ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Gas Burner: a Home-Made Bunsen Burner from Brass Tube (Work, 1892)
Charlie

สร้างโดย

Charlie

7. พฤศจิกายน 2026DE
12
0
0
0
0

Gas Burner: a Home-Made Bunsen Burner from Brass Tube (Work, 1892)

A Bunsen burner: gas from a fine jet draws air in through two holes at the foot of an upright tube, and the mixture burns at the top with a hot blue flame that leaves no soot. H. B. Stocks (Work, 1892) makes one from a 3 1/2 in. brass tube 1/2 in. across, a short 3/8 in. tube for the gas, a brass boss and elbow from a gas bracket, and a bit of fine-bore tube from an old oil-can as the jet. A sliding brass collar over the air-holes sets the flame. Source: H. B. Stocks, How to Make a Cheap Spirit Lamp, Bunsen Burner, Blowpipes, etc., Work No. 167 (28 May 1892), p. 167. Picture: his Figs. 3-4.
ระดับกลาง
Unknown

คำแนะนำ

1

Read Stocks

"To make a Bunsen burner the following materials will be necessary:—A piece of brass tube 3 1/2 in. long, 1/2 in. diameter (external); a piece of tube 3/8 in. in diameter, 1 1/2 in. long; a brass boss similar to those on an ordinary bracket, but without a tap; a brass elbow tube; also a piece of tubing with very fine bore (small bit of tube from an old oil-can will do)."
2

Solder the elbow on the boss

Solder the brass elbow-piece onto the brass boss, with the tube that has a screw cut for a gallery uppermost.

วัสดุสำหรับขั้นตอนนี้:

ข้อต่อท่อเกลียวข้อต่อท่อเกลียว2 boss and elbow
ตะกั่วบัดกรีดีบุก-ตะกั่วตะกั่วบัดกรีดีบุก-ตะกั่ว1 joint
ฟลักซ์ฟลักซ์1 joint

เครื่องมือที่ต้องใช้:

หัวแร้งบัดกรีหัวแร้งบัดกรี
3

Fit the jet

Cut the fine-bore tube 3/4 in. to 1 in. long and solder it inside the vertical tube of the elbow-piece so it projects about 1/2 in. If it is too small for the hole, plug round it with a little sheet lead, keeping it perfectly vertical and in the centre of the outer tube, then solder. The metal of the oil-can tube is not given (unknown).

วัสดุสำหรับขั้นตอนนี้:

โลหะที่ไม่ทราบโลหะที่ไม่ทราบ1 fine-bore tube
แผ่นตะกั่วแผ่นตะกั่ว1 packing
ตะกั่วบัดกรีดีบุก-ตะกั่วตะกั่วบัดกรีดีบุก-ตะกั่ว1 joint

เครื่องมือที่ต้องใช้:

หัวแร้งบัดกรีหัวแร้งบัดกรี
กรรไกรตัดแผ่นโลหะกรรไกรตัดแผ่นโลหะ
4

Make the burner tube

Take the brass tube 3 1/2 in. long, 1/2 in. across. If it is not of very thick brass it will be a little too large: turn a piece of very thin sheet brass 1/2 in. by 1 1/4 in. into a cylinder and solder it inside one end. Tap that end inside to screw onto the male thread of the elbow-piece. At the same end drill two holes about 3/8 in. across, exactly opposite each other, their centres 5/8 in. from the end: the air-holes.

วัสดุสำหรับขั้นตอนนี้:

ท่อทองเหลือง เส้นผ่านศูนย์กลางนอก 1/2 นิ้วท่อทองเหลือง เส้นผ่านศูนย์กลางนอก 1/2 นิ้ว1 3 1/2 in.
แผ่นทองเหลืองแผ่นทองเหลือง1 1/2 x 1 1/4 in.
ตะกั่วบัดกรีดีบุก-ตะกั่วตะกั่วบัดกรีดีบุก-ตะกั่ว1 joint

เครื่องมือที่ต้องใช้:

กรรไกรตัดแผ่นโลหะกรรไกรตัดแผ่นโลหะ
หัวแร้งบัดกรีหัวแร้งบัดกรี
ชุดต๊าปและดายทำเกลียวชุดต๊าปและดายทำเกลียว
ด้ามจับต๊าปเกลียวด้ามจับต๊าปเกลียว
สว่านมือสว่านมือ
5

Assemble and test

Screw the burner tube onto the elbow-piece and screw the 3/8 in. tube, 1 1/2 in. long, into the side opening. Push the india-rubber tube from the gas supply onto the side tube and light. A purplish-blue flame means air and gas are in the right proportion. A yellow tip means too much gas: plug the hole in the jet slightly.

วัสดุสำหรับขั้นตอนนี้:

ท่อทองเหลือง เส้นผ่านศูนย์กลางนอก 9.5 มม.ท่อทองเหลือง เส้นผ่านศูนย์กลางนอก 9.5 มม.1 1 1/2 in.

เครื่องมือที่ต้องใช้:

ท่อยางท่อยาง
6

Fit the air collar

If the gas burns with a green flame and a hissing noise, the air-holes are too large. Cut sheet brass about 3/4 in. wide and 1 3/4 in. long and drill two holes 3/8 in. across, 1/2 in. from each end (their centres 3/16 in. further in). Turn it into a tube and push it onto the burner tube over the air-holes. Turn it until the two sets of holes do not quite match, so the right amount of air reaches the burner.

วัสดุสำหรับขั้นตอนนี้:

แผ่นทองเหลืองแผ่นทองเหลือง1 3/4 x 1 3/4 in.

เครื่องมือที่ต้องใช้:

กรรไกรตัดแผ่นโลหะกรรไกรตัดแผ่นโลหะ
สว่านมือสว่านมือ

วัสดุ

8

เครื่องมือที่จำเป็น

6

พิมพ์เขียวนี้สร้าง

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...