ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Carbon Film Resistors: Methane Cracked on Ceramic Rods, Helixed and Varnished (Bell Labs 1951)
Ed

สร้างโดย

Ed

2. พฤศจิกายน 2026FI
13
0
0
0
0

Carbon Film Resistors: Methane Cracked on Ceramic Rods, Helixed and Varnished (Bell Labs 1951)

Ceramic rods tumble in a hot, gas-tight rotating furnace while methane cracks on them and leaves a thin, hard film of carbon. The coated rods get conducting ends, a helix ground through the film to bring them near their value, a light rub to the exact value, and a coat of baking varnish. Result: carbon film resistors adjusted to as close as ±0.5 %. The helix alone can raise a rod's resistance by any factor from about 10 to about 8000. Source: Grisdale, Pfister and van Roosbroeck, Pyrolytic Film Resistors, Bell System Technical Journal 30 (1951). Unknown: the ceramic of the rods, the end caps and leads, and which baking varnish; the paper does not give them. Picture: Wikimedia Commons.
ขั้นสูง
2 days

คำแนะนำ

1

Load the furnace

Load cylindrical ceramic rods into the gas-tight refractory core of a rotating (or rocking) batch furnace, with silica sand to support the rods and keep them from damage as they tumble. Unknown: which ceramic.

วัสดุสำหรับขั้นตอนนี้:

แกนฉนวนของตัวต้านทานแกนฉนวนของตัวต้านทาน1 batch

เครื่องมือที่ต้องใช้:

เตาหมุนแบบเป็นชุดเตาหมุนแบบเป็นชุด
ทรายควอตซ์ทรายควอตซ์
2

Heat under nitrogen

Turn the core and bring it to temperature, usually about 975 to 1300 °C, flushing it with nitrogen before any hydrocarbon goes in.

เครื่องมือที่ต้องใช้:

เตาหมุนแบบเป็นชุดเตาหมุนแบบเป็นชุด
ไนโตรเจนไนโตรเจน
3

Crack the methane

When the temperature is steady, let in the coating gas and keep it flowing for the time needed. The film grows at a steady rate: at 1000 °C and 30 % methane the paper runs from 0.2 to 10 hours. Longer gives a thicker film of lower resistance; temperature sets the rate more than anything else, and more methane deposits faster.

วัสดุสำหรับขั้นตอนนี้:

มีเทนมีเทน1 flow

เครื่องมือที่ต้องใช้:

เตาหมุนแบบเป็นชุดเตาหมุนแบบเป็นชุด
4

Cool under nitrogen

Shut off the methane and let the core cool while oxygen-free nitrogen keeps flowing. The films come out clean, even and firmly stuck.

เครื่องมือที่ต้องใช้:

เตาหมุนแบบเป็นชุดเตาหมุนแบบเป็นชุด
ไนโตรเจนไนโตรเจน
5

Terminate the ends

Paint the ends of each coated rod with a water suspension of colloidal graphite (Aquadag), then burnish and bake it; this suits all but low-value resistors. Fit the end caps with their leads. Unknown: the caps and leads, which the paper does not describe. Ours: an agate burnisher and an oven.

วัสดุสำหรับขั้นตอนนี้:

แกรไฟต์คอลลอยด์แกรไฟต์คอลลอยด์1 as required
ฝาปลายตัวต้านทานพร้อมขาฝาปลายตัวต้านทานพร้อมขา2 per resistor

เครื่องมือที่ต้องใช้:

เครื่องมือขัดหินอาเกตเครื่องมือขัดหินอาเกต
เตาอบเตาอบ
6

Grind the helix

Grind a helical groove through the film with a water-cooled, metal-bonded diamond wheel, the blank floating against the wheel so the groove stays even. Pick the pitch to land slightly below the wanted value (330 Ω, 10 kΩ or any other). The groove must be smooth: cracks into the carbon ribbon bring noise and drift.

เครื่องมือที่ต้องใช้:

เครื่องตัดเกลียวตัวต้านทานเครื่องตัดเกลียวตัวต้านทาน
7

Rub to value and varnish

Turn the resistor while measuring it continuously, and rub its whole surface lightly with a cotton pad wet with an organic solvent until it reaches its value. Leave it just below tolerance, then give it one or more coats of baking varnish, which raises the resistance by generally less than 1 %. Unknown: which varnish and its baking. Ours: acetone as the solvent, a Wheatstone bridge to measure.

วัสดุสำหรับขั้นตอนนี้:

วานิชอบวานิชอบ1 as required

เครื่องมือที่ต้องใช้:

วงจรบริดจ์วีตสโตนวงจรบริดจ์วีตสโตน
สำลีซับสำลีซับ
อะซิโตนอะซิโตน
เตาอบเตาอบ

วัสดุ

5

เครื่องมือที่จำเป็น

9

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...