ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Folding-Lever Dasher Churn: The Dash Rod Folds Two Levers and Swings the Agitators Side to Side
N. B. Cooper of Gratis, Ohio, received US 26,020, dated 8 November 1859, for a churn-dasher. A frame slides into ways on the churn's ends and lifts out whole. Two bars run along its foot on pivots, one each side of the middle, each with blades and the lower half of a folding lever; the levers' upper halves meet at the dash rod. Working the rod up and down folds the levers and swings the bars and their agitators, driving the cream from side to side.
The patent gives no sizes; every size here is ours.
ระดับกลาง
About 2 days
คำแนะนำ
1
1
The folding levers
The folding levers
กำลังโหลดสมุด Jupyter…
2
2
Dashers that swing sideways, six weeks before
Dashers that swing sideways, six weeks before
Austin swung his side dashers from cranks. Cooper swings his agitators from the dash rod itself, by folding levers.
3
3
Read US 26,020
Read US 26,020
"It will be readily seen by reference to Fig. 2 that the operation of the levers and agitators is of such a character as to force the cream rapidly from one side of the churn to the other, and that such currents must be forcibly interrupted by the agitators upon either side"
4
4
Shell A and ways x
Shell A and ways x
From 20 mm hardwood make a box 400 x 320 mm and 420 mm deep inside. Glue two strips 15 x 15 mm up the inside of each end, 90 mm apart, as the ways x. Fill the box with water overnight so it swells tight, then empty it.
วัสดุสำหรับขั้นตอนนี้:
แผ่นไม้เนื้อแข็ง3 ชิ้น
กาวไม้1 ชิ้น
สกรูไม้24 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยวงเดือนตั้งโต๊ะ
เลื่อยมือ
สว่านไร้สาย
ชุดดอกสว่าน
แคลมป์แบบบาร์
ฉากตาย
ตลับเมตร
น้ำ5
5
Frame B
Frame B
Cut two end posts 89 x 14 mm, 460 mm long, to slide between the ways, and a top bar 400 x 40 x 30 mm with a 31 mm square hole in its middle for the dash rod; screw the bar across the posts' tops. Screw a block 16 x 24 x 24 mm to each post's inside 25 mm each side of the middle and 110 mm up, and bore them 10.4 mm for the pivot rods b'.
วัสดุสำหรับขั้นตอนนี้:
แผ่นไม้เนื้อแข็ง1 ชิ้น
กาวไม้1 ชิ้น
สกรูไม้12 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยวงเดือนตั้งโต๊ะ
สิ่วเจาะเดือย
ค้อนไม้
สว่านไร้สาย
ชุดดอกสว่าน
ฉากตาย6
6
Bars b, blades c and folding levers d
Bars b, blades c and folding levers d
Bore two hardwood bars 20 mm square and 336 mm long through their length, 10.4 mm, and pin each on a 10 mm stainless rod 396 mm long that turns in the blocks. In the middle of each bar fix a lower arm, 110 mm between its pin holes, pointing up and out, and fix two blades 54 x 50 x 8 mm at right angles to it, pointing down and out, staggered so the two bars' blades pass each other. Join each arm's end to an upper lever, 180 mm between pins, and both upper levers to the foot of a dash rod 30 mm square and 550 mm long, with 10 mm stainless pins, washers and split pins. Glue two agitator bars f, 16 mm square and 340 mm long, across each upper lever.
วัสดุสำหรับขั้นตอนนี้:
แผ่นไม้เนื้อแข็ง2 ชิ้น
แท่งสเตนเลส2 ชิ้น
เดือยไม้เนื้อแข็ง1 ชิ้น
กาวไม้1 ชิ้น
แหวนรองแบน8 ชิ้น
สลักผ่า8 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยวงเดือนตั้งโต๊ะ
เลื่อยตัดเหล็ก
ตะไบ (ตะไบมือ)
สว่านไร้สาย
ชุดดอกสว่าน
กระดาษทราย
ตลับเมตร7
7
The build in 3D
The build in 3D
FreeCAD model of this build, one side and one end left off: the shell with its ways, the frame with the pivot rods and the dash rod, the two bars with their arms and blades, the upper levers with the agitator bars. The bars were turned from 40 degrees up to 40 degrees down.
8
8
Churn
Churn
Pour about 25 litres of heavy cream at about 15 °C into the shell, checked with the thermometer. Slide the frame down the ways and work the dash rod up and down steadily, timing it. When the butter comes, lift the frame out whole, gather the butter, drain the buttermilk, wash the butter in cold water until it runs clear, salt and weigh it.
วัสดุสำหรับขั้นตอนนี้:
ครีมสด25 l
เกลือทะเลเม็ดหยาบ1 ชิ้น
น้ำ1 ชิ้นเครื่องมือที่ต้องใช้:
เทอร์มอมิเตอร์หัววัดแบบเสียบค้าง
นาฬิกาจับเวลา
เครื่องชั่งดิจิทัลสำหรับครัว
ชามผสมสเตนเลสใบใหญ่9
9
Troubleshooting
Troubleshooting
Folding-lever churn troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**N. B. Cooper** of Gratis, Preble County, Ohio, US 26,020, 8 November 1859, "Churn-Dasher". He did not claim jointed levers or agitators on them, "as these devices are well known", but "the arrangement of the arms d, d, on the two pivots b', b', one on each side of the upright B, when the upright B is made removable, by means of the ways x, x". The patent gives no sizes; every size here is ours. His central upright is here the top bar's guide, and the rod is worked by hand rather than by gearing and a crank.
วัสดุ
10- 3 ชิ้นตัวยึดตำแหน่ง
- 3 ชิ้นตัวยึดตำแหน่ง
- 36 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 8 ชิ้นตัวยึดตำแหน่ง
- 8 ชิ้นตัวยึดตำแหน่ง
- 25 lตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
เครื่องมือที่จำเป็น
17- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
ไฟล์ออกแบบ
1พิมพ์เขียวนี้สร้าง
บลูพริ้นท์ที่เกี่ยวข้อง
บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

Three-Crank Churn: One Dasher Strokes Up and Down While Two Side Dashers Swing In and Out
โดย Buttercup
งานไม้
14
0
0
0
0
0

Oval-Breaker Rod Dasher: Breakers Strung on Two Rods, Add More for More Agitation
โดย Buttercup
งานไม้
6
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
โดย TheChef
งานฝีมือ
63
0
0
0
0
0
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

