ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Chemical Splash Goggles: One Sealed Lens in a Moulded Rubber Frame (Hirschmann, 1954)
Emma

สร้างโดย

Emma

2. พฤศจิกายน 2026SE
18
0
0
1
0

Chemical Splash Goggles: One Sealed Lens in a Moulded Rubber Frame (Hirschmann, 1954)

Goggles for work with corrosive liquids. One clear plastic lens covers both eyes and sits sealed all round in a soft moulded rubber frame that seals against the face. The version for gas and corrosive liquids has no vent holes at all, and the strap passes through tabs outside the lens, so nothing can leak through or around the part you look through. Result: chemical splash goggles with a lens you can pull out and replace, and a strap pull shared evenly between lens and frame, so neither warps. Source: J. B. Hirschmann, US Patent 2,680,846 (1954), Fig. 4 version. Unknown: sizes, the rubber compound, the strap material and how the frame is moulded. Ours: the mould; the patent tested a cellulose acetate lens. Picture: patent drawing.
ระดับกลาง
2 days

คำแนะนำ

1

Mould the rubber frame

Mould the frame in one piece from rubber. The front rim has one opening shaped for both eyes, narrower above the nose. Behind it, a wall forms the eye chamber and ends in a double flange that seals against the face. Inside the rim, form a channel between an outer and an inner flange to hold the lens edge. At each end, mould a lug with a strap slot and a slit through the channel for the lens tab. For corrosive liquids, leave out all vent holes. Ours: a compression mould.

วัสดุสำหรับขั้นตอนนี้:

ยางคอมปาวด์ยางคอมปาวด์1 frame

เครื่องมือที่ต้องใช้:

แม่พิมพ์อัดขึ้นรูปแม่พิมพ์อัดขึ้นรูป
ขนาดที่ไม่ทราบขนาดที่ไม่ทราบ
2

Cut the lens

Cut one lens from flexible clear plastic, shaped to match the rim. The patent tested cellulose acetate. Leave a tab at each end, outside the area you look through. Cut a closed slot in each tab and line it with a grommet. Make two holes at the centre for the bolts. Leave no other holes in the viewing area.

วัสดุสำหรับขั้นตอนนี้:

แผ่นพลาสติกใสแผ่นพลาสติกใส1 lens
ห่วงหมุดย้ำห่วงหมุดย้ำ2 tab grommets

เครื่องมือที่ต้องใช้:

กรรไกรตัดแผ่นโลหะกรรไกรตัดแผ่นโลหะ
เหล็กตอกนำศูนย์เหล็กตอกนำศูนย์
3

Seal the lens in the frame

Spring the lens edge into the channel all the way round, pushing each tab out through its slit so it lies under the lug, slot over slot. Fasten the centre with two stainless-steel bolts and nuts. (The vented version uses snap fasteners here.)

วัสดุสำหรับขั้นตอนนี้:

สกรูเกลียวมิลสกรูเกลียวมิล2 stainless steel
น็อตหกเหลี่ยมน็อตหกเหลี่ยม2 stainless steel

เครื่องมือที่ต้องใช้:

ชุดไขควงชุดไขควง
4

Fit the head strap

Use a strap in two halves, joined at the back by a buckle, each half with a thickened end. Slide a slotted plate of metal or plastic onto each half, then thread it from the front through the lug slot and the lens-tab slot. The thick end stops against the plate and lug. The pull of the strap now goes into both lens and frame, holds the lens in, and stays outside the field of view.

วัสดุสำหรับขั้นตอนนี้:

สายรัดศีรษะแว่นครอบตาสายรัดศีรษะแว่นครอบตา1 two halves
หัวเข็มขัดทองเหลืองมีลิ้นหัวเข็มขัดทองเหลืองมีลิ้น1 ชิ้น
วัสดุที่ไม่ทราบวัสดุที่ไม่ทราบ1 two slotted plates

เครื่องมือที่ต้องใช้:

ขนาดที่ไม่ทราบขนาดที่ไม่ทราบ

วัสดุ

8

เครื่องมือที่จำเป็น

5

วัสดุจากพิมพ์เขียวที่เชื่อมต่อ

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...