ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Electric Arc Furnace: the Héroult Series-Arc Steel Furnace (Stansfield, 1914)
Volt

สร้างโดย

Volt

4. พฤศจิกายน 2026SE
19
0
0
0
0

Electric Arc Furnace: the Héroult Series-Arc Steel Furnace (Stansfield, 1914)

Héroult's steel furnace: a tilting hearth like an open-hearth furnace, lined with dolomite, with two carbon electrodes coming down through the roof. The current goes down one electrode, arcs into the slag, passes through the molten steel and arcs back up the other, so the heat goes straight into the metal. Result: an electric steel furnace about 7 x 4 ft inside for a 3 ton charge, run at about 350 kW and 110 V. Source: A. Stansfield, The Electric Furnace, 2nd ed. (1914), pp. 115-116, 214-216. Unknown: case and tilting gear details, electrode size. Picture: a drawn diagram (Fig. 93 is blank in the scan).
ผู้เชี่ยวชาญ
Unknown

คำแนะนำ

1

Build the case and lining

Build the furnace in a steel case on a tilting mounting, about 7 x 4 ft inside, with charging doors at the ends. Line it with dolomite bricks and crushed dolomite; dolomite or magnesite on the hearth, which allows strongly basic slags. Ours: mild steel plate. Not given: the case and tilting gear, the bricks' making.

วัสดุสำหรับขั้นตอนนี้:

แผ่นเหล็กกล้าละมุนแผ่นเหล็กกล้าละมุน1 case
โดโลไมต์ (หินปูนแมกนีเซียม)โดโลไมต์ (หินปูนแมกนีเซียม)1 lining and crushed dolomite
ก้อนแมกนีไซต์ก้อนแมกนีไซต์1 hearth, if magnesite

เครื่องมือที่ต้องใช้:

เครื่องเชื่อมอาร์กเครื่องเชื่อมอาร์ก
เกรียงก่อเกรียงก่อ
ขนาดที่ไม่ทราบขนาดที่ไม่ทราบ
2

Make the removable roof

Make the roof of silica brick, covered with steel plates and given eyes so it can be lifted off. Between the two electrode holes use bronze plates instead of steel, because steel there would raise the inductance of the AC circuit. Fit water jackets round each electrode hole for a close fit, so less heat escapes and the electrodes do not burn in the air. Ours: copper tube for the water jackets. Silica brick has no head here.

วัสดุสำหรับขั้นตอนนี้:

วัสดุที่ไม่ทราบวัสดุที่ไม่ทราบ1 silica brick
แผ่นเหล็กกล้าละมุนแผ่นเหล็กกล้าละมุน1 roof plates
แผ่นทองสัมฤทธิ์แผ่นทองสัมฤทธิ์1 plates between electrodes
ท่อทองแดงท่อทองแดง1 water jackets

เครื่องมือที่ต้องใช้:

เครื่องเชื่อมอาร์กเครื่องเชื่อมอาร์ก
สว่านแท่นสว่านแท่น
น้ำน้ำ
3

Hang the electrodes

Use two vertical carbon electrodes, square in section. Carry each in a holder on an arm supported by the furnace itself, so its height does not change when the furnace tilts: four contact pieces round the electrode, drawn tight by a steel strap and a screw in the arm, with the cable bolted to them. Raise and lower each electrode separately, by a regulator controlled by the voltage between it and the metal. Not given: electrode size, the regulator's build.

วัสดุสำหรับขั้นตอนนี้:

ขั้วไฟฟ้าคาร์บอนขั้วไฟฟ้าคาร์บอน2 electrodes
โลหะที่ไม่ทราบโลหะที่ไม่ทราบ1 holders, arms, contact pieces

เครื่องมือที่ต้องใช้:

สว่านแท่นสว่านแท่น
4

Melt and refine a charge

Charge steel scrap with some iron ore and lime. Keep each electrode a little above the slag, leaving room for its arc. Regulate the current by hand while the scrap melts, then switch to automatic; full power only after about an hour. Pour off the slag and make a second, then a third, with lime and a little sand and fluorspar, before the final additions. At La Praz this took about 350 kW at 110 V: 5 hours for 1.25 tons of low-carbon steel, 8 hours for 2.33 tons of high-carbon steel. Not given: the electric supply.

เครื่องมือที่ต้องใช้:

น้ำน้ำ

วัสดุ

8

เครื่องมือที่จำเป็น

5

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...