชุดไขควงชุดไขควง
6

Bore and countersink

Set the drill's point the hole's depth below the stop's foot and the cutters for the screw head's size (the notebook gives both). Drill into hardwood until the stop touches: the hole is at depth and its mouth countersunk. Check a screw sits flush.

เครื่องมือที่ต้องใช้:

สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง
เวอร์เนียร์ดิจิทัล 6 นิ้วเวอร์เนียร์ดิจิทัล 6 นิ้ว
แว่นนิรภัยแว่นนิรภัย
7

Troubleshooting

Clamp-on countersink troubleshooting.

Flow

Loading...
8

History and honest limits

**George W. Brackin** of Philadelphia, US 727,580, dated 12 May 1903, filed 18 June 1902. He claimed "the rectangular clamping-blocks arranged parallel to each other, clamping-screws passing through the said blocks near their ends", each block "provided exteriorly at its middle point with a cutter-seat inclined downwardly and inwardly", and "duplicate and interchangeable cutters" screwed into them. His was for wood, with the note that the cutters could be hardened for metal; ours are hardened. He gives no sizes or angle; every size here is ours.

วัสดุ

4

เครื่องมือที่จำเป็น

23

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...