ศิลปะ
ความงามและสุขภาพ
งานฝีมือ
วัฒนธรรมและประวัติศาสตร์
ความบันเทิง
สิ่งแวดล้อม
อาหารและเครื่องดื่ม
วิศวกรรมย้อนรอย
วิทยาศาสตร์
กีฬา
เทคโนโลยี
อุปกรณ์สวมใส่
Hot-Water Cylinder Churn: Cream Is Crushed Between a Warm Turning Cylinder and an Adjustable Plate, Then Falls to a Dasher
Buttercup

สร้างโดย

Buttercup

11. พฤศจิกายน 2026IE
6
0
0
0
0

Hot-Water Cylinder Churn: Cream Is Crushed Between a Warm Turning Cylinder and an Adjustable Plate, Then Falls to a Dasher

Jason W. Hardie of New York received US 27,446, dated 13 March 1860, for a churn. Cream in a hopper is drawn between a turning cylinder filled with hot water and a plate set close against it, which crushes the butter globules and warms them only for that moment; it falls in a thin sheet into the churn body, losing the heat again, and a dasher driven by a band from the cylinder gathers the butter. The patent gives no sizes and no water temperature; every size here is ours.
ขั้นสูง
About 3 days, plus printing

คำแนะนำ

1

Warm for a moment only

กำลังโหลดสมุด Jupyter…
2

A turning cylinder churn, one month before

Ward churns inside his cylinder. Hardie works the cream on the outside of his, against a plate.
3

Read US 27,446

"It is desirable to have the butter globules warmed only at the moment they are acted on, and to heat the milk or cream as little, and as little time, as possible, to make good butter." ... "And the cream, after passing under the cylinder, falls in a thin sheet, or in small streams, or drops, through the air, into the churn body beneath, thereby again parting with much of the heat acquired from the cylinder."
4

Print the cog-wheel h

Spur gear, module 2.5, 60 teeth, 18 mm wide, with a hub 30 mm across; bored 16.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
ไฟล์แบบSTLCC0 - Free
5

Print the pinion i

Spur pinion, module 2.5, 16 teeth, 18 mm wide, with a hub 30 mm across; bored 16.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
ไฟล์แบบSTLCC0 - Free
6

Print the pulleys G and H

Pulley 100 mm across with a round groove for an 8 mm belt; bored 16.4 mm. Print two. PETG, 0.2 mm layers, 40 % infill, 4 walls.
ไฟล์แบบSTLCC0 - Free
7

Churn body C and frame I

From 20 mm hardwood board make the body 400 x 350 mm inside and 350 deep; glue and screw it and seal the inside joints with silicone sealant. Bore the two long walls 16.8 mm across, 120 mm above the floor and on the centre line, for the dasher's shaft p. For the frame I cut two cheeks 440 x 230 mm that stand on the body's long walls, joined by cleats so the frame lifts off. Bore both cheeks 16.8 mm for the cylinder's shaft l, 40 mm from the centre and 120 mm above the body's top edge, and 16.8 mm for the winch shaft g, 95 mm from l at 45 degrees up and outward. Screw a hardwood cross-piece f, 40 x 20 mm, between the cheeks under the plate's place, and fit a nut in it for the thumb-screw d.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง4 ชิ้น
กาวไม้กาวไม้1 ชิ้น
สกรูไม้สกรูไม้40 ชิ้น
ซิลิโคนยาแนวซิลิโคนยาแนว1 ชิ้น
น็อตหกเหลี่ยมน็อตหกเหลี่ยม1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยวงเดือนตั้งโต๊ะเลื่อยวงเดือนตั้งโต๊ะ
เลื่อยจิ๊กซอว์เลื่อยจิ๊กซอว์
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
แคลมป์แบบบาร์แคลมป์แบบบาร์
ชุดไขควงชุดไขควง
ตลับเมตรตลับเมตร
กระดาษทรายกระดาษทราย
8

Cylinder B, shaft l and stopper m

Cut 300 mm of stainless tube 160 mm across. Cut two end discs from 15 mm HDPE sheet to fit inside it; bore both 16 mm on the centre for a 16 mm stainless shaft, 500 mm long, and one 20 mm, 50 mm off centre, for a rubber stopper. Press the discs into the tube on the shaft, screw them through the tube with stainless screws, and seal the discs and the shaft's passage with silicone sealant so the cylinder holds water.

