ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่

Oblique-Slat Barrel Churn: Rows of Slats Inside a Turning Barrel Point Opposite Ways and Throw the Cream End to End
Pearson Embree of West Chester, Pennsylvania, received US 27,536, dated 20 March 1860, for a churn. Inside a common barrel churn turned by a crank, rows of wooden slats about a quarter of the diameter high point obliquely to the barrel's motion, each row the opposite way to the last. Some throw the cream toward one end, some toward the other; it strikes other slats or the projections on the heads and turns back.
The slats' height follows the patent's proportion; every other size here is ours.
ระดับกลาง
About 2 days
คำแนะนำ
1
1
Slats a quarter of the diameter high
Slats a quarter of the diameter high
กำลังโหลดสมุด Jupyter…
2
2
Cream thrown end to end, two weeks before
Cream thrown end to end, two weeks before
Newbrough rocks his barrel so the cream runs end to end through pins. Embree turns his, and oblique slats throw it.
3
3
Read US 27,536
Read US 27,536
"The slats A A A, etc., throw the cream toward an end of the churn (one portion of the slats throwing to one end and the remaining portion to the other end); as the cream is thrown violently toward the end it either strikes other slats, or the projections B B by either of which means its course is reversed and great agitation of the cream produced."
4
4
Barrel, heads and door
Barrel, heads and door
Cut 430 mm of food-grade PE pipe 315 mm across with a 12 mm wall. Cut two heads from 15 mm HDPE sheet to fit inside it and bore both 20 mm on the centre. Cut a door 200 x 120 mm in the pipe's side, between two rows of slats; keep the piece, screw two HDPE strips along its long edges so it rests on the pipe, and hold it with two hooks and eyes.
วัสดุสำหรับขั้นตอนนี้:
ท่อพอลิเอทิลีนความหนาแน่นสูง1 ชิ้น
แผ่น HDPE1 ชิ้น
ตะขอและห่วงติดเสื้อผ้า2 ชิ้น
สกรูเกลียวมิล4 ชิ้น
นอตล็อกไนลอน4 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยจิ๊กซอว์
สว่านไร้สาย
ชุดดอกสว่าน
ชุดดอกสว่านใบพาย
ตะไบ (ตะไบมือ)
ชุดไขควง
ตลับเมตร5
5
Slats A, A', A'', A''' and projections B
Slats A, A', A'', A''' and projections B
Cut four hardwood strips 30 x 18 mm, 390 long, and sixteen hardwood slats 90 x 12 mm standing 73 mm from the barrel's wall, a quarter of its 291 mm inside diameter; round their ends if you like. Set four slats in each strip, 100 mm apart, each at 45 degrees to the strip: in the first and third strips one way, in the second and fourth the other. Screw the strips inside the barrel a quarter turn apart, through the wall with stainless screws and lock nuts, sealed with silicone, so each row points the opposite way from the row before. Screw two hardwood projections B, 20 x 90 mm and 30 deep, on each head's inner face, opposite each other, between the rows.
วัสดุสำหรับขั้นตอนนี้:
แผ่นไม้เนื้อแข็ง1 ชิ้น
กาวไม้1 ชิ้น
สกรูเกลียวมิล16 ชิ้น
นอตล็อกไนลอน16 ชิ้น
สกรูไม้8 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยวงเดือนตั้งโต๊ะ
ไม้โปรแทรกเตอร์
สว่านไร้สาย
ชุดดอกสว่าน
แคลมป์แบบบาร์
กระดาษทราย
ชุดไขควง
ประแจเลื่อน6
6
Shaft, stand and crank
Shaft, stand and crank
Pass a 20 mm stainless shaft 680 mm long through both heads, press the heads into the pipe's ends, screw them through the wall and seal the heads and the shaft's passages with silicone sealant. Make a hardwood stand: a base 600 x 400 mm and two uprights 40 x 120 mm, 30 mm beyond each end of the barrel, bored 20.8 mm 260 mm above the floor. Rest the shaft in them with collars, and fit a hardwood crank 130 mm long with a dowel handle on its long end.
วัสดุสำหรับขั้นตอนนี้:
แท่งสเตนเลส1 ชิ้น
สกรูเกลียวมิล8 ชิ้น
แผ่นไม้เนื้อแข็ง2 ชิ้น
กาวไม้1 ชิ้น
สกรูไม้8 ชิ้น
Shaft Collar2 ชิ้น
เดือยไม้เนื้อแข็ง1 ชิ้นเครื่องมือที่ต้องใช้:
เลื่อยตัดเหล็ก
ตะไบ (ตะไบมือ)
เลื่อยวงเดือนตั้งโต๊ะ
สว่านไร้สาย
ชุดดอกสว่าน
ชุดดอกสว่านใบพาย
ชุดไขควง7
7
The build in 3D
The build in 3D
FreeCAD model of this build, the barrel cut through the middle: four rows of oblique slats, alternate rows pointing opposite ways, the projections B on the heads, the door, the shaft, stand and crank.
8
8
Churn
Churn
Turn the door uppermost, pour in about 8 litres of heavy cream at about 15 °C, checked with the thermometer, and close it. Turn the crank steadily, timing it. When the butter comes, stop with the door uppermost, open it, tip the buttermilk out into a bowl, take out the butter, wash it in cold water until it runs clear, salt and weigh it.
วัสดุสำหรับขั้นตอนนี้:
ครีมสด8 l
เกลือทะเลเม็ดหยาบ1 ชิ้น
น้ำ1 ชิ้นเครื่องมือที่ต้องใช้:
เทอร์มอมิเตอร์หัววัดแบบเสียบค้าง
นาฬิกาจับเวลา
เครื่องชั่งดิจิทัลสำหรับครัว
ชามผสมสเตนเลสใบใหญ่9
9
Troubleshooting
Troubleshooting
Oblique-slat barrel churn troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**Pearson Embree** of West Chester, Chester County, Pennsylvania, US 27,536, 20 March 1860, "Churn". He claimed the slats or projections on the inner surface, each row pointing obliquely in the line of motion and the next row the opposite way. He says they make butter "in much less time than by the ordinary revolving churns". The slat height follows his quarter-diameter; the PE barrel, the 45-degree angle, the counts and all other sizes are ours.
วัสดุ
15- ตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 28 ชิ้นตัวยึดตำแหน่ง
- 20 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 16 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 2 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 8 lตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
- 1 ชิ้นตัวยึดตำแหน่ง
เครื่องมือที่จำเป็น
17- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- 1 vendor sell this, none ship to you yetตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
- ตัวยึดตำแหน่ง
ไฟล์ออกแบบ
1พิมพ์เขียวนี้สร้าง
บลูพริ้นท์ที่เกี่ยวข้อง
บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

Rocking Barrel Brake-Pin Churn: Cream Rushes End to End Through Rows of Pins, a Diagonal Board Gathers the Butter
โดย Buttercup
งานไม้
8
0
0
0
0
0

Counter-Turning Cylinder Churn: The Ribbed Cylinder Turns One Way While the Dashers Inside Turn the Other
โดย Buttercup
งานไม้
10
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
โดย TheChef
งานฝีมือ
63
0
0
0
0
0
CC0 สาธารณสมบัติ
พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต
สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

