ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Ceramic Disc Capacitors: Barium Titanate with Nickel Stannate, Pressed, Fired and Silvered (Coffeen, US 2,789,061)
Barium titanate with 3 mole % nickel stannate is calcined, pressed into small discs and fired hard. Silver is fired onto both faces and a lead soldered to each, giving ceramic disc capacitors of high capacity for their size.
Result: discs 3/8 inch across and about 1/10 inch thick with a dielectric constant averaging 2380 and a dissipation factor of 0.58 %. Between 25 and 85 °C the dielectric constant rose at most 17 % and fell at most 7 %.
Source: W. W. Coffeen (Metal & Thermit Corp.), US 2,789,061 (1957). Unknown: how the barium titanate, the nickel stannate and the tinned lead wire are made; the patent uses them ready-made. Picture: Wikimedia Commons.
ขั้นสูง
10 days
คำแนะนำ
1
1
Weigh and slurry
Weigh and slurry
Weigh 19.32 g of barium titanate and 0.68 g of hydrated nickel stannate (about NiSnO3·2H2O), which is 97 mole % BaTiO3 and 3 mole % NiSnO3. Slurry them with 50 cc of distilled water. The patent prefers 2 to 4 mole % nickel stannate; 1 to 15 % works.
วัสดุสำหรับขั้นตอนนี้:
แบเรียมไททาเนต19.32 ก.
นิกเกิลสแตนเนต0.68 ก.เครื่องมือที่ต้องใช้:
น้ำกลั่น
เครื่องชั่งดิจิทัลความแม่นยำสูง
จานระเหย2
2
Dry, sieve and calcine
Dry, sieve and calcine
Dry the slurry, crush it to pass a 50 mesh screen, moisten it with 5 % of a 2 1/2 % starch solution and press it into one slug. Calcine the slug for one hour at 1600 °F (871 °C). Ours: potato starch, a drying oven, mortar and pestle.
เครื่องมือที่ต้องใช้:
แป้งมันฝรั่ง
เตาอบตาก
ครกและสาก
ตะแกรงร่อน
เครื่องอัดไฮดรอลิก
เตาเผาอุณหภูมิสูง3
3
Press the discs
Press the discs
Grind the calcine to pass a 325 mesh screen, moisten it again with starch solution, and press small discs 3/8 inch in diameter and about 1/10 inch thick at 20,000 pounds per square inch.
เครื่องมือที่ต้องใช้:
ครกและสาก
ตะแกรงตาถี่
แป้งมันฝรั่ง
เครื่องอัดไฮดรอลิก
แม่พิมพ์อัดแผ่นกลม4
4
Fire on platinum
Fire on platinum
Fire the discs on platinum foil at 2400 °F (1316 °C) for one hour. They come out with zero absorption.
เครื่องมือที่ต้องใช้:
เตาเผาอุณหภูมิสูง
แพลทินัม5
5
Silver and lead
Silver and lead
Paint silver paint on both faces and fire the discs at 1350 °F (732 °C) for one hour. Solder tinned copper lead wires directly to the silver electrodes. Age at least a week before measuring. Ours: a fine brush and a soldering iron.
วัสดุสำหรับขั้นตอนนี้:
สีเงินชนิดเผา1 both faces
ลวดทองแดงชุบดีบุก2 leads per disc
ลวดตะกั่วบัดกรี1 a littleเครื่องมือที่ต้องใช้:
พู่กันปลายเรียวเล็ก
เตาเผาอุณหภูมิสูง
หัวแร้งบัดกรีวัสดุ
5- 19.32 ก.ตัวยึดตำแหน่ง
- 0.68 ก.ตัวยึดตำแหน่ง
- 1 both facesตัวยึดตำแหน่ง
- 2 leads per discตัวยึดตำแหน่ง
- 1 a littleตัวยึดตำแหน่ง
เครื่องมือที่จำเป็น
14- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 2 vendors sell this, none ship to you yetตัวยึดตำแหน่ง
พิมพ์เขียวนี้สร้าง
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้