วัสดุสำหรับขั้นตอนนี้:

ท่อสเตนเลสท่อสเตนเลส1 ชิ้น
แผ่น HDPEแผ่น HDPE1 ชิ้น
แท่งสเตนเลสแท่งสเตนเลส1 ชิ้น
จุกยางจุกยาง1 ชิ้น
สกรูเกลียวมิลสกรูเกลียวมิล12 ชิ้น
ซิลิโคนยาแนวซิลิโคนยาแนว1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
เลื่อยจิ๊กซอว์เลื่อยจิ๊กซอว์
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
ตะไบ (ตะไบมือ)ตะไบ (ตะไบมือ)
ชุดไขควงชุดไขควง
9

Hopper A, plate a, packing strips b and thumb-screw d

Make a hardwood hopper 302 mm long inside, to take the cylinder: an outer wall, two end walls and a bottom sloping down to the cylinder, its inner edge cut to the cylinder's curve. Bend a strip of stainless sheet to the curve and screw it over that edge as the plate a. Screw HDPE strips on the end walls' inner faces as packing b, to run against the cylinder's ends. Hang the hopper's outer bottom corner on a 10 mm stainless pin c through the cheeks. Cut 60 mm of threaded rod with a wing nut locked on one end as the thumb-screw d; run it up through the cross-piece's nut to bear under the hopper, and turn it until the plate is about 1.5 mm from the cylinder.

วัสดุสำหรับขั้นตอนนี้:

แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง1 ชิ้น
แผ่นสเตนเลสแผ่นสเตนเลส1 ชิ้น
แผ่น HDPEแผ่น HDPE1 ชิ้น
แท่งสเตนเลสแท่งสเตนเลส1 ชิ้น
เพลาเกลียวเพลาเกลียว1 ชิ้น
น็อตปีกผีเสื้อน็อตปีกผีเสื้อ1 ชิ้น
น็อตหกเหลี่ยมน็อตหกเหลี่ยม1 ชิ้น
สกรูไม้สกรูไม้16 ชิ้น
กาวไม้กาวไม้1 ชิ้น

เครื่องมือที่ต้องใช้:

เลื่อยวงเดือนตั้งโต๊ะเลื่อยวงเดือนตั้งโต๊ะ
เลื่อยจิ๊กซอว์เลื่อยจิ๊กซอว์
กรรไกรตัดแผ่นโลหะกรรไกรตัดแผ่นโลหะ
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ประแจเลื่อนประแจเลื่อน
ชุดไขควงชุดไขควง
10

Dasher D, gears, winch E and band n

Pass a 16 mm stainless shaft p through the body's walls and fit the dasher on it: a hardwood hub with eight 12 mm dowel arms reaching 100 mm, in three sets along the shaft. Fit the cylinder's shaft in the cheeks with the pinion i on one end and the pulley G on the other, the cog-wheel h on the winch shaft g meshing the pinion, and a hardwood crank with a dowel handle on g as the winch E. Fit the pulley H on the dasher shaft's end, under G, and join them with a round belt. Hold every shaft with collars.

