ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
A Set of Cold Chisels: Flat, Gouge, Side, Cape, Diamond-Point and Round-Nose, Edge Hardened Only, Tempered Purple (Griswold, 1904)
Forge

สร้างโดย

Forge

14. พฤศจิกายน 2026NO
12
0
0
0
0

A Set of Cold Chisels: Flat, Gouge, Side, Cape, Diamond-Point and Round-Nose, Edge Hardened Only, Tempered Purple (Griswold, 1904)

Robert Gibson Griswold's working set of cold chisels from Amateur Work (Boston, 1904): octagonal tool steel or old files forged about 5 in. long, flat chisels 3/8 to 1 in. with a 60 degree edge, plus gouges, side, cape, diamond-point and round-nose chisels; only the last 1/8 in. of the edge hardened, tempered light purple for steel or dark purple for iron.
ระดับกลาง
Two or three days for the set

คำแนะนำ

1

His sizes

กำลังโหลดสมุด Jupyter…
2

Read Griswold

"When the tool is forged the edge only must be hardened for about 1/8 in., the metal above being left softer to withstand the shock."
3

Forge the blanks

From octagonal tool steel (or old files) forge each chisel about 5 in. (127 mm) from head to edge with a gradual taper to the edge, and forge the head down so it does not broom. Forging steps are ours: forge at a bright red only, as in his part I.

วัสดุสำหรับขั้นตอนนี้:

เหล็กเครื่องมือแปดเหลี่ยมเหล็กเครื่องมือแปดเหลี่ยม1 ชิ้น

เครื่องมือที่ต้องใช้:

เตาตีเหล็กของช่างตีเหล็กเตาตีเหล็กของช่างตีเหล็ก
ทั่งทั่ง
ค้อนค้อน
คีมช่างตีเหล็กคีมช่างตีเหล็ก
4

Shape the edges

Flat chisels 3/8, 1/2, 5/8 and 1 in. wide; gouges 1/4-5/8 in. with the bevel inside; side chisels 1/4, 3/8, 1/2 in. with the edge in one flat side; cape chisels 3/16 and 1/4 in. with the stock behind slightly thinner; a diamond point about 1/8 in. on the square (bent version for flat work); round-nose chisels, heavy and a long-tapered drawing chisel (his fig. 1).

เครื่องมือที่ต้องใช้:

เตาตีเหล็กของช่างตีเหล็กเตาตีเหล็กของช่างตีเหล็ก
ทั่งทั่ง
ค้อนค้อน
ตะไบ (ตะไบมือ)ตะไบ (ตะไบมือ)
5

Harden the edge only

Heat the edge and harden only about 1/8 in. (3 mm) of it in water, leaving the body softer: a chisel hard too far up cracks off on a line under a heavy blow.

วัสดุสำหรับขั้นตอนนี้:

น้ำน้ำ1 ชิ้น

เครื่องมือที่ต้องใช้:

เตาตีเหล็กของช่างตีเหล็กเตาตีเหล็กของช่างตีเหล็ก
คีมช่างตีเหล็กคีมช่างตีเหล็ก
ถังถัง
6

Temper purple

Brighten the edge with emery cloth and let the heat run the colour down: light purple (530 F) for chisels used on steel, dark purple (550 F) for cast and wrought iron; then cool.

วัสดุสำหรับขั้นตอนนี้:

ผ้าทรายอีเมอรีผ้าทรายอีเมอรี1 ชิ้น
น้ำน้ำ1 ชิ้น

เครื่องมือที่ต้องใช้:

ถังถัง
7

Grind

Grind the flat chisel edges to about 60 degrees (45-75: blunter for heavy work), keeping the edge from blueing.

เครื่องมือที่ต้องใช้:

เครื่องเจียรตั้งโต๊ะเครื่องเจียรตั้งโต๊ะ
8

Troubleshooting

Cold chisel troubleshooting.

Flow

Loading...
9

History and honest limits

From Robert Gibson Griswold, "Tool Making for Amateurs" II, **Amateur Work** (Boston), vol. III (1903-04), pp. 304-305 and fig. 1 (checked on the archive.org scan amateurwork03bostrich); temper temperatures from his part I table. Forging heats, metric figures and tools are ours.

วัสดุ

3

เครื่องมือที่จำเป็น

7

พิมพ์เขียวนี้สร้าง

บลูพริ้นท์ที่เกี่ยวข้อง

บลูพริ้นท์เหล่านี้แบ่งปันความรู้ — เทคนิค วัสดุ หรือหลักการ

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...