ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Contrary Hinged-Dasher Air-Pump Churn: Two Crossing Dashers Fold to Gather, a Pump Blows Air Through the Cream
Philip L. Clow of Cohoes, New York, received US 26,092, dated 15 November 1859, for a churn. One crank shaft and two pairs of bevel wheels turn two upright plate dashers in opposite directions at the same speed, so close that their paths cross. Their outer parts are hinged: turned one way they stand open to churn, turned the other they fold back to gather the butter. A pump on the same shaft blows air in at the bottom, and hot or cold water under the vessel's bottom keeps the cream at the right warmth.
The patent gives no sizes; every size here is ours.
ขั้นสูง
About 2 days, plus printing
คำแนะนำ
1
1
Two dashers whose paths cross, and the air the pump gives
Two dashers whose paths cross, and the air the pump gives
กำลังโหลดสมุด Jupyter…
2
2
A turning dasher with a hinged leaf for gathering, two months before
A turning dasher with a hinged leaf for gathering, two months before
Hassler's leaf opens when the dasher is reversed. Clow hinges the outer halves of two counter-turning dashers so they fold back when reversed.
3
3
Read US 26,092
Read US 26,092
"I thus hinge the outer parts of the dashers to their central parts in order that after the butter has been produced from the milk or cream by turning the dashers in the directions pointed by the arrows x, x', the person who is churning may then, by simply turning the crank-shaft, I, and dashers, B, B', in the opposite direction, instantly lessen the extent of the space passed over or occupied by the dashers and thus increase the capacity of the churn or give room in the vessel, G, for the gathering of the butter into a mass"
4
4
Print the feet
Print the feet
A foot 30 mm across and 56 mm tall with a 10 mm recess in its top. Print three. PETG, 0.2 mm layers, 40 % infill, 4 walls.
5
5
Print the eccentric t
Print the eccentric t
A disc 90 mm across and 12 mm thick bored 12.6 mm 30 mm off its centre, for a 30 mm throw. PETG, 0.2 mm layers, 40 % infill, 4 walls.
6
6
Vessel G on its reservoir F
Vessel G on its reservoir F
Fit a brass spigot low in the side of a large pot at least 400 mm across, as the cock s. Stand the three printed feet in it and the stockpot on them, so water can lie under the stockpot's bottom and up its sides. Drill the stockpot's handle for the clamp hook m.
วัสดุสำหรับขั้นตอนนี้:
หม้อใบใหญ่1 ชิ้น
หม้อใบใหญ่1 ชิ้น
ก๊อกทองเหลือง1 ชิ้น
เส้นใย PETG1 ชิ้นเครื่องมือที่ต้องใช้:
เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)
สว่านไร้สาย
ชุดดอกสว่านใบพาย
ประแจเลื่อน7
7
Cover n, posts, shafts and bevel wheels
Cover n, posts, shafts and bevel wheels
Cut a hardwood cover 350 mm across, bored 13 mm at 55 mm either side of its middle for the dasher axes k, k', 10 mm for the thermometer and 12 mm for the air tube. Screw two posts 40 x 20 mm, 110 mm tall, on it 300 mm apart and bore them 12.8 mm 80 mm above the cover for the crank shaft I, 12 mm stainless, 442 mm long, with a crank and handle on one end. Fit the two bevel sets so the wheels on k and k' are driven from opposite sides by the pinions on I, back to back between them: the dashers then turn opposite ways at the same speed. Hold the axes in the cover with shaft collars.
วัสดุสำหรับขั้นตอนนี้:
แผ่นไม้เนื้อแข็ง1 ชิ้น
กาวไม้1 ชิ้น
สกรูไม้8 ชิ้น
แท่งสเตนเลส2 ชิ้น
ชุดเฟืองดอกจอก (เหล็กกล้า, 1:1)2 ชิ้น
Shaft Collar4 ชิ้น
ตะขอและห่วงติดเสื้อผ้า1 ชิ้น
เดือยไม้เนื้อแข็ง1 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยจิ๊กซอว์
เข็มทิศ
สว่านไร้สาย
ชุดดอกสว่าน
เลื่อยตัดเหล็ก
ตะไบ (ตะไบมือ)
ชุดไขควง
ประแจเลื่อน
ตลับเมตร8
8
Dashers B, B' with hinged leaves
Dashers B, B' with hinged leaves
From 2 mm stainless sheet cut two centre parts 50 x 220 mm and four leaves 65 x 220 mm. Fix a centre part to each axis k, k', 50 mm above the vessel's floor, and hang a leaf on each of its long edges with two small butt hinges, set so the leaves stop in line with the centre part one way and fold back the other. Set the two dashers a quarter turn apart.