วัสดุสำหรับขั้นตอนนี้:

แท่งสเตนเลสแท่งสเตนเลส2 ชิ้น
แผ่นไม้เนื้อแข็งแผ่นไม้เนื้อแข็ง1 ชิ้น
เดือยไม้เนื้อแข็งเดือยไม้เนื้อแข็ง2 ชิ้น
กาวไม้กาวไม้1 ชิ้น
เส้นใย PETGเส้นใย PETG1 ชิ้น
สายพานขับสายพานขับ1 ชิ้น
Shaft CollarShaft Collar6 ชิ้น
สลักผ่าสลักผ่า2 ชิ้น

เครื่องมือที่ต้องใช้:

เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)เครื่องพิมพ์สามมิติแบบเส้นใย (FDM)
เลื่อยตัดเหล็กเลื่อยตัดเหล็ก
ตะไบ (ตะไบมือ)ตะไบ (ตะไบมือ)
สว่านไร้สายสว่านไร้สาย
ชุดดอกสว่านชุดดอกสว่าน
ปากกาจับชิ้นงานหน้าโต๊ะปากกาจับชิ้นงานหน้าโต๊ะ
ประแจเลื่อนประแจเลื่อน
11

The build in 3D

FreeCAD model of this build, partly cut away: the body C with the dasher D, the frame I, the cylinder B on its shaft with the pinion i and cog-wheel h on the winch shaft, the hopper A with its plate a against the cylinder, the pivot c and thumb-screw d, and the band n from pulley G to pulley H.
ไฟล์แบบBLENDCC0 - Free
12

Churn

Fill the cylinder with warm water from the kettle through the stopper's hole and close it; the patent gives no temperature, so check it with the thermometer and note it with the time the butter takes. Pour about 6 litres of heavy cream at about 15 °C into the hopper and turn the winch steadily, timing it; add cream to the hopper as it runs through. When the butter has gathered on the dasher, lift off the frame, take out the butter, tip the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

วัสดุสำหรับขั้นตอนนี้:

ครีมสดครีมสด6 l
น้ำน้ำ1 ชิ้น
เกลือทะเลเม็ดหยาบเกลือทะเลเม็ดหยาบ1 ชิ้น

เครื่องมือที่ต้องใช้:

กาต้มน้ำไฟฟ้ากาต้มน้ำไฟฟ้า
เทอร์มอมิเตอร์หัววัดแบบเสียบค้างเทอร์มอมิเตอร์หัววัดแบบเสียบค้าง
นาฬิกาจับเวลานาฬิกาจับเวลา
เครื่องชั่งดิจิทัลสำหรับครัวเครื่องชั่งดิจิทัลสำหรับครัว
ชามผสมสเตนเลสใบใหญ่ชามผสมสเตนเลสใบใหญ่
13

Troubleshooting

Hot-water cylinder churn troubleshooting.

Flow

Loading...
14

History and honest limits

**Jason W. Hardie** of New York, US 27,446, 13 March 1860 (signed 25 October 1859), "Churn". He disclaimed cylinders working against each other, plane rubbing surfaces, and hot water in the dasher or the main body of cream, and claimed the hollow revolving cylinder with hot water and an adjustable fixed surface against it. He gives no water temperature and no sizes; every size here is ours, our gears and pulleys are printed and sit on opposite ends of the cylinder, where his are on one end.

วัสดุ

21

เครื่องมือที่จำเป็น

19

ไฟล์ออกแบบ

4

CC0 สาธารณสมบัติ

พิมพ์เขียวนี้เผยแพร่ภายใต้ CC0 คุณสามารถคัดลอก แก้ไข แจกจ่าย และใช้งานผลงานนี้เพื่อวัตถุประสงค์ใดก็ได้ โดยไม่ต้องขออนุญาต

สนับสนุนเมกเกอร์โดยซื้อสินค้าผ่านพิมพ์เขียวของพวกเขา ซึ่งพวกเขาจะได้รับ ค่าคอมมิชชันเมกเกอร์ ที่ผู้ขายกำหนด หรือสร้างเวอร์ชันใหม่ของพิมพ์เขียวนี้และรวมเป็นการเชื่อมต่อในพิมพ์เขียวของคุณเพื่อแบ่งรายได้

การสนทนา

(0)

เข้าสู่ระบบ เพื่อร่วมการสนทนา

กำลังโหลดความคิดเห็น...