ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Spring-Lever Dasher Churn: A Hand Lever and a Faster Bar on a Post Drive the Old Dasher Down, a Rubber Spring Lifts It
Buttercup

สร้างโดย

Buttercup

11. พฤศจิกายน 2026IE
8
0
0
0
0

Spring-Lever Dasher Churn: A Hand Lever and a Faster Bar on a Post Drive the Old Dasher Down, a Rubber Spring Lifts It

N. B. Cooper of Gratis, Ohio, received US 28,970, dated 3 July 1860, for a device to work the old upright dasher churn more easily. A post beside the churn carries a long hand lever and, on an adjustable block, a shorter bar linked to the dasher handle. The two are joined so the bar moves faster than the lever; pressing the lever down drives the dasher into the cream, and an india-rubber spring lifts everything again, like a pump on a spring pole. The block slides to suit churns of any height. The patent gives no sizes; every size here is ours.
ระดับกลาง
About 2 days

คำแนะนำ

1

Why the bar d runs ahead of the lever

กำลังโหลดสมุด Jupyter…
2

A churn worked against a spring, four months before

Cunningham's spring pole drives the dasher down. Cooper's rubber spring lifts it back up, and the hand drives it down.
3

Read US 28,970

"The labor of lifting and returning the ordinary churn dasher by the smooth vertical handle, is by my process, or that which my improvement introduces, changed to an easy downward pressure upon a nearly horizontal bar or handle, the parts returning upwardly to their place by the force of the spring which was easily overcome by the downward pressure."
4

Base B, churn A, cover C and dasher D

Screw a hardwood base 520 x 400 mm and stand the bucket on it, held by a few cleats round its foot, as the patent says. Cut an HDPE cover with a 28 mm hole in the middle. Make a dasher of two crossed hardwood boards 220 x 40 x 16 mm on a 25 mm hardwood handle long enough to stand 300 mm above the cover.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง2 ชิ้น
ถังขนาด 20 ลิตรถังขนาด 20 ลิตร1 ชิ้น
แผ่น HDPEแผ่น HDPE1 ชิ้น
เดือยไม้เนื้อแข็งเดือยไม้เนื้อแข็ง1 ชิ้น
กาวไม้กาวไม้1 ชิ้น
สกรูไม้สกรูไม้12 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยวงเดือนตั้งโต๊ะเลื่อยวงเดือนตั้งโต๊ะ
เลื่อยจิ๊กซอว์เลื่อยจิ๊กซอว์
ชุดดอกสว่านใบพายชุดดอกสว่านใบพาย
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
ชุดไขควงชุดไขควง
5

Standard E with slot a and holes b; block c

Glue up a hardwood standard 60 x 40 mm, 800 tall, and frame it into the base behind the churn, 210 mm from its centre. Rout a slot a 18 mm wide through it from 480 to 700 mm up, and bore 10.4 mm holes b across it every 30 mm. Make a hardwood block c that slides in the slot with shoulders bearing on both faces, with a 10 mm stainless pin through a hole b to set its height, and a tail behind the standard for the spring k.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง1 ชิ้น
กาวไม้กาวไม้1 ชิ้น
แท่งสเตนเลสแท่งสเตนเลส1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยวงเดือนตั้งโต๊ะเลื่อยวงเดือนตั้งโต๊ะ
เราเตอร์เราเตอร์
ชุดสิ่วไม้ชุดสิ่วไม้
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
แคลมป์แบบบาร์แคลมป์แบบบาร์
6

Lever F, piece g, block i, bar d and links e, f

Cut a hardwood lever F 28 x 16 mm, 810 long, and a piece g 340 long. Pivot both on a 10 mm stainless pin through a hole b 620 mm up, F on one face of the standard and g on the other, 110 mm of each behind it, and join them there with a pin j. At the churn's centre join them with a hardwood block i with a 28 mm upright hole for the dasher handle. Cut a hardwood bar d 24 x 16 mm, pivot it on the block c 55 mm from its back end, and join its back end to the pin j with two mild steel flat bar links f, 71 mm between holes. Join d's front end, 170 mm out, to the dasher handle with a flat bar link e 80 mm long hanging down to a pin m through the handle; bore the hole m where the dasher rests on the bottom with the levers level.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง1 ชิ้น
แท่งสเตนเลสแท่งสเตนเลส1 ชิ้น
เหล็กแบนกล้าละมุนเหล็กแบนกล้าละมุน1 ชิ้น
สลักเกลียวหัวกลมสลักเกลียวหัวกลม4 ชิ้น
นอตล็อกไนลอนนอตล็อกไนลอน4 ชิ้น
สลักผ่าสลักผ่า4 ชิ้น
กาวไม้กาวไม้1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยวงเดือนตั้งโต๊ะเลื่อยวงเดือนตั้งโต๊ะ
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ตะไบ (ตะไบมือ)ตะไบ (ตะไบมือ)
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
ประแจเลื่อนประแจเลื่อน
7

Springs k and l

Loop a length of elastic cord round the pin j and tie both ends to the block c's tail, tight enough to lift the lever and dasher when let go: the spring k. Tie a shorter loop from the bar d to the lever F as the spring l.

วัสดุสำหรับขั้นตอนนี้:

เชือกยางยืดเชือกยางยืด1 ชิ้น

เครื่องมือที่ต้องใช้:

ตลับเมตรตลับเมตร
8

The build in 3D

FreeCAD model of this build, the churn cut open: the standard with its slot and holes, the block c, the lever F and piece g with the block i round the dasher handle, the bar d with links e and f, the rubber springs, and the dasher.
ไฟล์แบบBLENDCC0 - Free
9

Churn

Pour about 8 litres of heavy cream at about 15 °C, checked with the thermometer, into the churn and put on the cover. Set the block c so a full press of the handle brings the dasher near the bottom and the spring lifts it clear of the cream. Press the handle down and let it rise, steadily, timing it. When the butter comes, unpin the link e, lift out the dasher, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

วัสดุสำหรับขั้นตอนนี้:

ครีมสดครีมสด8 l
เกลือทะเลเม็ดหยาบเกลือทะเลเม็ดหยาบ1 ชิ้น
น้ำน้ำ1 ชิ้น

เครื่องมือที่ต้องใช้:

เทอร์มอมิเตอร์หัววัดแบบเสียบค้างเทอร์มอมิเตอร์หัววัดแบบเสียบค้าง
นาฬิกาจับเวลานาฬิกาจับเวลา
เครื่องชั่งดิจิทัลสำหรับครัวเครื่องชั่งดิจิทัลสำหรับครัว
ชามผสมสเตนเลสใบใหญ่ชามผสมสเตนเลสใบใหญ่
10

Troubleshooting

Spring-lever churn troubleshooting.

Flow

Loading...
11

History and honest limits

**N. B. Cooper** of Gratis, Preble County, Ohio, US 28,970, 3 July 1860, "Churn". He claimed the mechanism of base, upright, block, hand lever, pivoted bar, links and springs together, to make the old dasher churn lighter work, likening it to a pump on a "spring pole". His springs are india rubber; ours are elastic cord. Every size here is ours.

วัสดุ

15

เครื่องมือที่จำเป็น

18

ไฟล์ออกแบบ

1

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...