ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Electrolytic Capacitors: Borate Paper Wound with Formed Aluminium Foil and Vacuum-Impregnated (Danziger, US 2,107,780)
Ed

สร้างโดย

Ed

2. พฤศจิกายน 2026FI
12
0
0
0
0

Electrolytic Capacitors: Borate Paper Wound with Formed Aluminium Foil and Vacuum-Impregnated (Danziger, US 2,107,780)

A dry electrolytic capacitor wound from aluminium foil and paper. The paper is first soaked in ammonium borate and dried, so the salt is already in its fibres. After winding, the bodies are soaked under heat and vacuum in borate dissolved in glycol, boxed and aged at 500 volts. Result: electrolytic capacitors. In the patent's tests these lost only 4.8 % of their capacity, against about 33 % for bodies made the ordinary way, and their power-factor loss rose 87 % on life test against 250 %. Source: H. I. Danziger and A. Di Giacomo, US 2,107,780 (1938). Unknown: how the anode foil is formed, which paper, the tab metal, and how the ammonium borate is made; the patent does not give them. Picture: Wikimedia Commons.
ขั้นสูง
1 day

คำแนะนำ

1

Salt the paper

Draw the paper strip through a saturated solution of ammonium borate in water, about 15 to 30 seconds for each part of it, then dry it at about 80 °C for about 15 seconds and reel it up. The salted paper keeps until needed. Unknown: which paper. Ours: a tray for the bath and a drying oven.

วัสดุสำหรับขั้นตอนนี้:

กระดาษคั่นตัวเก็บประจุกระดาษคั่นตัวเก็บประจุ1 strip
แอมโมเนียมบอเรตแอมโมเนียมบอเรต1 to saturate

เครื่องมือที่ต้องใช้:

น้ำน้ำ
ถาดถาด
เตาอบตากเตาอบตาก
2

Wind the bodies

On a winding machine, wind two aluminium foil strips with the salted paper between them onto a mandrel; at least one foil must already carry its electrolytic film. One paper strip is enough. Let the paper stand out at both ends, bring a connection tab out of each end, cut the strips and hold the body wound with a rubber band. Unknown: how the foil was formed, and the tab metal.

วัสดุสำหรับขั้นตอนนี้:

แผ่นอะลูมิเนียมที่ขึ้นรูปฟิล์มแผ่นอะลูมิเนียมที่ขึ้นรูปฟิล์ม1 strip
แผ่นฟอยล์อะลูมิเนียมแผ่นฟอยล์อะลูมิเนียม1 strip
โลหะที่ไม่ทราบโลหะที่ไม่ทราบ2 tabs

เครื่องมือที่ต้องใช้:

เครื่องม้วนตัวเก็บประจุเครื่องม้วนตัวเก็บประจุ
ยางรัดยางรัด
3

Make the impregnant

Heat ethylene glycol to about 90 °C, then stir in powdered ammonium borate slowly and continuously until the solution reaches about 122 °C. Ours: a hot plate and thermometer.

วัสดุสำหรับขั้นตอนนี้:

เอทิลีนไกลคอลเอทิลีนไกลคอล1 as required
แอมโมเนียมบอเรตแอมโมเนียมบอเรต1 as required

เครื่องมือที่ต้องใช้:

แผ่นให้ความร้อนแผ่นให้ความร้อน
เทอร์โมมิเตอร์เทอร์โมมิเตอร์
4

Soak under heat and vacuum

Rack the bodies in a vacuum tank heated to about 50 °C and draw about 745 mm of vacuum for about an hour to pull out air and moisture. Draw in the impregnant at about 85 °C, ease the vacuum to about 310 mm, and hold at about 85 °C for about another hour.

เครื่องมือที่ต้องใช้:

ภาชนะสุญญากาศแบบมีแจ็กเก็ตไอน้ำภาชนะสุญญากาศแบบมีแจ็กเก็ตไอน้ำ
ปั๊มสุญญากาศปั๊มสุญญากาศ
เทอร์โมมิเตอร์เทอร์โมมิเตอร์
5

Box and age

Take the bodies out, put them in cardboard containers, and age them at about 500 volts DC for about three hours.

วัสดุสำหรับขั้นตอนนี้:

ท่อกระดาษแข็งท่อกระดาษแข็ง1 per capacitor

เครื่องมือที่ต้องใช้:

แหล่งจ่ายไฟตรงแรงสูง (ตั้งโต๊ะ)แหล่งจ่ายไฟตรงแรงสูง (ตั้งโต๊ะ)

วัสดุ

7

เครื่องมือที่จำเป็น

10

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...