วัสดุสำหรับขั้นตอนนี้:
แผ่นสเตนเลส1 ชิ้น
บานพับตู้8 ชิ้น
สกรูเกลียวมิล24 ชิ้น
นอตล็อกไนลอน24 ชิ้นเครื่องมือที่ต้องใช้:
กรรไกรตัดแผ่นโลหะ
ตะไบ (ตะไบมือ)
สว่านไร้สาย
ชุดดอกสว่าน
ชุดไขควง
ประแจเลื่อน9
9
Force-pump E and pipe u
Force-pump E and pipe u
Fix the eccentric on the crank shaft outside one post, and a 100 ml syringe upright beside it, its plunger joined to a strap round the eccentric. On its nozzle fit two check valves on a tee, one letting air in, the other out. Run silicone tube from the outlet to a stainless tube that passes down through the cover and along the vessel's side to 8 mm above its floor, its end turned inwards.
วัสดุสำหรับขั้นตอนนี้:
กระบอกฉีดยา - Luer1 ชิ้น
วาล์วกันกลับ2 ชิ้น
ท่อสเตนเลส1 ชิ้น
แผ่นไม้เนื้อแข็ง1 ชิ้น
สกรูไม้4 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยตัดเหล็ก
ตะไบ (ตะไบมือ)
สว่านไร้สาย
ชุดดอกสว่าน
ชุดไขควง10
10
The build in 3D
The build in 3D
FreeCAD model of this build, the vessel, reservoir and cover cut through: the stockpot on its feet in the water pot, the two dashers on their axes a quarter turn apart, the bevel wheels and crank shaft on their posts, the eccentric and syringe pump, the air tube and the thermometer. The dashers were turned through a full turn with their leaves open and folded.
11
11
Churn, then gather
Churn, then gather
Fill the reservoir with warm or cold water until the cream will sit at about 15 °C. Pour about 12 litres of heavy cream into the stockpot, set the cover with the dashers in, hook it down, and put the thermometer through it. Turn the crank so the leaves stand open, timing it, while the pump bubbles air in at the bottom. When the butter comes, turn the crank the other way: the leaves fold back and the dashers gather the butter. Lift the cover and dashers out, gather the butter, empty the reservoir by the spigot, drain the buttermilk, wash the butter in cold water until it runs clear, salt and weigh it.
วัสดุสำหรับขั้นตอนนี้:
ครีมสด12 l
เกลือทะเลเม็ดหยาบ1 ชิ้น
น้ำ1 ชิ้นเครื่องมือที่ต้องใช้:
เทอร์มอมิเตอร์หัววัดแบบเสียบค้าง
นาฬิกาจับเวลา
เครื่องชั่งดิจิทัลสำหรับครัว
ชามผสมสเตนเลสใบใหญ่
กาต้มน้ำไฟฟ้า12
12
Troubleshooting
Troubleshooting
Contrary-dasher churn troubleshooting.
Flow
Loading...
13
13
History and honest limits
History and honest limits
**Philip L. Clow** of Cohoes, Albany County, New York, US 26,092, 15 November 1859, "Churn". He claimed the outer parts of the two contrarily revolving dashers hung to the central parts by hinges d, and the arrangement of the air-pump E and water-reservoir F with the revolving dashers and cream vessel. The patent gives no sizes; every size here is ours. His force-pump is not described inside: ours is a syringe with two check valves on an eccentric. His reservoir is a closed chamber under the vessel with a funnel, air-vent and cock; ours is an open pot of water with a spigot. His rubber packing between the pinions is left out.
วัสดุ
23- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 12 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 4 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 8 ชิ้นตัวยึดตำแหน่ง
- 24 ชิ้นตัวยึดตำแหน่ง
- 24 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 12 lตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
เครื่องมือที่จำเป็น
17- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
ไฟล์ออกแบบ
3พิมพ์เขียวนี้สร้าง
บลูพริ้นท์ที่เกี่ยวข้อง
บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

Rocking-Churns Water-Jacket Churn: Two Small Churns Rock and Their Dashers Plunge, Wings Turn Above
โดย Buttercup
งานไม้
17
0
0
0
0
0

Hinged-Leaf Wing Dasher Churn: Turn One Way to Churn, Reverse and a Leaf Opens to Gather the Butter
โดย Buttercup
งานไม้
8
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
โดย TheChef
งานฝีมือ
63
0
0
0
0
0
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

